200QJR Bamka Hoosta Hoose

Hot water motor using 50W400 high grade cold rolled silicon steel, stamping by high speed punch, make its stator iron loss is low, less heating advantages, the motor winding using high temperature, anti-aging hot water motor special winding water line, using 3CR13 stainless steel impeller shaft, high temperature sleeve and other high quality accessories, so that it can run at high temperature for a long time, and can be used with a frequency converter, so that it can automatically adjust according to the size of the water consumption.

This product is a three-phase AC 380V power supply (tolerance ± 5%), 50HZ frequency (tolerance ± 1%) pump, suitable for pumping water temperature not higher than 20 °C water. Specific requirements include: solid impurities content is not greater than 0.01%; PH value between 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The pump adopts closed or water sealed structure, before use must be filled with water, tighten the water and air exhaust bolts, otherwise not to use. The pump must be completely immersed in water, immersion depth shall not exceed 70m, and the distance from the bottom of the well shall not be less than 3m. The water flow in the well shall meet the requirements of the pump output and continuous operation, the pump output shall be controlled at 0.7-1.2 times the rated flow. The well shall be vertical, the pump can not be used horizontally or tilted, only vertical use. The pump must be equipped with cables and external overload protection device according to the requirements. It is strictly prohibited to test the pump without water and no load.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, si adag sida ku xusan qodobbada wiishka bamka, kala duwanaanshaha socodka isticmaalka, si looga hortago socodka hooseeya ama xoogga sare ee wiishka, xajinta iyo qaybaha kale ee xirashada, culeyska matoorka ayaa gubtay

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Hordhac kooban oo qaab dhismeed ah: qaybta bamka waxay inta badan ka kooban tahay shafka bamka, impeller, qolof leexinta, caag-jiidka, jeegaga jidhka (qaybaha ikhtiyaariga ah) iyo qaybo kale. Qaybta matoorka waxay inta badan ka kooban tahay saldhigga, filimka xakameynaya cadaadiska, riixitaanka, saxanka riixida, kursiga hagaha hoose, stator, rotor, kursiga hagaha sare, giraanta ciidda, qaybta gelinta biyaha, fiilada iyo qaybaha kale.

Tilmaamaha ugu muhiimsan ee alaabta waxaa ka mid ah:

 1, Matoorku waa matoor saddex-waji ah oo aan caadi ahayn oo qoyan oo qoyan, godka matoorka waxaa ka buuxa biyo nadiif ah, oo loo isticmaalo in lagu qaboojiyo matoorka oo lagu subiyo xajinta, filimka xakamaynta cadaadiska ee hoose ee matoorka ayaa loo isticmaalaa in lagu hagaajiyo. kala duwanaanshaha cadaadiska balaadhinta iyo foosha ee biyaha gudaha jidhka oo ay sababtay isbeddelka heerkulka sare u kaca ee matoorka.

 2, Si aan ciidda ceelka biyaha ku jirta uga dhicin matoorka, qaybta sare ee shafka matoorka waxaa lagu rakibay laba shaabad oo saliid ah, waxaana lagu rakibay giraan ciid si loo sameeyo qaab-dhismeed ka hortagga ciidda.

 3, Si looga hortago in bamka bamka uu kor u kaco marka la bilaabayo, bamka bamka iyo matoorka ayaa ku xiran isku-xirnaanta, waxaana lagu dhejiyaa tuubada sare ee qaybta hoose ee matoorka.

 4, Saliidda matoorka iyo bamka xajinta waa saliidda biyaha.

 5, Dabaylaha stator motor ka samaysan yahay silig motor submersible tayo sare leh, oo leh waxqabadka dahaarka sare.

 6, Bamka waxaa loogu talagalay kombuyuutar CAD, oo leh qaab-dhismeed fudud iyo waxqabad farsamo oo wanaagsan.

