150QJ duboko uronjena pumpa

QJ series submersible electric pump is a kind of lifting machine directly connected to the submersible motor and pump to work in the water. This series of pumps are vertical, with small footprint, compact structure, simple installation, easy maintenance and repair. It is widely used in agricultural irrigation, municipal engineering, water conservancy, urban water supply and drainage, as well as industrial and mining enterprises, disaster relief drainage and other fields. The flow range is 5-500m3/h, the head is 4-800m, and the power is 3-315KW. This submersible electric pump can efficiently lift and transport water, providing reliable water supply protection for various fields. Its stable performance and solid structure make it an indispensable machine in various water conservancy projects.

This product is a three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%) power supply pump, is designed for water requirements of strict occasions. The product is suitable for water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L water quality environment. The pump adopts closed or water-filled wet structure motor, the inner cavity must be filled with clean water before use to prevent virtual filling, and then tighten the water injection and pressure relief bolts. The product shall be completely immersed in water, the penetration depth shall not exceed 70m, and the distance from the bottom of the well shall not be less than 3m. The water source required by the pump shall be able to meet its output demand and continuous operation, and the output of the pump shall be controlled at 0.7-1.2 times of the rated flow. The well shall be vertical, and the horizontal or inclined use shall be prohibited, and the cable shall be matched according to the requirements and equipped with external overload protection device. It is strictly prohibited to conduct no water test on the electric pump.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade 380/50HZ, the use of other voltage grades of submersible motors need to be customized.The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious sign:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering and steering instructions are the same.When the pump is upright, pay attention to safety, prevent overturning injury.

5, this pump has won wide acclaim for its efficiency and reliability. It is used in strict accordance with the applicable lift and flow range stipulated by the electric pump to avoid excessive wear of thrust bearings and other parts caused by large flow at low lift or excessive pumping force at high lift, resulting in motor overload and burnout. After being put into the well, the insulation resistance to the ground of the electric pump shall be measured and shall not be less than 100MΩ. After starting, the voltage and current shall be observed regularly, and the insulation of the motor winding shall be checked to meet the specified requirements. If the storage temperature is below freezing, the water in the pump shall be dried to avoid damage to the motor due to low temperature freezing in the motor cavity. This electric pump is your reliable choice, which can provide stable and reliable power support for your work.

Structure brief: pump part is mainly composed of pump shaft, impeller, diversion shell, rubber bearing, check valve body (optional parts) and other components.The motor part is mainly composed of base, pressure regulating film, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet joint, lead cable and other components.

Glavne karakteristike proizvoda uključuju:

1. 1.The motor is a water-sealed wet submersible three-phase asynchronous motor.The motor cavity is filled with clean water for cooling the motor and lubricating the bearing.The voltage regulating film at the bottom of the motor is used to regulate the temperature rise caused by the motor.The expansion and contraction pressure difference of the body water caused by the change.
2. 2. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand ring is installed to form a sand prevention structure.
3. 3. In order to prevent the pump shaft from jumping at startup, the pump shaft is connected with the motor shaft through a coupling, and a thrust bearing is installed at the lower part of the motor.
4. 4. The lubrication of the motor and pump bearing is water lubrication.
5. 5. The motor stator winding is made of high-quality submersible motor winding wire, with excellent insulation performance.
6. 6. The pump is designed by computer CAD, with simple structure and excellent technical performance.

(1)Priprema prije instalacije:
1. Provjerite da li potopljena pumpa ispunjava uslove upotrebe i opseg koji je naveden u priručniku.
2. Koristeći teški predmet sa prečnikom jednakim maksimalnom spoljašnjem prečniku potopljene pumpe, izmerite da li unutrašnji prečnik bušotine može da stane na potapajuću pumpu i izmerite da li dubina bunara ispunjava zahteve za instalaciju.
3. Provjerite da li je bušotina čista i da li je voda zamućena. Nikada nemojte koristiti potapajuću električnu pumpu za pranje blata i pijeska vode iz welor pumpe kako biste izbjegli prijevremeno oštećenje potopljene električne pumpe.
4. Provjerite da li je položaj stezaljke za ugradnju uglavka prikladan i da li može izdržati kvalitet cijele jedinice
5. Provjerite jesu li komponente potopljene pumpe kompletne i pravilno instalirane prema dijagramu montaže u priručniku. Uklonite filterski zaslon i okrenite spojnicu da vidite da li se fleksibilno okreće
6. Odvrnite zavrtanj za vodu i napunite šupljinu motora čistom, nekorozivnom vodom (napomena. obavezno je napunite), a zatim zategnite vodeni vijak. Nakon 12 sati ubrizgavanja vode, otpor izolacije motora ne smije biti manji od 150M Q kada se mjeri pomoću stola za tresenje od 500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Priloženi dijagram procesa ožičenja kablova je sljedeći:

