250QJP Peep Well Submerable Pump

This series of fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are equipped with alloy copper sleeves with water as lubricant. Stainless steel bushings replace ball bearings, avoiding the problems of easy rust of ball bearings and burnout of motor due to lack of oil and wear. Most suitable for music fountain, all models can be used horizontally.

1, Korontada: saddex-waji AC 380V (dulqaad +/- 5%), 50HZ (dulqaad +/- 1%).

2, tayada biyaha:

(1) heerkulka biyuhu kama sarreyn 20 °C;

(2) Waxyaabaha wasakhda adag ku jira (samiga baaxadda) kama badna 0.01%;

(3) Qiimaha PH (pH) 6.5-8.5;

(4) Waxa ku jira hydrogen sulfide kama badna 1.5mg/L;

(5) Waxa ku jira chloride ion kama badna 400mg/L.

3, matoorku waa xiran yahay ama qaab-dhismeedka qoyan ee biyaha ka buuxsamay, ka hor inta aan la isticmaalin godka matoorka submersible waa in ay ka buuxaan biyo nadiif ah, si looga hortago been buuxda, ka dibna adkeeyo duritaanka biyaha, boolal sii daayo hawada, haddii kale loo ogol yahay in la isticmaalo.

4, bamka hoos u dhiga biyaha waa in gabi ahaanba la geliyo biyaha, qoto dheer oo quusin ah oo aan ka badnayn 70m, gunta hoose ee matoorka hoostiisa oo aan ka yarayn 3m.

5, socodka biyaha ceelasha waa in ay awoodaan in ay la kulmaan wax soo saarka biyaha bamka hoostiisa iyo hawlgalka joogtada ah, wax soo saarka biyaha bamka hoostiisa waa in lagu xakameeyaa 0.7 - 1.2 jeer socodka la qiimeeyay.

6, Ceelku waa inuu toosan yahay, bamka submersible lama isticmaali karo ama laguma daadin karo, kaliya isticmaal toosan.

7, bamka submersible waa in lagu dhejiyaa fiilada si waafaqsan shuruudaha, iyo qalabka ilaalinta xad-dhaafka ah ee dibadda.

8, bamka si adag ayaa loo mamnuucay iyada oo aan jirin mishiinka tijaabada ah ee wax-load ah

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, si adag sida ku xusan qodobbada wiishka bamka, kala duwanaanshaha socodka isticmaalka, si looga hortago socodka hooseeya ama xoogga sare ee wiishka, xajinta iyo qaybaha kale ee xirashada, culeyska matoorka ayaa gubtay

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The introduction and structure of this pump product mainly include pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The main characteristics of this pump product include the use of water-cooled wet submersible three-phase asynchronous motor, the motor cavity is filled with clean water to cool the motor and lubricate the bearing, the pressure regulating diaphragm at the bottom is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed on the upper end of the motor shaft extension, and the sand ring is installed to form a sand prevention structure. In order to avoid the pump shaft jumping at startup, the pump shaft and the motor shaft are connected together through the coupling, and the thrust bearing is installed at the lower part of the motor. The motor and pump bearing lubrication adopts water lubrication. The stator winding of the motor adopts high quality submersible motor winding, with high insulation performance. The pump adopts computer CAD design, simple structure and superior technical performance.

