200QJR Zurfin Rijiya Mai Ruwa Mai Ruwa

Hot water motor using 50W400 high grade cold rolled silicon steel, stamping by high speed punch, make its stator iron loss is low, less heating advantages, the motor winding using high temperature, anti-aging hot water motor special winding water line, using 3CR13 stainless steel impeller shaft, high temperature sleeve and other high quality accessories, so that it can run at high temperature for a long time, and can be used with a frequency converter, so that it can automatically adjust according to the size of the water consumption.

This product is a three-phase AC 380V power supply (tolerance ± 5%), 50HZ frequency (tolerance ± 1%) pump, suitable for pumping water temperature not higher than 20 °C water. Specific requirements include: solid impurities content is not greater than 0.01%; PH value between 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The pump adopts closed or water sealed structure, before use must be filled with water, tighten the water and air exhaust bolts, otherwise not to use. The pump must be completely immersed in water, immersion depth shall not exceed 70m, and the distance from the bottom of the well shall not be less than 3m. The water flow in the well shall meet the requirements of the pump output and continuous operation, the pump output shall be controlled at 0.7-1.2 times the rated flow. The well shall be vertical, the pump can not be used horizontally or tilted, only vertical use. The pump must be equipped with cables and external overload protection device according to the requirements. It is strictly prohibited to test the pump without water and no load.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, tsananin bisa ga tanadi na famfo daga, kwarara kewayon amfani, don hana low kwarara ko high daga yin famfo karfi, da tura hali da sauran sassa na lalacewa, da mota obalodi kone.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Brief gabatarwar tsarin: famfo part aka yafi hada da famfo shaft, impeller, karkatar da harsashi, roba hali, duba bawul jiki (na zaɓi sassa) da sauran aka gyara. Bangaren motar ya ƙunshi tushe, fim mai daidaita matsa lamba, ɗaukar nauyi, farantin turawa, wurin zama mai jagorar ƙasa, stator, rotor, wurin zama mai jagora na sama, zoben yashi, sashin shigar ruwa, kebul da sauran abubuwan haɗin gwiwa.

Babban fasali na samfurin sun haɗa da:

 1, Motar ne mai jika mai cike da ruwa mai cike da ruwa mai cike da ruwa guda uku asynchronous motor, kogon motar yana cike da ruwa mai tsafta, ana amfani da shi don sanyaya motar da mai mai ɗaukar nauyi, ana amfani da fim ɗin daidaita matsi a ƙasan motar don daidaitawa. bambancin matsa lamba da fadadawa da matsa lamba na ruwa a cikin jiki wanda ya haifar da canjin yanayin zafi na motar.

 2, Don hana yashi a cikin rijiyar ruwa daga shiga cikin motar, babban ƙarshen motar motar yana sanye da hatimin mai guda biyu, kuma an sanya zoben yashi don samar da tsarin rigakafin yashi.

 3, Domin hana fam ɗin famfo daga tashi sama lokacin farawa, ana haɗa fam ɗin famfo da injin motar ta hanyar haɗin gwiwa, kuma an shigar da madaidaicin matsa lamba a ƙasan ɓangaren motar.

 4, The lubrication na mota da famfo hali ne ruwa lubrication.

 5, The motor stator winding da aka yi da high quality submersible motor winding waya, tare da high rufi yi.

 6, An tsara famfo ta kwamfuta CAD, tare da tsari mai sauƙi da kyakkyawan aikin fasaha.

(1)Shiri kafin shigarwa:
1. Bincika ko famfo mai nutsewa ya dace da yanayin amfani da iyaka da aka ƙayyade a cikin littafin.
2. Yin amfani da maɗaukaki mai nauyi tare da diamita daidai da matsakaicin matsakaicin diamita na waje na famfo, auna ko inneldimeter na rijiyar zai iya dacewa da famfo mai ruwa, kuma auna ko zurfin rijiyar ya dace da bukatun shigarwa.
3. A duba ko rijiyar tana da tsafta da kuma ko ruwan rijiyar turbude ne. Kada a taɓa amfani da famfon lantarki mai nutsewa don wanke laka na welor da ruwan yashi don gujewa lalacewa da wuri ga famfon lantarki mai nisa.
4. Bincika ko matsayin mannen shigarwa na welhead ya dace kuma ko zai iya jure ingancin duka naúrar.
5. Bincika idan kayan aikin famfo na submersible sun cika kuma an shigar dasu yadda ya kamata bisa ga zanen taron da ke cikin littafin
6. Cire dunƙule ruwa kuma cika ramin motar da ruwa mai tsabta mara lalacewa (bayanin kula. Tabbatar da cika shi), sannan ƙara matse ruwan. Bayan sa'o'i 12 na allurar ruwa, juriyar juriya na motar kada ta zama ƙasa da 150M Q lokacin da aka auna tare da tebur girgiza 500V.
7. Cable haɗin gwiwa, yanke hannun riga na 120mm na roba daga ƙarshen kebul ɗin da ke fita da kuma kebul ɗin da ya dace da wukar na'urar lantarki sa'an nan kuma ya girgiza tsawon wayoyi guda uku a cikin siffar taku, a cire wani cibiya na jan karfe 20mm, goge oxide. Layer a gefen wayar tagulla tare da wuka ko yashi, sannan a saka ƙarshen waya biyu da aka haɗa a cikin palirs.Bayan daure Layer tam tare da lallausan wayar tagulla, sayar da shi sosai da ƙarfi, da yashi kowane. burrs a saman. Sa'an nan kuma, don haɗin gwiwa guda uku, yi amfani da tef ɗin rufewa na polyvester don nannade su a cikin wani ɗan ƙaramin tsari don lafazin uku. Kunna ƙarshen Layer ɗin biyu tare da zaren nyion, sa'an nan kuma yi amfani da hanyar da aka ɗora tazara don nannade tef ɗin don yadudduka uku. Kunna fitar da waje tare da tef ɗin rufewa mai ƙarfi don yadudduka uku. A ƙarshe, ninka nau'i-nau'i uku tare kuma kunsa su akai-akai don yadudduka biyar tare da babban tef. Kowane Layer dole ne a daure sosai, kuma haɗin haɗin haɗin gwiwar dole ne su kasance masu ƙarfi kuma su kasance masu ƙarfi don hana ruwa shiga da lalata rufin, Bayan nannade, jiƙa a cikin ruwa a cikin dakin da zafin jiki na 20 'c na tsawon awanni 12, sannan a auna juriya na rufi tare da tebur mai girgiza. , wanda bai kamata ya zama ƙasa da 100M Ω ba