8. Pomoću multimetra provjerite da li su trofazne žice povezane i da li je DC otpor približno izbalansiran.
9. Provjerite da li su strujni krug i kapacitet transformatora preopterećeni, a zatim priključite prekidač za zaštitu od preopterećenja ili opremu za pokretanje. Pogledajte tabelu 2 za određene modele, a zatim ulijte kantu vode u pumpu za vodu iz izlaza pumpe za vodu da podmažite gumene ležajeve u pumpi, a zatim postavite potopljenu električnu pumpu uspravno i mirno. Pokrenite (ne više od jedne sekunde) i provjerite da li je smjer upravljanja u skladu sa znakom za upravljanje. Ako ne, zamijenite bilo koja dva konektora trofaznog kabla. Zatim instalirajte filter i pripremite se za spuštanje u bunar. Ako se koristi u posebnim prilikama (kao što su rovovi, jarci, rijeke, bare, bare, itd.), električna pumpa mora biti pouzdano uzemljena.

(2) Oprema i alati za instalaciju:
1. Jedan par lanaca za podizanje za više od dvije tone.
2. Stativ sa vertikalnom visinom ne manjom od četiri metra.
3. Dva viseća užad (žičana užad) koja mogu podnijeti težinu veću od jedne tone (mogu podnijeti težinu kompletne pumpe za vodu).
4. Ugradite dva para stezaljki (udlage).
5. Ključevi, čekići, odvijači, električni alati i instrumenti, itd.

(3) Instalacija električne pumpe:
1. Instalacioni dijagram potopljene električne pumpe prikazan je na slici 2. Specifične instalacijske dimenzije prikazane su u tabeli 3 "Lista instalacionih dimenzija potopljene električne pumpe".

2. Potopne električne pumpe sa naponom manjim od 30 metara mogu se dizati direktno u bunar pomoću crijeva i žičanih užadi ili drugih užadi od konoplje koja mogu podnijeti punu težinu cijele mašine, vodovodnih cijevi i vode u cijevima.

3. Pumpe sa naponom većim od 30 metara koriste čelične cijevi, a redoslijed ugradnje je sljedeći:
①Upotrijebite stezaljku da pričvrstite gornji kraj dijela pumpe za vodu (motor i pumpa za vodu su u ovom trenutku spojeni), podignite ga visećim lancem i polako ga vežite za bunar dok ne postavite stezaljku na vrh bunara i uklonite viseći lanac.
② Upotrijebite još jedan par stezaljki da stegnete cijev, podignite je lancem za vješanje 15 cm dalje od prirubnice i polako spustite. Između prirubnice cijevi i prirubnice pumpe Postavite gumenu podlogu na mjesto i zategnite cijev i pumpu ravnomjerno vijcima, maticama i opružnim podloškama.
③ Lagano podignite potapajuću pumpu, uklonite stezaljku na gornjem kraju pumpe za vodu, zavežite kabel čvrsto za cijev za vodu plastičnom trakom i polako je zavežite dok se stezaljka ne postavi na vrh bunara.
④Upotrijebite istu metodu za vezivanje svih vodovodnih cijevi u bunar.
⑤Nakon što je izlazni kabel spojen na kontrolnu sklopku, spaja se na trofazno napajanje.

(4) Stvari na koje treba obratiti pažnju prilikom instalacije:
1. Ako se tokom procesa pumpanja pronađe pojava zaglavljivanja, okrenite ili povucite cijev za vodu da biste savladali tačku zaglavljivanja. Ako razne mjere i dalje ne daju rezultate, molimo vas da nemojte silom pritiskati pumpu kako biste izbjegli oštećenje potapajuće električne pumpe i bunara.
2. Tokom ugradnje, gumeni jastučić treba postaviti na prirubnicu svake cijevi i ravnomjerno zategnuti.
3. Kada se pumpa za vodu spusti u bunar, treba je postaviti na sredinu cijevi bunara kako bi se spriječilo da pumpa dugo radi o zid bunara, uzrokujući vibriranje pumpe, a motor da briše i gori .
4. Odredite dubinu pumpe za vodu do dna bunara u skladu sa uslovima protoka peska i mulja u bunaru. Nemojte zakopavati pumpu u blato. Udaljenost od pumpe za vodu do dna bunara općenito nije manja od 3 metra (vidi sliku 2).
5. Dubina ulaza vode u pumpu za vodu ne bi trebala biti manja od 1-1,5 metara od dinamičkog nivoa vode do ulaznog čvora vode (vidi sliku 2). U suprotnom, ležajevi pumpe za vodu mogu se lako oštetiti.
6. Podizanje vodene pumpe ne smije biti prenisko. U suprotnom, na cevovodu za vodu na ušću bunara potrebno je instalirati zasun za kontrolu protoka pumpe na nazivnoj tački protoka kako bi se sprečilo preopterećenje i izgorevanje motora usled velikih brzina protoka.
7. Kada pumpa za vodu radi, izlaz vode treba da bude kontinuiran i ravnomeran, struja treba da bude stabilna (pod nominalnim radnim uslovima, generalno ne više od 10% nazivne struje), i ne bi trebalo da bude vibracija ili buke. Ako postoji bilo kakva abnormalnost, mašinu treba zaustaviti kako bi se otkrio uzrok i otklonio ga.
8. Prilikom ugradnje obratite pažnju na podešavanje žice za uzemljenje motora (pogledajte sliku 2). Kada je cijev za vodu čelična cijev, vodite je od stezaljke na glavi bunara; kada je cijev za vodu plastična cijev, vodite je od oznake uzemljenja električne pumpe.