(1) Diyaarinta ka hor inta aan la rakibin:
1. Hubi in bamka hoos mara uu buuxiyo shuruudaha isticmaalka iyo baaxadda lagu sheegay buug-gacmeedka.
2. Adigoo isticmaalaya dhexroor culus oo leh dhexroor la mid ah dhexroorka dibadda ee ugu sarreeya ee bamka hoos mara, cabbir haddii dhexroorka ceelka ceelka uu ku habboon yahay bamka hoos mara, cabbirna haddii qoto-dheeraanta ceelku buuxinayo shuruudaha rakibidda.
3. Hubi in ceelka ceelku uu nadiif yahay iyo in biyuhu ceelku yihiin kuwo gurracan. Weligaa ha isticmaalin bam koronto oo hoos iman kara si aad u dhaqdo bamka weriyaha dhoobada iyo biyaha ciidda si aad uga fogaato dhaawac degdeg ah oo soo gaadha bamka korontadu hoos u dhigto.
4. Hubi in booska xajinaha welhead ku habboon yahay iyo haddii ay u adkeysan karto tayada unugga oo dhan
5. Hubi in qaybaha matoorka hoos u dhigi karaan ay dhammaystiran yihiin oo si sax ah loo rakibay si waafaqsan jaantuska kulanka ee buug-gacmeedka, ka saar shaashadda oo beddel isku-xidhka si aad u aragto inay si dabacsan u wareegayso.
6. Ka fur furka biyaha oo ka buuxi godka matoorka biyo nadiif ah oo aan daxalaysan (xusuusnow in aad buuxiso), ka bacdina adkee xadhigga biyaha. Ka dib 12 saacadood oo duritaanka biyaha ah, caabbinta dahaarka ee matoorku waa in aanu ka yarayn 150M Q marka lagu cabbiro miis gariir 500V ah.
7. Isku-xidhka fiilada, ka jar caag 120mm ah oo ka mid ah daraf ka mid ah fiilada baxaysa iyo fiilada ku habboon ee leh mindi koronto-yaqaanka ka dibna ku rogrogmadaa dhererka saddexda fiilooyinka xudunta ah ee qaab go'an, ka saar xudunta 20mm naxaas ah, xoqin oksaydhka lakabka dibadda ee fiilada naxaasta leh mindi ama maro ciid, oo geli labada silig ee isku xidhan ee ku dhammaanaya palirs. Ka dib markaad lakabka si adag ugu xidho silig naxaas ah, si fiican oo adag u iibi, iyo ciid kasta. oogada dushiisa. Dabadeed, saddexda qaybood ee kala-goysyada, isticmaal cajaladda daboolka polyvester-ka si aad ugu duubto qaab nus ah oo isku xiran oo ah saddex berkedood. Ku duub labada daraf ee lakabka wax lagu duubo si adag adigoo isticmaalaya dunta nyion, ka dibna isticmaal qaab nus ah oo la tumay si aad ugu duubto cajaladda saddex lakab. Ku duub daboolka dibadda cajaladda daboolka cadaadiska sare ee saddex lakab. Ugu dambeyntii, isku laab saddexda xargo oo si isdaba joog ah ugu duub shan lakab oo leh cajalad cadaadis sare leh. Lakab kasta waa in si adag loo xidhaa, kala-goysyada is-dhexyaaca waa inay ahaadaan kuwo adag oo fim ah si ay uga hortagaan in biyuhu soo galaan oo waxyeello u geystaan ​​dahaarka. , kaas oo aan ka yarayn 100M Ω

Jaantuska habka fiilooyinka fiilooyinka ee ku lifaaqan waa sida soo socota:

8. Isticmaal multimeter-ka si aad u hubiso in xadhkaha saddexda weji ay isku xidhan yihiin iyo in iska caabbinta DC-ku ay qiyaas ahaan dheelli tiran yihiin.
9. Hubi in awoodda wareegga iyo beddelka ay si xad dhaaf ah u raran yihiin, ka dibna ku xidh furaha ilaalinta culayska ama qalabka bilowga. Ka eeg Shaxda 2 noocyo gaar ah, ka dibna ku shub baaldi biyo ah bamka biyaha ee ka soo baxa bamka biyaha si aad u saliidayn xadhkaha caagga ah ee bamka, ka dibna bamka korontadu hoos u dhigto dhig mid toosan oo joogto ah. Bilow (wax aan ka badnayn hal ilbiriqsi) oo hubi in jihada isteerinka ay waafaqsan tahay calaamadda isteerinka. Haddaysan ahayn, ku beddel laba xidhiidhiye oo ka mid ah fiilada saddexda weji leh. Kaddib rakib shaandhada una diyaari inaad ceelka dhaadhacdo. Haddii loo isticmaalo waqtiyo gaar ah (sida godadka, godadka, webiyada, balliyada, balliyada, iwm.), bamka korontadu waa in si la isku halleyn karo loo dejiyo.

