200QJP Peep Well Submerable Pump

QJP series special fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are covered with alloy copper sleeve as lubricant, using water. Stainless steel sleeves replace ball bearings, avoiding the problem of easy rust of ball bearings and the problem of motor burning due to lack of oil wear. It is very suitable for music fountain, all models can be used horizontally.

This product uses three-phase AC 380V power supply (tolerance + 5%), 50HZ frequency (tolerance + 1%); the applicable water quality conditions for water temperature is not higher than 20 °C, solid impurities content (mass ratio) is not more than 0.01%, pH value (pH) is 6.5-8.5, hydrogen sulfide content is not more than 1.5mg/L, chloride ion content is not more than 400mg/L. The motor adopts closed or water sealed wet structure, before use must be filled with clean water to prevent virtual filled, and then tighten the water injection and air exhaust bolts, otherwise not to use. Submersible pump must be completely immersed in water to work, immersion depth shall not exceed 70 meters, the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The water in the well should be able to meet the water output and continuous operation of the submersible pump, the water output of the pump should be controlled at 0.7-1.2 times the rated flow. The well should be kept vertical, the submersible pump can not be used horizontally or overturned, only vertical installation. The submersible pump must be equipped with cables as required, and equipped with external overload protection device. The pump is strictly prohibited from no water load test.

 Well submersible pump is a kind of fresh water pump, it is strictly prohibited to dig new wells and pump mud and sand. The product adopts 380/50HZ voltage grade, other voltage grades shall not be used, and the submersible motor needs to be customized. Underground cables must use waterproof cables, and must be equipped with starting equipment, such as distribution box, etc. The starting equipment shall have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and no-load protection, etc. In abnormal cases, the protection device shall be tripped in time. When installed and used, the pump must be reliably grounded, it is prohibited to push and pull the switch when hands and feet are wet, and the power supply must be cut off before installation and maintenance of the pump. In the place where the pump is used, an obvious "anti-electric shock" sign must be set up. Before going down the well or installing, the motor must be filled with distilled water or non-corrosive clean cold water, and the water adding/discharge bolts must be tightened. When testing the pump on the ground, water must be injected into the pump chamber to lubricate the rubber bearings. The instantaneous start time shall not exceed one second to check whether the steering is correct, pay attention to safety, and prevent the pump from toppling and injuring people when it is upright. In strict accordance with the specified lift and flow range of the pump, to prevent the pump in low lift with large flow or in high lift with large traction, resulting in extreme wear of thrust bearings and other components, the motor overload and burn. After the pump into the well, the motor to the ground insulation resistance should be measured not less than 100MΩ. After the start, regular observation of voltage and current, and check whether the motor winding insulation meets the requirements; if the location of the pump storage temperature below freezing, should discharge the water in the motor cavity, to prevent water in the motor cavity ice and damage the motor due to low temperature.

Soo bandhigid kooban ee qaab dhismeedka: qaybta bamka waxay inta badan ka kooban tahay usheeda dhexe ee bamka, impeller, qolof leexinta, caag, jeegaga jidhka (qaybaha ikhtiyaariga ah) iyo qaybaha kale. Qaybta mooto waxay inta badan ka kooban tahay saldhigga, filimka xakamaynaya cadaadiska, riixitaanka, saxanka riixida. , Kursiga hagaha hoose ee hagaha, stator, rotor, kursiga hagaha sare ee hagaha, giraanta ciidda, qaybta gelitaanka biyaha, fiilada iyo qaybaha kale.

Tilmaamaha ugu muhiimsan ee alaabta waxaa ka mid ah:

 1, Matoorku waa matoor saddex-waji ah oo aan caadi ahayn oo qoyan oo qoyan, godka matoorka waxaa ka buuxa biyo nadiif ah, oo loo isticmaalo in lagu qaboojiyo matoorka oo lagu subiyo xajinta, filimka xakamaynta cadaadiska ee hoose ee matoorka ayaa loo isticmaalaa in lagu hagaajiyo. kala duwanaanshaha cadaadiska balaadhinta iyo foosha ee biyaha gudaha jidhka oo ay sababtay isbeddelka heerkulka sare u kaca ee matoorka.

 2, Si aan ciidda ceelka biyaha ku jirta uga dhicin matoorka, qaybta sare ee shafka matoorka waxaa lagu rakibay laba shaabad oo saliid ah, waxaana lagu rakibay giraan ciid si loo sameeyo qaab-dhismeed ka hortagga ciidda.

 3, Si looga hortago in bamka bamka uu kor u kaco marka la bilaabayo, bamka bamka iyo matoorka ayaa ku xiran isku-xirnaanta, waxaana lagu dhejiyaa tuubada sare ee qaybta hoose ee matoorka.