1. (1)After the submersible pump is installed, check the insulation resistance and three-phase conduction from the switch again, check whether the instrument and the connection of the start equipment are wrong, if there is no problem, the trial machine can be started, and observe whether the indicator readings of the instrument exceed the rated voltage and current specified on the nameplate after the start, and observe whether the pump has noise and vibration phenomenon, and put into operation if everything is normal.
2. (2)After the first operation of the pump for four hours, the motor should be shut down to test the thermal insulation resistance quickly, and its value should not be less than 0.5 megaohm.
3. (3)After the pump is shut down, it should be started after five minutes to prevent the water column in the pipe from being completely reflowed and causing excessive motor current and burnout.
4. (4)After the pump is put into normal operation, in order to prolong its service life, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. If the following conditions are found, the pump should be shut down immediately to troubleshoot.

1 In the rated condition, the current exceeds 20%.

 2 Dinamički nivo vode pada na ulazni dio vode, uzrokujući isprekidanu vodu.

 3 Potopljena pumpa ima jake vibracije ili buku.

 4 Napon napajanja je manji od 340 volti.

 5 Osigurač je pregorio.

 6 Cijev za dovod vode je oštećena.

 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.

5.  
6. (5)Unit disassembly:

 1 Untie the cable tie, remove the pipeline part, and remove the wire plate.

 2 zavrnite vijak za vodu, stavite vodu u komoru motora.

 3 uklonite filter, otpustite fiksirani vijak na spojnici da biste učvrstili osovinu motora.

 4 zavrnite vijak koji povezuje ulazni dio vode sa motorom i odvojite pumpu od motora (obratite pažnju na jastuk jedinice prilikom odvajanja, kako biste spriječili savijanje osovine pumpe)

 5 redoslijed rastavljanja pumpe je: (vidi sliku 1) ulazni dio vode, impeler, odvodna školjka, impeler...... tijelo nepovratnog ventila, kada skidate impeler, koristite posebne alate da olabavite konusnu čauru fiksnog prvo radno kolo i izbjegavajte savijanje i nagnječenje osovine pumpe u procesu demontaže.

 6 proces rastavljanja motora je: (vidi sliku 1) stavite motor na platformu i uklonite matice, bazu, maticu za zaključavanje glave vratila, potisnu ploču, ključ, donje sjedište ležaja vodilice i vijak s dvostrukom glavom sa dna motor zauzvrat, a zatim izvadite rotor (pazite da ne oštetite paket žica) i na kraju uklonite spojni dio i gornje sjedište ležaja vodilice.

 7 montaža jedinice: prije montaže, rđu i prljavštinu dijelova treba očistiti, a spojnu površinu i pričvrsne elemente premazati brtvilom, a zatim ih sastaviti suprotnim redoslijedom od rastavljanja (osovina motora se pomiče gore-dolje nakon montaže oko jedan milimetar), nakon montaže, spojnica treba biti fleksibilna, a zatim mašina za ispitivanje filterskog sita. Potopljene pumpe se iz bunara izvode radi demontaže i održavanja u skladu sa članom 5. nakon godinu dana rada, odnosno manje od godinu dana rada ali dve godine ronjenja, a istrošeni delovi se zamenjuju.

In order to ensure long-term use of your submersible pump, we strongly recommend that you drain the water in all motor cavities especially in winter to prevent the motor from freezing; at the same time, roll up the cable and tie it well. Store the equipment in a room without corrosive substances and gases, with the temperature below 40 °C. In addition, if you do not use the submersible pump for a long time, be sure to pay attention to rust prevention measures. These simple steps will help you maintain the performance of the equipment and extend its service life.

01 Duboki zahvat vode iz bunara

02 Visoko vodosnabdijevanje

03 planinski vodovod 

04 toranj voda

05 Poljoprivredno navodnjavanje

06 navodnjavanje vrta

07 vodozahvat rijeke

08 kućna voda