(2) Qalabka iyo qalabka lagu rakibo:
1. Hal ka mid ah silsiladaha wax-qaadista ee ka badan laba tan.
2. Sadex geesood ah oo leh joog toosan oo aan ka yarayn afar mitir.
3. Laba xadhig oo ka laadlaad ah oo qaadi kara miisaan ka badan hal tan (waxay qaadi karaan culayska bambooyin biyo ah oo dhammaystiran).
4. Ku rakib laba-labo oo xajin ah (kabyo).
5. Biraha, dubbaha, kaashawiito, qalabka korontada iyo qalabka, iwm.

(3) Ku rakibida bamka korontada
1. Jaantuska rakibaadda ee bamka korontada hoostiisa ayaa lagu muujiyay Jaantuska 2. Cabbirrada rakibidda gaarka ah ayaa lagu muujiyay shaxda 3 "Liiska Cabbirrada Rakibaadda ee Bamka Korontada ee Submersible".

2. Bambooyin koronto oo hoos yimaada oo madax ka yar 30 mitir ayaa si toos ah loogu shubi karaa ceelka iyadoo la isticmaalayo tubooyinka iyo xargaha ama xargaha kale ee hemp kuwaas oo qaadi kara miisaanka buuxa ee dhammaan mishiinka, tuubooyinka biyaha, iyo biyaha tuubooyinka.

3. Bambooyin leh madax ka badan 30 mitir ayaa isticmaala tubooyinka birta, nidaamka rakibiddana waa sida soo socota.
①Isticmaal xajin si aad ugu xidho cidhifka sare ee qaybta matoorka biyaha (matoorka iyo bamka biyaha ayaa ku xidhan wakhtigan), ku qaad silsilad ka laadlaadsan, oo si tartiib ah ugu xidh ceelka ilaa aad xajinayso madaxa ceelka oo ka saar silsilad laadlaadsan.
② Isticmaal labo xajin oo kale si aad tuubada ugu xajiso, ku qaad silsilad laadlaad ah oo 15 cm ka fog garabka, oo si tartiib ah hoos ugu dhig. Inta u dhaxaysa flange tuubada iyo bamka bamka, dhig suufka caagga ah meesha oo adkee tuubada oo si siman ugu bamgareyso boolal, lawska iyo weelasha guga.
③ Xoogaa kor u qaad bamka hoos mara, ka saar xajinta cidhifka sare ee bamka biyaha, si adag ugu xidh fiilada tuubada biyaha cajalad balaastik ah, oo si tartiib ah hoos ugu xidh ilaa xajinta la dhigo madaxa ceelka.
④ Isticmaal isku qaab si aad ugu xidhid dhammaan tuubooyinka biyaha ceelka.
⑤Kadib markii fiilada macdanta "lead-out" lagu xiro furaha kantaroolka, waxay ku xiran tahay sahayda korontada ee saddexda weji.