Jadawalin tsarin aikin wayoyi na USB wanda aka makala shine kamar haka:

8. Yi amfani da multimeter don bincika ko an haɗa wayoyi masu hawa uku kuma ko juriyar DC ta kusan daidaita.
9. Bincika ko ikon kewayawa da na'ura mai canzawa sun yi yawa, sa'an nan kuma haɗa maɓallin kariya daga overload ko kayan farawa. Dubi Table 2 don takamaiman samfura, sa'an nan kuma Zuba guga na ruwa a cikin famfo na ruwa daga tashar famfo na ruwa don sa mai da igiya na roba a cikin famfo, sa'an nan kuma sanya famfo na lantarki da ke karkashin ruwa a tsaye kuma a tsaye. Fara (ba fiye da dakika ɗaya ba) kuma duba ko jagoran tuƙi ya yi daidai da alamar tuƙi. Idan ba haka ba, musanya kowane haɗe-haɗe biyu na kebul na zamani uku. Sannan shigar da tacewa kuma shirya don gangara rijiyar. Idan aka yi amfani da shi a lokuta na musamman (kamar ramuka, ramuka, koguna, tafkuna, tafkuna, da sauransu), famfon lantarki dole ne ya zama ƙasa da dogaro.

(2) Kayan aiki da kayan aiki:
1. Ɗaya daga cikin sarƙoƙi na ɗagawa don fiye da ton biyu.
2. Tafiya mai tsayi a tsaye wanda bai gaza mita hudu ba.
3. Igiyoyin rataye guda biyu ( igiyoyin waya ) waɗanda zasu iya ɗaukar nauyin fiye da ton ɗaya (za su iya ɗaukar nauyin cikakken saitin famfo na ruwa).
4. Shigar da nau'i-nau'i biyu na manne (splints).
5. Wrenches, guduma, screwdrivers, lantarki kayan aiki da kayan aiki, da dai sauransu.

(3) Shigar da famfun lantarki:
1. Shigarwa ta hanyar yin gwajin lantarki mai saukarwa an nuna shi a cikin Hoto na 2. Ana nuna takamaiman girma a cikin Table 3 "Jerin shigarwa girma na famfo mai saukarwa".

2. Za a iya ɗaga famfunan wutar lantarki da ke ƙarƙashin ƙasa da kai ƙasa da mita 30 kai tsaye a cikin rijiyar ta hanyar amfani da tudu da igiyoyin waya ko wasu igiyoyin hemp waɗanda za su iya ɗaukar cikakken nauyin injin gabaɗaya, bututun ruwa, da ruwa a cikin bututu.

3. Pumps tare da shugaban sama da mita 30 suna amfani da bututun ƙarfe, kuma tsarin shigarwa shine kamar haka:
①A yi amfani da matsi don matse ƙarshen ɓangaren fanfo na ruwa (motar da famfon ɗin an haɗa su a wannan lokacin), ɗaga shi da sarƙar rataye, a hankali daure shi a cikin rijiyar har sai a daka matsi a kan rijiyar a cire. sarkar rataye.
② Yi amfani da wani nau'i na manne guda biyu don matsa bututu, ɗaga shi tare da sarƙar rataye 15 cm daga flange, kuma rage shi a hankali. Tsakanin flange na bututu da famfo flange Saka robar kushin a wurin da kuma matsawa bututun da famfo daidai da kusoshi, goro da masu wankin bazara.
③ Ɗaga fam ɗin da ke ƙarƙashin ruwa kaɗan, cire matsi a saman ƙarshen famfon na ruwa, ɗaure kebul ɗin da ƙarfi ga bututun ruwa tare da tef ɗin filastik, sannan a daure ta ƙasa har sai an sanya matsi a bakin rijiyar.
④ Yi amfani da wannan hanyar don ɗaure duk bututun ruwa a cikin rijiyar.
⑤ Bayan an haɗa kebul na gubar da aka haɗa zuwa maɓallin sarrafawa, an haɗa shi da wutar lantarki na matakai uku.