(1) Diyaarinta ka hor inta aan la rakibin:
1. Hubi in bamka hoos mara uu buuxiyo shuruudaha isticmaalka iyo baaxadda lagu sheegay buug-gacmeedka.
2. Adigoo isticmaalaya dhexroor culus oo leh dhexroor la mid ah dhexroorka dibadda ee ugu sarreeya ee bamka hoos mara, cabbir haddii dhexroorka ceelka ceelka uu ku habboon yahay bamka hoos mara, cabbirna haddii qoto-dheeraanta ceelku buuxinayo shuruudaha rakibidda.
3. Hubi in ceelka ceelku uu nadiif yahay iyo in biyuhu ceelku yihiin kuwo gurracan. Weligaa ha isticmaalin bam koronto oo hoos iman kara si aad u dhaqdo bamka weriyaha dhoobada iyo biyaha ciidda si aad uga fogaato dhaawac degdeg ah oo soo gaadha bamka korontadu hoos u dhigto.
4. Hubi in booska xajinaha welhead ku habboon yahay iyo haddii ay u adkeysan karto tayada unugga oo dhan
5. Hubi in qaybaha matoorka hoos u dhigi karaan ay dhammaystiran yihiin oo si sax ah loo rakibay si waafaqsan jaantuska kulanka ee buug-gacmeedka, ka saar shaashadda oo beddel isku-xidhka si aad u aragto inay si dabacsan u wareegayso.
6. Ka fur furka biyaha oo ka buuxi godka matoorka biyo nadiif ah oo aan daxalaysan (xusuusnow in aad buuxiso), ka bacdina adkee xadhigga biyaha. Ka dib 12 saacadood oo duritaanka biyaha ah, caabbinta dahaarka ee matoorku waa in aanu ka yarayn 150M Q marka lagu cabbiro miis gariir 500V ah.
7. Isku-xidhka fiilada, ka jar caag 120mm ah oo ka mid ah daraf ka mid ah fiilada baxaysa iyo fiilada ku habboon ee leh mindi koronto-yaqaanka ka dibna ku rogrogmadaa dhererka saddexda fiilooyinka xudunta ah ee qaab go'an, ka saar xudunta 20mm naxaas ah, xoqin oksaydhka lakabka dibadda ee fiilada naxaasta leh mindi ama maro ciid, oo geli labada silig ee isku xidhan ee ku dhammaanaya palirs. Ka dib markaad lakabka si adag ugu xidho silig naxaas ah, si fiican oo adag u iibi, iyo ciid kasta. oogada dushiisa. Dabadeed, saddexda qaybood ee kala-goysyada, isticmaal cajaladda daboolka polyvester-ka si aad ugu duubto qaab nus ah oo isku xiran oo ah saddex berkedood. Ku duub labada daraf ee lakabka wax lagu duubo si adag adigoo isticmaalaya dunta nyion, ka dibna isticmaal qaab nus ah oo la tumay si aad ugu duubto cajaladda saddex lakab. Ku duub daboolka dibadda cajaladda daboolka cadaadiska sare ee saddex lakab. Ugu dambeyntii, isku laab saddexda xargo oo si isdaba joog ah ugu duub shan lakab oo leh cajalad cadaadis sare leh. Lakab kasta waa in si adag loo xidhaa, kala-goysyada is-dhexyaaca waa inay ahaadaan kuwo adag oo fim ah si ay uga hortagaan in biyuhu soo galaan oo waxyeello u geystaan ​​dahaarka. , kaas oo aan ka yarayn 100M Ω

Jaantuska habka fiilooyinka fiilooyinka ee ku lifaaqan waa sida soo socota:

8. Isticmaal multimeter-ka si aad u hubiso in xadhkaha saddexda weji ay isku xidhan yihiin iyo in iska caabbinta DC-ku ay qiyaas ahaan dheelli tiran yihiin.
9. Hubi in awoodda wareegga iyo beddelka ay si xad dhaaf ah u raran yihiin, ka dibna ku xidh furaha ilaalinta culayska ama qalabka bilowga. Ka eeg Shaxda 2 noocyo gaar ah, ka dibna ku shub baaldi biyo ah bamka biyaha ee ka soo baxa bamka biyaha si aad u saliidayn xadhkaha caagga ah ee bamka, ka dibna bamka korontadu hoos u dhigto dhig mid toosan oo joogto ah. Bilow (wax aan ka badnayn hal ilbiriqsi) oo hubi in jihada isteerinka ay waafaqsan tahay calaamadda isteerinka. Haddaysan ahayn, ku beddel laba xidhiidhiye oo ka mid ah fiilada saddexda weji leh. Kaddib rakib shaandhada una diyaari inaad ceelka dhaadhacdo. Haddii loo isticmaalo waqtiyo gaar ah (sida godadka, godadka, webiyada, balliyada, balliyada, iwm.), bamka korontadu waa in si la isku halleyn karo loo dejiyo.

