150QJB Zurfin Rijiya Mai Ruwa Mai Ruwa

The motor winding adopts special water-resistant wire for frequency conversion winding, which has excellent characteristics such as high frequency stamping resistance, pulse peak voltage stamping resistance and high temperature aging resistance. The frequency conversion winding design ensures the long-term stable conversion operation of the motor between 1HZ-50HZ, making the frequency conversion deep well pump more energy saving and longer service life.

The product is supplied by three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%). Applicable water quality conditions include water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not more than 1.5mg/L, chloride ion content is not more than 400mg/L. The motor adopts closed or water-filled wet structure. Before use, the internal chamber needs to be filled with clean water to prevent virtual filling. The pump needs to be completely immersed in water, the penetration depth shall not exceed 70m, and the distance from the bottom of the well shall not be less than 3m. The water inlet of the well shall meet the water output and continuous operation requirements of the pump, and the output of the pump shall be controlled at 0.7-1.2 times of the rated flow. The pump shall be used vertically, and the pump must be matched with the cable according to the requirements and equipped with external overload protection device. It is strictly prohibited to conduct no-load test of the pump, and it is necessary to avoid operation without water.

This well submersible pump is a pump suitable for clean water. It is strictly prohibited to pump sediment and turbid water in new wells. The voltage level of the pump is 380/50HZ. Other voltage levels of the submersible motor need to be customized. Underground cables must be waterproof and must be equipped with starting equipment, such as distribution box, etc. The starting equipment should have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and idling protection, etc. Under abnormal circumstances, the protection device should be tripped in time. In the process of installation and use, the pump must be reliably grounded. It is prohibited to push and pull the switch when the hands and feet are wet. The power must be cut off before installation and maintenance of the pump. The place where the pump is used must set up a clear "anti-electric shock" mark. Before going down the well or installation, the motor must be filled with distilled water or non-corrosive cool water, and the water inlet and outlet screws must be tightened. When testing the pump, water must be injected into the pump chamber to lubricate the rubber bearings. The instant start shall not exceed one second to check whether the direction is correct. It is necessary to pay attention to the safety of the pump when it is erected to prevent it from toppling and hurting people. Strictly in accordance with the provisions of the pump lift and flow range of use, so as not to have a large flow in the low lift pump or a large pull in the high lift, causing extreme wear of thrust bearings and other components, resulting in motor overload burn. After the pump into the well, the measurement of the motor and ground insulation resistance, not less than 100M. After the start, regular observation of voltage and current, and check whether the motor winding insulation meets the requirements; if the pump storage location temperature is below freezing, storage should discharge the water in the motor cavity, to prevent the water in the motor cavity due to low temperature and freeze damage the motor.

Brief gabatarwar tsarin: famfo part aka yafi hada da famfo shaft, impeller, karkatar da harsashi, roba hali, duba bawul jiki (na zaɓi sassa) da sauran aka gyara. Bangaren motar ya ƙunshi tushe, fim mai daidaita matsa lamba, ɗaukar nauyi, farantin turawa, wurin zama mai jagorar ƙasa, stator, rotor, wurin zama mai jagora na sama, zoben yashi, sashin shigar ruwa, kebul da sauran abubuwan haɗin gwiwa.

Babban fasali na samfurin sun haɗa da:

1.The motor is a water-filled wet submersible three-phase asynchronous motor, the motor cavity is full of clean water, used to cool the motor and lubricate the bearing, the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the water inside the body caused by the change of the temperature rise of the motor.

2.In order to prevent the sand in the well water from entering the motor, the upper end of the motor shaft is equipped with two oil seals, and a sand ring is installed to form a sand prevention structure.

3.In order to prevent the pump shaft from running up when starting, the pump shaft and the motor shaft are connected by a coupling, and an upper thrust bearing is installed at the lower part of the motor.

4.The lubrication of the motor and the pump bearing is water lubrication.

5.The motor stator winding is made of high quality submersible motor winding wire, with high insulation performance.

6.The pump is designed by computer CAD, with simple structure and good technical performance.