(4) Abubuwan lura yayin shigarwa:
1. Idan an sami wani abin damuwa yayin aikin famfo, juya ko ja bututun ruwa don shawo kan matsewar. Idan har yanzu matakai daban-daban ba su yi aiki ba, don Allah kar a tilasta famfo ƙasa don guje wa lalacewa ga famfon lantarki da ke ƙarƙashin ruwa da rijiyar.
2. A lokacin shigarwa, ya kamata a sanya takalmin roba a gefen kowane bututu kuma a ɗaure shi daidai.
3. Idan aka saukar da famfon ruwa a cikin rijiyar, sai a sanya shi a tsakiyar bututun rijiyar don hana famfo yin gudu da bangon rijiyar na tsawon lokaci, wanda hakan zai sa fam ɗin ya yi rawar jiki, motar kuma ta share ta ƙone. .
4. Ƙayyade zurfin famfo na ruwa zuwa kasan rijiyar bisa ga yanayin yashi da yashi na rijiyar. Kada a binne famfo a cikin laka. Nisa daga famfon ruwa zuwa kasan rijiyar gabaɗaya bai wuce mita 3 ba (duba hoto na 2).
5. Zurfin shigar ruwa na famfo ruwa ya kamata ya zama ƙasa da mita 1-1.5 daga matakin ruwa mai ƙarfi zuwa kullin shigar ruwa (duba Hoto 2). In ba haka ba, famfo famfo na ruwa na iya lalacewa cikin sauƙi.
6. Tashin famfo na ruwa ba zai iya zama ƙasa da ƙasa ba. In ba haka ba, ana buƙatar shigar da bawul ɗin gate a kan bututun ruwa na rijiyar don sarrafa magudanar famfo a wurin da aka ƙididdige shi don hana yin lodin motar da ƙonewa saboda yawan kwararar ruwa.
7. Lokacin da famfo na ruwa ke gudana, fitar da ruwa ya kamata ya kasance mai ci gaba kuma har ma, halin yanzu ya kamata ya kasance mai ƙarfi (a karkashin yanayin aiki mai ƙima, gabaɗaya ba fiye da 10% na halin yanzu ba), kuma kada a yi rawar jiki ko amo. Idan akwai wata matsala, yakamata a dakatar da injin don gano dalilin da kuma kawar da shi.
8. Lokacin shigarwa, kula da saitin waya ta ƙasa (duba hoto 2). Lokacin da bututun ruwa ya kasance bututun ƙarfe, kai shi daga matsewar rijiyar; lokacin da bututun ruwa ya zama bututun filastik, kai shi daga alamar ƙasa na famfon lantarki.

According to the product description, our submersible pump after installation needs careful inspection and testing to ensure its normal operation and prolong the service life. After installation, it is necessary to recheck the insulation resistance and three-phase continuity to ensure that the instrument and the start-up equipment are connected correctly. Before starting the test machine, observe whether the indication readings of the instruments are correct, check whether the rated voltage and current specified on the nameplate are exceeded, and observe whether there is noise or vibration in the pump. If everything is normal, it can be put into operation. After the pump runs for the first four hours, the motor thermal insulation resistance should be closed and quickly tested, and its value should not be less than 0.5 megaohms. After stopping the pump, it needs to be restarted at an interval of five minutes to prevent the water column in the pipeline from returning to cause the motor to burn out due to excessive current. After normal operation, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. Once abnormal conditions are found, such as the current exceeds 20% of the rated working conditions, the water level drops causing intermittent drainage, the submersible pump vibrates or makes loud noise, the supply voltage is lower than 340 volts, one phase in the fuse is burned out, the water pipe is damaged or the motor's thermal insulation resistance to the earth is less than 0.5 megaohms, the machine should be stopped immediately to eliminate the fault. When disassembling the unit, it is necessary to operate in accordance with the specified sequence to avoid damaging various components. Once a year or less than one year of use but has been immersed for two years, it must be disassembled and inspected in accordance with the provisions, and the worn parts must be replaced to ensure the normal operation and service life of the submersible electric pump.

 1, fitar da ruwa a cikin rami na motar (musamman a lokacin hunturu don hana motar daga daskarewa), kuma daure kebul ɗin da kyau.

 2, adana a cikin daki na cikin gida ba tare da lalata abubuwa da gas ba, tare da zafin jiki ƙasa da 40 ° C.

 3, dogon lokacin amfani ya kamata kula da tsatsa rigakafin submersible farashinsa.

01 Ruwa mai zurfi mai zurfi

02 Ruwa mai tsayi mai tsayi

03 ruwan tudu 

04 Tower ruwa

05 Noma ban ruwa

06 ban ruwa na lambu

07 ruwan kogi

08 ruwan gida