(2) Qalabka iyo qalabka lagu rakibo:
1. Hal ka mid ah silsiladaha wax-qaadista ee ka badan laba tan.
2. Sadex geesood ah oo leh joog toosan oo aan ka yarayn afar mitir.
3. Laba xadhig oo ka laadlaad ah oo qaadi kara miisaan ka badan hal tan (waxay qaadi karaan culayska bambooyin biyo ah oo dhammaystiran).
4. Ku rakib laba-labo oo xajin ah (kabyo).
5. Biraha, dubbaha, kaashawiito, qalabka korontada iyo qalabka, iwm.

(3) Ku rakibida bamka korontada
1. Jaantuska rakibaadda ee bamka korontada hoostiisa ayaa lagu muujiyay Jaantuska 2. Cabbirrada rakibidda gaarka ah ayaa lagu muujiyay shaxda 3 "Liiska Cabbirrada Rakibaadda ee Bamka Korontada ee Submersible".

2. Bambooyin koronto oo hoos yimaada oo madax ka yar 30 mitir ayaa si toos ah loogu shubi karaa ceelka iyadoo la isticmaalayo tubooyinka iyo xargaha ama xargaha kale ee hemp kuwaas oo qaadi kara miisaanka buuxa ee dhammaan mishiinka, tuubooyinka biyaha, iyo biyaha tuubooyinka.

3. Bambooyin leh madax ka badan 30 mitir ayaa isticmaala tubooyinka birta, nidaamka rakibiddana waa sida soo socota.
①Isticmaal xajin si aad ugu xidho cidhifka sare ee qaybta matoorka biyaha (matoorka iyo bamka biyaha ayaa ku xidhan wakhtigan), ku qaad silsilad ka laadlaadsan, oo si tartiib ah ugu xidh ceelka ilaa aad xajinayso madaxa ceelka oo ka saar silsilad laadlaadsan.
② Isticmaal labo xajin oo kale si aad tuubada ugu xajiso, ku qaad silsilad laadlaad ah oo 15 cm ka fog garabka, oo si tartiib ah hoos ugu dhig. Inta u dhaxaysa flange tuubada iyo bamka bamka, dhig suufka caagga ah meesha oo adkee tuubada oo si siman ugu bamgareyso boolal, lawska iyo weelasha guga.
③ Xoogaa kor u qaad bamka hoos mara, ka saar xajinta cidhifka sare ee bamka biyaha, si adag ugu xidh fiilada tuubada biyaha cajalad balaastik ah, oo si tartiib ah hoos ugu xidh ilaa xajinta la dhigo madaxa ceelka.
④ Isticmaal isku qaab si aad ugu xidhid dhammaan tuubooyinka biyaha ceelka.
⑤Kadib markii fiilada macdanta "lead-out" lagu xiro furaha kantaroolka, waxay ku xiran tahay sahayda korontada ee saddexda weji.

(4) Waxyaabaha la xuso marka la rakibayo:
1. Haddi dhacdo isku buuqid ah la helo inta lagu jiro habka bamgareynta, leexi ama jiid tuubada biyaha si aad uga gudubto meesha saxmada leh. Haddii tillaabooyin kala duwani aanay weli shaqayn, fadlan ha ku qasbin bamka si aad uga fogaato burbur ku yimaadda bamka korontada ee hoos u dhigi kara iyo ceelka.
2. Inta lagu jiro rakibidda, suufka caagga ah waa in lagu dhejiyaa gees ka gees kasta oo tuubo ah oo la adkeeyo si siman.
3. Marka bamka biyaha lagu shubo ceelka waa in la dhex dhigaa dhuunta ceelka badhtankeeda si aanay bamku ugu socon darbiga ceelka muddo dheer, taasina ay keento in bamku gariiro oo matoorku xaaqo oo gubato. .
4. Go'aami qoto dheeraanta bamka biyaha ilaa gunta ceelka iyadoo loo eegayo ciidda qulqulaya iyo xaaladaha ciidda ee ceelka. Ha ku aasin bamka dhoobada. Masaafada u jirta bamka biyaha ilaa gunta ceelka guud ahaan waa mid aan ka yarayn 3 mitir (eeg sawirka 2).
5. Moolka gelitaanka biyaha ee bamka biyuhu waa in aanu ka yarayn 1-1.5 mitir heerka biyaha firfircoon ilaa marinka biyaha gelitaanka (eeg sawirka 2). Haddii kale, xadhkaha matoorka biyaha ayaa si fudud u dhaawacmi kara.
6. Wiishka bamka biyuhu ma noqon karo mid aad u hooseeya. Haddii kale, waxaa loo baahan yahay in lagu rakibo tuubada biyaha ee albaabka ceelka si loo xakameeyo socodka bamka ee barta socodka lagu qiimeeyay si looga hortago in matoorku uu si xad dhaaf ah u raro oo uu u gubto heerka socodka badan ee socodka awgeed.
7. Marka bamka biyuhu socdo, wax-soo-saarka biyuhu waa inuu ahaado mid joogto ah oo xitaa, hadda waa inuu ahaado mid deggan (marka la qiimeeyo xaaladaha shaqada, guud ahaan wax aan ka badnayn 10% ee hadda la qiimeeyay), waana inaysan jirin gariir ama buuq. Haddii ay jiraan wax aan caadi ahayn, mashiinka waa in la joojiyaa si loo ogaado sababta oo loo tirtiro.
8. Markaad rakibayso, fiiro gaar ah u yeelo goobta siliga goynta matoorka (eeg sawirka 2). Marka dhuumaha biyuhu ay yihiin tuubo bir ah, ka soo hoggaami xajinta madaxa ceelka; marka tuubada biyuhu ay tahay tuubo caag ah, ka soo jiid calaamadda dhulka ee bamka korontada.