(1)Shiri kafin shigarwa:
1. Bincika ko famfo mai nutsewa ya dace da yanayin amfani da iyaka da aka ƙayyade a cikin littafin.
2. Yin amfani da maɗaukaki mai nauyi tare da diamita daidai da matsakaicin matsakaicin diamita na waje na famfo, auna ko inneldimeter na rijiyar zai iya dacewa da famfo mai ruwa, kuma auna ko zurfin rijiyar ya dace da bukatun shigarwa.
3. A duba ko rijiyar tana da tsafta da kuma ko ruwan rijiyar turbude ne. Kada a taɓa amfani da famfon lantarki mai nutsewa don wanke laka na welor da ruwan yashi don gujewa lalacewa da wuri ga famfon lantarki mai nisa.
4. Bincika ko matsayin mannen shigarwa na welhead ya dace kuma ko zai iya jure ingancin duka naúrar.
5. Bincika idan kayan aikin famfo na submersible sun cika kuma an shigar dasu yadda ya kamata bisa ga zanen taron da ke cikin littafin
6. Cire dunƙule ruwa kuma cika ramin motar da ruwa mai tsabta mara lalacewa (bayanin kula. Tabbatar da cika shi), sannan ƙara matse ruwan. Bayan sa'o'i 12 na allurar ruwa, juriyar juriya na motar kada ta zama ƙasa da 150M Q lokacin da aka auna tare da tebur girgiza 500V.
7. Cable haɗin gwiwa, yanke hannun riga na 120mm na roba daga ƙarshen kebul ɗin da ke fita da kuma kebul ɗin da ya dace da wukar na'urar lantarki sa'an nan kuma ya girgiza tsawon wayoyi guda uku a cikin siffar taku, a cire wani cibiya na jan karfe 20mm, goge oxide. Layer a gefen wayar tagulla tare da wuka ko yashi, sannan a saka ƙarshen waya biyu da aka haɗa a cikin palirs.Bayan daure Layer tam tare da lallausan wayar tagulla, sayar da shi sosai da ƙarfi, da yashi kowane. burrs a saman. Sa'an nan kuma, don haɗin gwiwa guda uku, yi amfani da tef ɗin rufewa na polyvester don nannade su a cikin wani ɗan ƙaramin tsari don lafazin uku. Kunna ƙarshen Layer ɗin biyu tare da zaren nyion, sa'an nan kuma yi amfani da hanyar da aka ɗora tazara don nannade tef ɗin don yadudduka uku. Kunna fitar da waje tare da tef ɗin rufewa mai ƙarfi don yadudduka uku. A ƙarshe, ninka nau'i-nau'i uku tare kuma kunsa su akai-akai don yadudduka biyar tare da babban tef. Kowane Layer dole ne a daure sosai, kuma haɗin haɗin haɗin gwiwar dole ne su kasance masu ƙarfi kuma su kasance masu ƙarfi don hana ruwa shiga da lalata rufin, Bayan nannade, jiƙa a cikin ruwa a cikin dakin da zafin jiki na 20 'c na tsawon awanni 12, sannan a auna juriya na rufi tare da tebur mai girgiza. , wanda bai kamata ya zama ƙasa da 100M Ω ba

Jadawalin tsarin aikin wayoyi na USB wanda aka makala shine kamar haka:

8. Yi amfani da multimeter don bincika ko an haɗa wayoyi masu hawa uku kuma ko juriyar DC ta kusan daidaita.
9. Bincika ko ikon kewayawa da na'ura mai canzawa sun yi yawa, sa'an nan kuma haɗa maɓallin kariya daga overload ko kayan farawa. Dubi Table 2 don takamaiman samfura, sa'an nan kuma Zuba guga na ruwa a cikin famfo na ruwa daga tashar famfo na ruwa don sa mai da igiya na roba a cikin famfo, sa'an nan kuma sanya famfo na lantarki da ke karkashin ruwa a tsaye kuma a tsaye. Fara (ba fiye da dakika ɗaya ba) kuma duba ko jagoran tuƙi ya yi daidai da alamar tuƙi. Idan ba haka ba, musanya kowane haɗe-haɗe biyu na kebul na zamani uku. Sannan shigar da tacewa kuma shirya don gangara rijiyar. Idan aka yi amfani da shi a lokuta na musamman (kamar ramuka, ramuka, koguna, tafkuna, tafkuna, da sauransu), famfon lantarki dole ne ya zama ƙasa da dogaro.