(4) Waxyaabaha la xuso marka la rakibayo:
1. Haddi dhacdo isku buuqid ah la helo inta lagu jiro habka bamgareynta, leexi ama jiid tuubada biyaha si aad uga gudubto meesha saxmada leh. Haddii tillaabooyin kala duwani aanay weli shaqayn, fadlan ha ku qasbin bamka si aad uga fogaato burbur ku yimaadda bamka korontada ee hoos u dhigi kara iyo ceelka.
2. Inta lagu jiro rakibidda, suufka caagga ah waa in lagu dhejiyaa gees ka gees kasta oo tuubo ah oo la adkeeyo si siman.
3. Marka bamka biyaha lagu shubo ceelka waa in la dhex dhigaa dhuunta ceelka badhtankeeda si aanay bamku ugu socon darbiga ceelka muddo dheer, taasina ay keento in bamku gariiro oo matoorku xaaqo oo gubato. .
4. Go'aami qoto dheeraanta bamka biyaha ilaa gunta ceelka iyadoo loo eegayo ciidda qulqulaya iyo xaaladaha ciidda ee ceelka. Ha ku aasin bamka dhoobada. Masaafada u jirta bamka biyaha ilaa gunta ceelka guud ahaan waa mid aan ka yarayn 3 mitir (eeg sawirka 2).
5. Moolka gelitaanka biyaha ee bamka biyuhu waa in aanu ka yarayn 1-1.5 mitir heerka biyaha firfircoon ilaa marinka biyaha gelitaanka (eeg sawirka 2). Haddii kale, xadhkaha matoorka biyaha ayaa si fudud u dhaawacmi kara.
6. Wiishka bamka biyuhu ma noqon karo mid aad u hooseeya. Haddii kale, waxaa loo baahan yahay in lagu rakibo tuubada biyaha ee albaabka ceelka si loo xakameeyo socodka bamka ee barta socodka lagu qiimeeyay si looga hortago in matoorku uu si xad dhaaf ah u raro oo uu u gubto heerka socodka badan ee socodka awgeed.
7. Marka bamka biyuhu socdo, wax-soo-saarka biyuhu waa inuu ahaado mid joogto ah oo xitaa, hadda waa inuu ahaado mid deggan (marka la qiimeeyo xaaladaha shaqada, guud ahaan wax aan ka badnayn 10% ee hadda la qiimeeyay), waana inaysan jirin gariir ama buuq. Haddii ay jiraan wax aan caadi ahayn, mashiinka waa in la joojiyaa si loo ogaado sababta oo loo tirtiro.
8. Markaad rakibayso, fiiro gaar ah u yeelo goobta siliga goynta matoorka (eeg sawirka 2). Marka dhuumaha biyuhu ay yihiin tuubo bir ah, ka soo hoggaami xajinta madaxa ceelka; marka tuubada biyuhu ay tahay tuubo caag ah, ka soo jiid calaamadda dhulka ee bamka korontada.

According to the product description, our submersible pump after installation needs careful inspection and testing to ensure its normal operation and prolong the service life. After installation, it is necessary to recheck the insulation resistance and three-phase continuity to ensure that the instrument and the start-up equipment are connected correctly. Before starting the test machine, observe whether the indication readings of the instruments are correct, check whether the rated voltage and current specified on the nameplate are exceeded, and observe whether there is noise or vibration in the pump. If everything is normal, it can be put into operation. After the pump runs for the first four hours, the motor thermal insulation resistance should be closed and quickly tested, and its value should not be less than 0.5 megaohms. After stopping the pump, it needs to be restarted at an interval of five minutes to prevent the water column in the pipeline from returning to cause the motor to burn out due to excessive current. After normal operation, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. Once abnormal conditions are found, such as the current exceeds 20% of the rated working conditions, the water level drops causing intermittent drainage, the submersible pump vibrates or makes loud noise, the supply voltage is lower than 340 volts, one phase in the fuse is burned out, the water pipe is damaged or the motor's thermal insulation resistance to the earth is less than 0.5 megaohms, the machine should be stopped immediately to eliminate the fault. When disassembling the unit, it is necessary to operate in accordance with the specified sequence to avoid damaging various components. Once a year or less than one year of use but has been immersed for two years, it must be disassembled and inspected in accordance with the provisions, and the worn parts must be replaced to ensure the normal operation and service life of the submersible electric pump.

 1, dami biyaha godka matoorka (gaar ahaan xilliga jiilaalka si aad uga hortagto matoorku baraf), oo si fiican u xidh fiilada.

 2, ku kaydi qol gudaha ah oo aan lahayn walxo daxalaystay iyo gaas, kulaylkiisuna ka hooseeyo 40 °C.

 3, isticmaalka muddada dheer waa in fiiro gaar ah u leh ka hortagga miridhku ee matoorada submersible.

01 Qaadashada biyaha ceelka qoto dheer

02 Biyo-helid-sare

03 biyaha buuraha 

04 munaaradaha biyaha

05 waraabka beeraha

06 waraabka beerta

07 qaadashada biyaha webiga

08 biyaha guriga