Nov . 16, 2026 00:33 Back to list

Deep well submersible pump price: match 200QJR to your well

Summary

Deep well submersible pump price is easier to judge after the well, water, power, flow, and installation conditions are matched. The 200QJR uses three-phase AC 380V power, works with 50Hz supply, and supports vertical installation with immersion up to 70m. This guide explains where the 200QJR fits, which operating limits matter, and what to prepare before requesting a quotation.

Deep well submersible pump price: match 200QJR to your well
Illustration for reference; see the product page for actual photos and specifications.

A useful deep well submersible pump price decision starts with operating fit. The 200QJR is intended for vertical well installation and three-phase AC 380V, 50Hz power. Its selection depends on water chemistry, well geometry, required flow and head, immersion depth, and the protection equipment around the motor.

What determines the quotation

The 200QJR configuration is the first price factor to settle. Flow and head identify the suitable model within the series. The range includes lower-head and higher-head options in the 20m3/h group, as well as options in the 25m3/h group. Rated power changes between configurations, so we need the required flow and head before identifying the pump for your system.

The electrical arrangement, frequency-converter integration, cable, and external overload protection also affect the requested package. We undertake OEM processing for special non-standard submersible motor and pump requirements based on user needs. Well diameter, immersion depth, water condition, and installation method then determine whether the selected configuration fits the site.

Our advice

Choose the 200QJR for a vertical well with 200mm and above diameter, at least 3m bottom clearance, complete immersion, and immersion depth not exceeding 70m. Match flow and head to a series configuration. It suits three-phase AC 380V, 50HZ systems and can work with a frequency converter. Water limits are temperature not above 20 °C, pH between 6.5-8.5, solid impurities no greater than 0.01%, hydrogen sulfide no more than 1.5mg/L, and chloride ions no more than 400mg/L.

Confirm the well and water conditions

The 200QJR suits a vertical well where the pump can remain completely immersed. The immersion depth must not exceed 70m, and the distance from the bottom of the well must be at least 3m. The pump is for vertical use and cannot be installed horizontally or at an angle.

The well diameter must be 200mm and above. Check the bore before comparing configurations, because the hydraulic selection is useful only when the pump can be positioned correctly and kept clear of the bottom.

Water quality sets another boundary. The water temperature must not exceed 20 °C. Solid impurities must be no greater than 0.01%, the pH value must be between 6.5-8.5, hydrogen sulfide must be no more than 1.5mg/L, and chloride ions must be no more than 400mg/L.

What to weigh

Well fit · vertical installation, 200mm and above, with at least 3m bottom clearance
Water fit · temperature, pH, solids, hydrogen sulfide, and chloride limits
Hydraulic fit · required flow and head matched to a 200QJR configuration
Electrical fit · three-phase AC 380V, 50HZ supply and protection equipment
Integration fit · immersion up to 70m, water filling, cable, and overload protection

Match flow and head to the application

Choose the model from the flow and head the delivery system requires. For example, the 20m3/h group includes 200QJ20-40 with 40m head and 200QJ20-108 with 108m head. The 25m3/h group includes 200QJ25-28 with 28m head and 200QJ25-112 with 112m head. These examples show why the model number alone is not enough for a quotation.

Selection point200QJR requirementBuyer check
Power supplyThree-phase AC 380V, tolerance ± 5%Confirm the available three-phase supply
Frequency50HZ, tolerance ± 1%Match the site frequency
Immersion depthNot more than 70mMeasure the planned pump position
Bottom clearanceAt least 3mKeep the pump clear of the well bottom
Water temperatureNot higher than 20 °CCheck the water temperature
Flow control0.7-1.2 times rated flowKeep operation within the rated range
Applicable well diameter200mm and aboveCompare the bore with the pump size

The pump output must remain at 0.7-1.2 times the rated flow, and the water flow in the well must support the pump output and continuous operation. Send the required flow, head, and well diameter so we can identify the suitable configuration.

Review the electrical and motor arrangement

The pump uses three-phase AC 380V power at 50HZ. The supply tolerances are ± 5% for voltage and ± 1% for frequency, so the available power should be checked before the pump is integrated into an existing control panel.