(2) Kayan aiki da kayan aiki:
1. Ɗaya daga cikin sarƙoƙi na ɗagawa don fiye da ton biyu.
2. Tafiya mai tsayi a tsaye wanda bai gaza mita hudu ba.
3. Igiyoyin rataye guda biyu ( igiyoyin waya ) waɗanda zasu iya ɗaukar nauyin fiye da ton ɗaya (za su iya ɗaukar nauyin cikakken saitin famfo na ruwa).
4. Shigar da nau'i-nau'i biyu na manne (splints).
5. Wrenches, guduma, screwdrivers, lantarki kayan aiki da kayan aiki, da dai sauransu.

(3) Shigar da famfun lantarki:
1. Shigarwa ta hanyar yin gwajin lantarki mai saukarwa an nuna shi a cikin Hoto na 2. Ana nuna takamaiman girma a cikin Table 3 "Jerin shigarwa girma na famfo mai saukarwa".

2. Za a iya ɗaga famfunan wutar lantarki da ke ƙarƙashin ƙasa da kai ƙasa da mita 30 kai tsaye a cikin rijiyar ta hanyar amfani da tudu da igiyoyin waya ko wasu igiyoyin hemp waɗanda za su iya ɗaukar cikakken nauyin injin gabaɗaya, bututun ruwa, da ruwa a cikin bututu.

3. Pumps tare da shugaban sama da mita 30 suna amfani da bututun ƙarfe, kuma tsarin shigarwa shine kamar haka:
①A yi amfani da matsi don matse ƙarshen ɓangaren fanfo na ruwa (motar da famfon ɗin an haɗa su a wannan lokacin), ɗaga shi da sarƙar rataye, a hankali daure shi a cikin rijiyar har sai a daka matsi a kan rijiyar a cire. sarkar rataye.
② Yi amfani da wani nau'i na manne guda biyu don matsa bututu, ɗaga shi tare da sarƙar rataye 15 cm daga flange, kuma rage shi a hankali. Tsakanin flange na bututu da famfo flange Saka robar kushin a wurin da kuma matsawa bututun da famfo daidai da kusoshi, goro da masu wankin bazara.
③ Ɗaga fam ɗin da ke ƙarƙashin ruwa kaɗan, cire matsi a saman ƙarshen famfon na ruwa, ɗaure kebul ɗin da ƙarfi ga bututun ruwa tare da tef ɗin filastik, sannan a daure ta ƙasa har sai an sanya matsi a bakin rijiyar.
④ Yi amfani da wannan hanyar don ɗaure duk bututun ruwa a cikin rijiyar.
⑤ Bayan an haɗa kebul na gubar da aka haɗa zuwa maɓallin sarrafawa, an haɗa shi da wutar lantarki na matakai uku.

(4) Abubuwan lura yayin shigarwa:
1. Idan an sami wani abin damuwa yayin aikin famfo, juya ko ja bututun ruwa don shawo kan matsewar. Idan har yanzu matakai daban-daban ba su yi aiki ba, don Allah kar a tilasta famfo ƙasa don guje wa lalacewa ga famfon lantarki da ke ƙarƙashin ruwa da rijiyar.
2. A lokacin shigarwa, ya kamata a sanya takalmin roba a gefen kowane bututu kuma a ɗaure shi daidai.
3. Idan aka saukar da famfon ruwa a cikin rijiyar, sai a sanya shi a tsakiyar bututun rijiyar don hana famfo yin gudu da bangon rijiyar na tsawon lokaci, wanda hakan zai sa fam ɗin ya yi rawar jiki, motar kuma ta share ta ƙone. .
4. Ƙayyade zurfin famfo na ruwa zuwa kasan rijiyar bisa ga yanayin yashi da yashi na rijiyar. Kada a binne famfo a cikin laka. Nisa daga famfon ruwa zuwa kasan rijiyar gabaɗaya bai wuce mita 3 ba (duba hoto na 2).
5. Zurfin shigar ruwa na famfo ruwa ya kamata ya zama ƙasa da mita 1-1.5 daga matakin ruwa mai ƙarfi zuwa kullin shigar ruwa (duba Hoto 2). In ba haka ba, famfo famfo na ruwa na iya lalacewa cikin sauƙi.
6. Tashin famfo na ruwa ba zai iya zama ƙasa da ƙasa ba. In ba haka ba, ana buƙatar shigar da bawul ɗin gate a kan bututun ruwa na rijiyar don sarrafa magudanar famfo a wurin da aka ƙididdige shi don hana yin lodin motar da ƙonewa saboda yawan kwararar ruwa.
7. Lokacin da famfo na ruwa ke gudana, fitar da ruwa ya kamata ya kasance mai ci gaba kuma har ma, halin yanzu ya kamata ya kasance mai ƙarfi (a karkashin yanayin aiki mai ƙima, gabaɗaya ba fiye da 10% na halin yanzu ba), kuma kada a yi rawar jiki ko amo. Idan akwai wata matsala, yakamata a dakatar da injin don gano dalilin da kuma kawar da shi.
8. Lokacin shigarwa, kula da saitin waya ta ƙasa (duba hoto 2). Lokacin da bututun ruwa ya kasance bututun ƙarfe, kai shi daga matsewar rijiyar; lokacin da bututun ruwa ya zama bututun filastik, kai shi daga alamar ƙasa na famfon lantarki.