 After the installation of the underwater pump, the insulation resistance and three-phase continuity of the switch face should be rechecked, and the connection between the instrument and the start device should be checked for any errors. If there is no problem, you can start to test the machine. After the start, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump has noise or vibration. If everything is normal, it can be put into operation. After the first operation of the pump for four hours, the motor should be shut down and tested for thermal insulation resistance quickly. Its value should not be less than 0.5 megaohm. After stopping the pump, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing and causing the motor to burn out due to excessive current. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, running current and insulation resistance are normal. If the following conditions are found, the machine should be shut down immediately to eliminate the fault: the current exceeds 20% under rated working conditions; the dynamic water level drops to the inlet section, resulting in intermittent drainage; the underwater pump becomes violently vibrating or making noise; the supply voltage is lower than 340 volts; a fuse is blown out; the water pipe is damaged; the motor's thermal insulation resistance to the earth is less than 0.5 megaohm. The sequence of disassembly is: untie the cable fastening, remove the pipeline part, remove the line protection plate, screw down the water discharge bolt and discharge all the water in the motor chamber, remove the filter and loosen the coupling fixing screw of the motor shaft. The sequence of disassembly of the pump is: (see Figure 1) inlet section, impeller, guide housing, impeller, check the valve body. When removing the impeller, use special tools to loosen the taper sleeve of the impeller. Avoid bending the pump shaft and damaging the components throughout the process. The disassembly process of the motor is: (see Figure 1) put the motor on the platform, and remove the bolts, base, shaft head lock nut, thrust plate, key, lower guide plate (transverse bolt), bearing seat, screw knife seat from the bottom of the motor in order (take care not to damage the winding), and finally remove the connecting part and the upper guide bearing seat. Before assembling the unit, the rust and dirt of each part should be cleaned, and the sealant should be applied to each mating surface and fastener, and then assembled in reverse order of disassembly (the movement of the motor shaft after assembly is about one millimeter). After assembly, the coupling should be rotated flexibly and put on the filter for test. Once a year, or if less than a year of operation but has been immersed for two years, the underwater electric pump must be disassembled for maintenance in accordance with Article 5 and replace worn parts to ensure the normal operation and durability of the pump.

 1, dami biyaha godka matoorka (gaar ahaan xilliga jiilaalka si aad uga hortagto matoorku baraf), oo si fiican u xidh fiilada.

 2, ku kaydi qol gudaha ah oo aan lahayn walxo daxalaystay iyo gaas, kulaylkiisuna ka hooseeyo 40 °C.

 3, isticmaalka muddada dheer waa in fiiro gaar ah u leh ka hortagga miridhku ee matoorada submersible.

01 Qaadashada biyaha ceelka qoto dheer

02 Biyo-helid-sare

03 biyaha buuraha 

04 munaaradaha biyaha

05 waraabka beeraha

06 waraabka beerta

07 qaadashada biyaha webiga

08 biyaha guriga