 4, Saliidda matoorka iyo bamka xajinta waa saliidda biyaha.

 5, Dabaylaha stator motor ka samaysan yahay silig motor submersible tayo sare leh, oo leh waxqabadka dahaarka sare.

 6, Bamka waxaa loogu talagalay kombuyuutar CAD, oo leh qaab-dhismeed fudud iyo waxqabad farsamo oo wanaagsan.

(1) Diyaarinta ka hor inta aan la rakibin:
1. Hubi in bamka hoos mara uu buuxiyo shuruudaha isticmaalka iyo baaxadda lagu sheegay buug-gacmeedka.
2. Adigoo isticmaalaya dhexroor culus oo leh dhexroor la mid ah dhexroorka dibadda ee ugu sarreeya ee bamka hoos mara, cabbir haddii dhexroorka ceelka ceelka uu ku habboon yahay bamka hoos mara, cabbirna haddii qoto-dheeraanta ceelku buuxinayo shuruudaha rakibidda.
3. Hubi in ceelka ceelku uu nadiif yahay iyo in biyuhu ceelku yihiin kuwo gurracan. Weligaa ha isticmaalin bam koronto oo hoos iman kara si aad u dhaqdo bamka weriyaha dhoobada iyo biyaha ciidda si aad uga fogaato dhaawac degdeg ah oo soo gaadha bamka korontadu hoos u dhigto.
4. Hubi in booska xajinaha welhead ku habboon yahay iyo haddii ay u adkeysan karto tayada unugga oo dhan
5. Hubi in qaybaha matoorka hoos u dhigi karaan ay dhammaystiran yihiin oo si sax ah loo rakibay si waafaqsan jaantuska kulanka ee buug-gacmeedka, ka saar shaashadda oo beddel isku-xidhka si aad u aragto inay si dabacsan u wareegayso.
6. Ka fur furka biyaha oo ka buuxi godka matoorka biyo nadiif ah oo aan daxalaysan (xusuusnow in aad buuxiso), ka bacdina adkee xadhigga biyaha. Ka dib 12 saacadood oo duritaanka biyaha ah, caabbinta dahaarka ee matoorku waa in aanu ka yarayn 150M Q marka lagu cabbiro miis gariir 500V ah.
7. Isku-xidhka fiilada, ka jar caag 120mm ah oo ka mid ah daraf ka mid ah fiilada baxaysa iyo fiilada ku habboon ee leh mindi koronto-yaqaanka ka dibna ku rogrogmadaa dhererka saddexda fiilooyinka xudunta ah ee qaab go'an, ka saar xudunta 20mm naxaas ah, xoqin oksaydhka lakabka dibadda ee fiilada naxaasta leh mindi ama maro ciid, oo geli labada silig ee isku xidhan ee ku dhammaanaya palirs. Ka dib markaad lakabka si adag ugu xidho silig naxaas ah, si fiican oo adag u iibi, iyo ciid kasta. oogada dushiisa. Dabadeed, saddexda qaybood ee kala-goysyada, isticmaal cajaladda daboolka polyvester-ka si aad ugu duubto qaab nus ah oo isku xiran oo ah saddex berkedood. Ku duub labada daraf ee lakabka wax lagu duubo si adag adigoo isticmaalaya dunta nyion, ka dibna isticmaal qaab nus ah oo la tumay si aad ugu duubto cajaladda saddex lakab. Ku duub daboolka dibadda cajaladda daboolka cadaadiska sare ee saddex lakab. Ugu dambeyntii, isku laab saddexda xargo oo si isdaba joog ah ugu duub shan lakab oo leh cajalad cadaadis sare leh. Lakab kasta waa in si adag loo xidhaa, kala-goysyada is-dhexyaaca waa inay ahaadaan kuwo adag oo fim ah si ay uga hortagaan in biyuhu soo galaan oo waxyeello u geystaan ​​dahaarka. , kaas oo aan ka yarayn 100M Ω

Jaantuska habka fiilooyinka fiilooyinka ee ku lifaaqan waa sida soo socota:

8. Isticmaal multimeter-ka si aad u hubiso in xadhkaha saddexda weji ay isku xidhan yihiin iyo in iska caabbinta DC-ku ay qiyaas ahaan dheelli tiran yihiin.
9. Hubi in awoodda wareegga iyo beddelka ay si xad dhaaf ah u raran yihiin, ka dibna ku xidh furaha ilaalinta culayska ama qalabka bilowga. Ka eeg Shaxda 2 noocyo gaar ah, ka dibna ku shub baaldi biyo ah bamka biyaha ee ka soo baxa bamka biyaha si aad u saliidayn xadhkaha caagga ah ee bamka, ka dibna bamka korontadu hoos u dhigto dhig mid toosan oo joogto ah. Bilow (wax aan ka badnayn hal ilbiriqsi) oo hubi in jihada isteerinka ay waafaqsan tahay calaamadda isteerinka. Haddaysan ahayn, ku beddel laba xidhiidhiye oo ka mid ah fiilada saddexda weji leh. Kaddib rakib shaandhada una diyaari inaad ceelka dhaadhacdo. Haddii loo isticmaalo waqtiyo gaar ah (sida godadka, godadka, webiyada, balliyada, balliyada, iwm.), bamka korontadu waa in si la isku halleyn karo loo dejiyo.