 1.submersible pump installation is complete, re-check the insulation resistance and three-phase conduction from the switch, check the instrument and start the equipment connection error, if there is no problem, can start the trial, after the start of the instrument indicating readings whether more than the nameplate stipulated rated voltage and current, observe the pump noise and vibration phenomenon, everything is normal can be put into operation.

 2.pump operation for the first four hours, should be shut down quickly test the thermal insulation resistance of the motor, the value should not be less than 0.5 megaohm.

 3.pump shutdown, should be started after an interval of five minutes, to prevent the water column in the pipe has not completely reflux caused by excessive motor current and burnout.

 4.pump into normal operation, in order to prolong its service life, to check the supply voltage, working current and insulation resistance is normal, if found the following situation, should immediately shut down troubleshooting.

 1.in the rated condition, the current is more than20%.

 2.dynamic water level to the water inlet section, causing intermittent water.

 3.submersible pump severe vibration or noise.

 4.supply voltage is lower than 340 volts.

 5.fuse burned out a phase.

 6.water pipe damage.

 7.motor to the thermal insulation resistance is less than 0.5 megaohm. 5. The product is a pump unit with easy disassembly function, with simple steps of disassembly, so that users can easily maintain and clean. The disassembly steps include unraveling the cable rope, taking down the pipeline part and the line protection plate, unloosening the water discharge bolt, excluding all the water in the motor chamber, removing the filter and loosening the coupling fixing screw fixing the motor shaft, unscrewing the bolt connecting the water inlet section and the motor, separating the pump and the motor (note that the unit should be leveled when separating to prevent the bending of the pump shaft), the disassembly sequence of the pump is: water inlet section, impeller, shunt shell, impeller, and cleaning the valve body. When disassembling the impeller, use special tools to loosen the conical sleeve fixing the impeller. In the whole disassembly process, avoid bending the pump shaft and damaging various parts. The disassembly process of the motor is: put the motor on the platform, and remove the nuts, base, shaft head lock nut, thrust plate, key, and lower guide rail from the bottom of the motor in order. Bearing seat, tie rod bolt, and then take out the rotor (be careful not to damage the wiring harness) and finally remove the connecting section and the upper guide bearing seat. Before assembling the unit, the rust and dirt of each part should be cleaned, and the sealant should be coated on each mating surface and fastener, and then the assembly should be carried out in reverse order according to the disassembly (the movement of the motor shaft after assembly is about 1 mm). After the assembly is completed, the coupling should be flexibly rotated, and then the filter should be put on for machine test. This pump unit is not only convenient and easy to use, but also has detailed instructions, which provides users with convenient maintenance experience. 6. Submersible electric pump every operation for one year, or less than one year but the diving time has reached two years, should be put out of the well according to Article 5 for disassembly and maintenance, and replace the worn parts.

1, fitar da ruwa a cikin rami na motar (musamman a lokacin hunturu don hana motar daga daskarewa), kuma daure kebul ɗin da kyau.

2, adana a cikin daki na cikin gida ba tare da lalata abubuwa da gas ba, tare da zafin jiki ƙasa da 40 ° C.

3, dogon lokacin amfani ya kamata kula da tsatsa rigakafin submersible farashinsa.

01 Ruwa mai zurfi mai zurfi

02 Ruwa mai tsayi mai tsayi

03 ruwan tudu

04 Tower ruwa

05 Noma ban ruwa

06 ban ruwa na lambu

07 ruwan kogi  

08 ruwan gida