The water-filled motor uses 50W400 high-grade cold rolled silicon steel. Its stator is stamped by a high-speed punch, and the winding uses a high-temperature, anti-aging design. The impeller shaft uses 3CR13 stainless steel with a high-temperature sleeve and other accessories. The water-filled structure provides cooling and lubrication during operation.

A frequency converter can adjust output according to water consumption. This suits systems where demand changes during the day. Include the control method and expected operating pattern with the hydraulic requirements so we can review the pump and control arrangement together.

Prepare the installation and protection package

Fill the pump with water before use and tighten the water and air exhaust bolts. The pump must be completely immersed, and it must not be tested without water or under no-load conditions.

The cable and external overload protection device must be selected according to the pump requirements. Installation planning should also account for vertical placement, immersion depth, bottom clearance, and water flow in the well. These conditions determine whether the pump can operate within its required output range.

The 200QJR is used for water extraction in agricultural irrigation, high-rise water supply, mountain water supply, river water intake, domestic water systems, and community water towers. Choose it when the well, water, electrical supply, flow, and head all match the series requirements.

Your shortlist

200QJR deep well submersible pump · suits vertical wells with 200mm and above diameter, immersion up to 70m, water within the stated limits, and matching flow and head

Details to settle before ordering

Which rating applies to 200QJ20-40?

The 200QJ20-40 configuration is rated at 20m3/h flow, 40m head, and 4KW rated power. It uses 380V rated voltage and has 10.1A rated current. Its listed motor efficiency is 76.0%, power factor is 0.79, outlet diameter is 50mm, and unit radial maximum size is 184mm. Use these values when checking the selected configuration against your electrical and pipe arrangement.

Which rating applies to 200QJ25-112?

The 200QJ25-112 configuration is rated at 25m3/h flow, 112m head, and 13KW rated power. Its rated voltage is 380V and rated current is 29.8A. The listed motor efficiency is 80.0%, power factor is 0.83, outlet diameter is 65mm, and unit radial maximum size is 184mm. These figures help you review the higher-head option before requesting a quotation.

What should be checked when comparing the two flow groups?

The 20m3/h and 25m3/h groups use different hydraulic requirements and include different head options. The 20m3/h examples range from 40m to 108m head, while the 25m3/h examples include 28m and 112m head. Compare the required flow first, then check head, rated power, current, and outlet diameter for the chosen configuration.

Select from the site conditions

The 200QJR deep well submersible pump suits a vertical well with 200mm and above diameter, three-phase AC 380V power, water within the stated limits, and a flow and head requirement covered by the series. We can review special non-standard requirements through OEM processing. Send the well dimensions, water test results, hydraulic duty, and electrical arrangement for a quotation.

The company

Hebei Aochite Water Supply and Drainage Equipment Technology Co., Ltd.

The company was established in 2000, after 20 years of development, the existing plant area of 67 acres, modern workshop 16,000 square meters.The company has gathered a large number of high-quality scientific research management and production personnel.Built the most advanced PMSCAT pump automatic test system designed by Beijing Academy of Agricultural Sciences, China, test power 400KW laboratory.For the company's pump stator, core and other accessories test to provide reliable detection data, so that the…

About Us ↗Visit company website ↗


Share

Next:

This is the last article

  • Deep well submersible pump price: match 200QJR to your well
    Deep well submersible pump price: match 200QJR to your well
    Compare deep well submersible pump price by matching 200QJR flow, head, well diameter, water limits, power supply, and installation conditions.
    Detail
  • What Is the Best Submersible Well Pump for a 135QJP Installation?
    What Is the Best Submersible Well Pump for a 135QJP Installation?
    Find out what is the best submersible well pump for a 135QJP installation by checking power, water quality, immersion depth, vertical positioning, cable selection, and startup requirements.
    Detail
  • What Is the Best Deep Well Submersible Pump? Integration, Spare Parts & Maintenance FAQ
    What Is the Best Deep Well Submersible Pump? Integration, Spare Parts & Maintenance FAQ
    Not sure what is the best deep well submersible pump for your project? This FAQ covers integration requirements, water-quality limits, wearing parts and maintenance schedules for the QJB and 200QJ series from Hebei Aochite Water Supply and Drainage Equipment Technology Co., Ltd.
    Detail

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.