(2) Qalabka iyo qalabka lagu rakibo:
1. Hal ka mid ah silsiladaha wax-qaadista ee ka badan laba tan.
2. Sadex geesood ah oo leh joog toosan oo aan ka yarayn afar mitir.
3. Laba xadhig oo ka laadlaad ah oo qaadi kara miisaan ka badan hal tan (waxay qaadi karaan culayska bambooyin biyo ah oo dhammaystiran).
4. Ku rakib laba-labo oo xajin ah (kabyo).
5. Biraha, dubbaha, kaashawiito, qalabka korontada iyo qalabka, iwm.

(3) Ku rakibida bamka korontada
1. Jaantuska rakibaadda ee bamka korontada hoostiisa ayaa lagu muujiyay Jaantuska 2. Cabbirrada rakibidda gaarka ah ayaa lagu muujiyay shaxda 3 "Liiska Cabbirrada Rakibaadda ee Bamka Korontada ee Submersible".

2. Bambooyin koronto oo hoos yimaada oo madax ka yar 30 mitir ayaa si toos ah loogu shubi karaa ceelka iyadoo la isticmaalayo tubooyinka iyo xargaha ama xargaha kale ee hemp kuwaas oo qaadi kara miisaanka buuxa ee dhammaan mishiinka, tuubooyinka biyaha, iyo biyaha tuubooyinka.

3. Bambooyin leh madax ka badan 30 mitir ayaa isticmaala tubooyinka birta, nidaamka rakibiddana waa sida soo socota.
①Isticmaal xajin si aad ugu xidho cidhifka sare ee qaybta matoorka biyaha (matoorka iyo bamka biyaha ayaa ku xidhan wakhtigan), ku qaad silsilad ka laadlaadsan, oo si tartiib ah ugu xidh ceelka ilaa aad xajinayso madaxa ceelka oo ka saar silsilad laadlaadsan.
② Isticmaal labo xajin oo kale si aad tuubada ugu xajiso, ku qaad silsilad laadlaad ah oo 15 cm ka fog garabka, oo si tartiib ah hoos ugu dhig. Inta u dhaxaysa flange tuubada iyo bamka bamka, dhig suufka caagga ah meesha oo adkee tuubada oo si siman ugu bamgareyso boolal, lawska iyo weelasha guga.
③ Xoogaa kor u qaad bamka hoos mara, ka saar xajinta cidhifka sare ee bamka biyaha, si adag ugu xidh fiilada tuubada biyaha cajalad balaastik ah, oo si tartiib ah hoos ugu xidh ilaa xajinta la dhigo madaxa ceelka.
④ Isticmaal isku qaab si aad ugu xidhid dhammaan tuubooyinka biyaha ceelka.
⑤Kadib markii fiilada macdanta "lead-out" lagu xiro furaha kantaroolka, waxay ku xiran tahay sahayda korontada ee saddexda weji.

(4) Waxyaabaha la xuso marka la rakibayo:
1. Haddi dhacdo isku buuqid ah la helo inta lagu jiro habka bamgareynta, leexi ama jiid tuubada biyaha si aad uga gudubto meesha saxmada leh. Haddii tillaabooyin kala duwani aanay weli shaqayn, fadlan ha ku qasbin bamka si aad uga fogaato burbur ku yimaadda bamka korontada ee hoos u dhigi kara iyo ceelka.
2. Inta lagu jiro rakibidda, suufka caagga ah waa in lagu dhejiyaa gees ka gees kasta oo tuubo ah oo la adkeeyo si siman.
3. Marka bamka biyaha lagu shubo ceelka waa in la dhex dhigaa dhuunta ceelka badhtankeeda si aanay bamku ugu socon darbiga ceelka muddo dheer, taasina ay keento in bamku gariiro oo matoorku xaaqo oo gubato. .
4. Go'aami qoto dheeraanta bamka biyaha ilaa gunta ceelka iyadoo loo eegayo ciidda qulqulaya iyo xaaladaha ciidda ee ceelka. Ha ku aasin bamka dhoobada. Masaafada u jirta bamka biyaha ilaa gunta ceelka guud ahaan waa mid aan ka yarayn 3 mitir (eeg sawirka 2).
5. Moolka gelitaanka biyaha ee bamka biyuhu waa in aanu ka yarayn 1-1.5 mitir heerka biyaha firfircoon ilaa marinka biyaha gelitaanka (eeg sawirka 2). Haddii kale, xadhkaha matoorka biyaha ayaa si fudud u dhaawacmi kara.
6. Wiishka bamka biyuhu ma noqon karo mid aad u hooseeya. Haddii kale, waxaa loo baahan yahay in lagu rakibo tuubada biyaha ee albaabka ceelka si loo xakameeyo socodka bamka ee barta socodka lagu qiimeeyay si looga hortago in matoorku uu si xad dhaaf ah u raro oo uu u gubto heerka socodka badan ee socodka awgeed.
7. Marka bamka biyuhu socdo, wax-soo-saarka biyuhu waa inuu ahaado mid joogto ah oo xitaa, hadda waa inuu ahaado mid deggan (marka la qiimeeyo xaaladaha shaqada, guud ahaan wax aan ka badnayn 10% ee hadda la qiimeeyay), waana inaysan jirin gariir ama buuq. Haddii ay jiraan wax aan caadi ahayn, mashiinka waa in la joojiyaa si loo ogaado sababta oo loo tirtiro.
8. Markaad rakibayso, fiiro gaar ah u yeelo goobta siliga goynta matoorka (eeg sawirka 2). Marka dhuumaha biyuhu ay yihiin tuubo bir ah, ka soo hoggaami xajinta madaxa ceelka; marka tuubada biyuhu ay tahay tuubo caag ah, ka soo jiid calaamadda dhulka ee bamka korontada.

• 1.Ka dib markii bamka submersible la rakibo, hubi caabbinta dahaarka iyo conduction saddex-waji ka furaha mar kale, hubi in qalabka iyo isku xirka qalabka bilowga ah waa khalad, haddii aysan jirin wax dhibaato ah, mishiinka tijaabada waa la bilaabi karaa. oo fiirso in akhrinta tusaha qalabku uu ka badan yahay tamarta la qiimeeyay iyo hadda ee lagu cayimay taarikada bilawga ka dib, oo fiirso bal in bamku leeyahay buuq iyo ifafaale gariir, oo la hawlgalo haddii wax walba caadi yihiin.
• 2.Ka dib markii hawlgalka ugu horreeya ee bamka muddo afar saacadood ah, matoorka waa in la xiro si loo tijaabiyo caabbinta kuleylka kuleylka si dhakhso ah, qiimihiisuna waa inuusan ka yarayn 0.5 megaohm.
• 3.Ka dib marka bamka la xiro, waa in la bilaabo shan daqiiqo ka dib si looga hortago in tiirarka biyaha ee tuubada ay si buuxda u soo qulqulaan oo ay keento dhaqdhaqaaq xad dhaaf ah iyo gubasho.
• 4.Ka dib markii bamka la geliyo hawlgalka caadiga ah, si loo kordhiyo nolosheeda adeegga, waxaa lagama maarmaan ah in la hubiyo in tamarta sahayda, hadda shaqaynaysa iyo caabbinta dahaadhka ay caadi yihiin si joogto ah. Haddii shuruudahan soo socda la helo, bamka waa in isla markiiba la xidhaa si cilad looga qaado.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Heerka biyaha firfircooni wuxuu hoos ugu dhacaa qaybta biyaha soo gelista, taasoo keenaysa biyo kala go'a.
• 3 Bamka hoos mara waxa uu leeyahay gariir ama buuq daran.
• 4 Danab sahaydu waxa ay ka hoosaysaa 340 volts.
• 5 Fiyuus baa gubtay.
• 6 Dhuumaha biyaha ayaa dhaawacmay.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1.Untie the cable tie, remove the pipeline part, and remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 This product is a submersible pump, which is suitable for various water areas, such as home, agriculture and industry.In order to prevent the motor from freezing in winter, be sure to discharge all the water in the pump chamber, and roll and tie the cable well.In addition, a room without corrosive substances and gases and with a temperature below 40 °C should be selected for storage.When not in use for a long time, special attention should be paid to the rust prevention of the submersible pump.This product is exquisitely designed and convenient to use, which can help users efficiently deal with various water needs, and is an ideal choice for your home and industrial water.

01 Qaadashada biyaha ceelka qoto dheer

02 Biyo-helid-sare

03 biyaha buuraha

04 munaaradaha biyaha

05 waraabka beeraha

06 waraabka beerta

07 qaadashada biyaha webiga

08 biyaha guriga