125QJP Peep Well Submersible Pum

QJP series fountain pump is a fountain pump with higher efficiency developed and researched by our factory. The pump motor core adopts high quality cold rolled silicon steel, which makes the pump have good magnetic conductivity and frequent start without heating.

The motor rotor ends use water as lubricant alloy copper sleeve instead of ball bearings, avoiding the problem of easy rust, rust and lack of oil wear and tear of the motor.

1, tuʻuina atu eletise: tolu-vaega AC 380V (faʻapalepale + / - 5%), 50HZ (faʻapalepale + / - 1%).

2, lelei vai:

(1) water temperature is not higher than 20 °C;

(2) faʻamaʻi eleelea faʻamaʻi (fuainumera tele) e le sili atu i le 0.01%;

(3) PH tau (pH) 6.5-8.5;

(4) e le sili atu i le 1.5mg/L mea e maua i le hydrogen sulfide;

(5) e le sili atu i le 400mg/L le mea o iai ion chloride.

3, o le afi tapuni poʻo le faʻatumu vai susu fausaga, aʻo leʻi faʻaaogaina le vaʻa afi afi e tatau ona tumu i vai mama, e puipuia ai le tumu sese, ona faʻamalosi lea o le tui vai, faʻamau faʻamalolo ea, a le o lea e le faʻatagaina e faʻaaoga.

4, e tatau ona goto uma i totonu o le vai, o le loloto o le maulu e le sili atu nai lo le 70m, o le pito i lalo ole pamu mai le pito i lalo ole vaieli e le itiiti ifo i le 3m.

5, e tatau ona mafai e le vai lelei ona faʻafeiloaʻi le gaosiga o le pamu vai ma faʻaauau pea le faʻagaioiga, e tatau ona pulea le gaosiga o le suavai i le 0.7 - 1.2 taimi o le tafe fua.

6, e tatau ona saʻo le vaieli, e le mafai ona faʻaaogaina pe lafoai le pamu faʻafefe, naʻo le faʻaogaina i luga.

7, o le pamu submersible e tatau ona faʻafetaui ma le uaea e tusa ai ma manaʻoga, ma le masini puipuia le mamafa i fafo.

8, o le pamu e matua faʻasaina e aunoa ma se vai e leai se uta masini suʻega

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, e tusa ai ma aiaiga o le pamu siitia, tafe le tele o le faʻaaogaina, e puipuia ai le maualalo o le tafe poʻo le maualuga o le maualuga o le pamuina o le malosi, o le faʻaosoina ma isi vaega o le ofuina, o le afi tele na susunuina.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Fa'atomuaga pu'upu'u o le fausaga: vaega pamu e masani lava ona aofia ai le pamu pamu, impeller, atigi fa'afefete, pa'u pa'u, siaki valve tino (vaega faitalia) ma isi vaega. O vaega ole afi e tele lava ina aofia ai le faavae, ata tifaga faʻatonutonuina, faʻapipiʻi faʻamalosi, ipu faʻapipiʻi, nofoa faʻataʻitaʻiga pito i lalo, stator, rotor, nofoa faʻataʻitaʻi pito i luga, mama oneone, vaega ole vai, uaea ma isi vaega.

O uiga autu o le oloa e aofia ai:

 1, O le afi o se afi faʻafefe susu e tolu-vaega asynchronous afi e tumu i le vai, o le afi afi e tumu i vai mama, faʻaaogaina e faʻamalo ai le afi ma faʻafefe le faʻamomoli, o le faʻatonuga faʻatonutonu ata i le pito i lalo o le afi e faʻaaogaina e fetuunai ai. o le faʻalauteleina ma le faʻaitiitia o le eseesega o le mamafa o le vai i totonu o le tino e mafua mai i le suiga o le vevela o le afi.

 2, Ina ia puipuia le oneone i totonu o le vaieli mai le ulufale atu i le afi, o le pito i luga o le afi afi ua faʻapipiʻiina i faʻamaufaʻailoga suauʻu lua, ma faʻapipiʻi se mama oneone e fausia ai se fausaga puipuia o le oneone.

 3, Ina ia puipuia le pamu pamu mai le alu i luga pe a amata, o le pamu pamu ma le afi afi e fesoʻotaʻi e se soʻotaga, ma faʻapipiʻi le pito i luga o le faʻamau i le pito i lalo o le afi.

 4, O le lubrication o le afi ma le pamu o le vai lubrication.

 5, O le afi stator winding e faia i le tulaga maualuga submersible afi viliina uaea, ma le faatinoga insulation maualuga.

 6, O le pamu ua mamanuina e le komepiuta CAD, faʻatasi ai ma le faʻaogaina faigofie ma le lelei o faʻatinoga faʻapitoa.

(1) Sauniuniga aʻo leʻi faʻapipiʻiina:
1. Siaki pe fetaui le pamu fa'asusu i le fa'aogaina ma le lautele o lo'o fa'ailoa mai ile tusi lesona.
2. Fa'aaogaina o se obiect mamafa ma le lautele e tutusa ma le maualuga pito i fafo o le pamu fa'asusu, fua pe mafai e le inneldiameter o le vaieli ona ofi le pamu fa'asusu, ma fua pe o le loloto o le vai e fetaui ma mana'oga fa'apipi'i.
3. Siaki pe mama le vaieli ma pe o le vaieli e pala. 'Aua ne'i fa'aogaina se pamu eletise e fa'ato'ilaloina e fufulu ai le palapala ma le oneone o le pa'u welor e 'alofia ai le vave fa'aleagaina o le pamu eletise fa'alalo.
4. Siaki pe talafeagai le tulaga o le faʻapipiʻi welhead faʻapipiʻi ma pe mafai ona tatalia le tulaga o le iunite atoa
5. Siaki pe ua mae'a ma fa'apipi'i lelei vaega o pamu fa'asusu e tusa ai ma le fa'ata'otoga o lo'o i totonu o le tusi lesona.
6. Tatala le fa'avili vai ma fa'atumu le oga o le afi i vai mama, e le pala (matau. ia mautinoa e fa'atutu i luga), ona fa'amau lea o le fa'asuavai. A maeʻa le 12 itula o le tui vai, e le tatau ona itiiti ifo i le 150M Q le teteʻe o le afi ile 500V pe a fua ile laulau lulu 500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

O le fa'apipi'i fa'apipi'i fa'asologa o fa'agasologa o uaea e fa'apea:

8. Fa'aaoga se multimeter e siaki ai pe o feso'ota'i laina e tolu-vaega ma pe fa'atatau i le paleni DC.
9. Siaki pe sili atu le mamafa o le eletise ma le transformer, ona faʻafesoʻotaʻi lea o le ki o le puipuiga o le mamafa poʻo le amataina o meafaigaluega. Va'ai le Laulau 2 mo fa'ata'ita'iga fa'apitoa, ona sasaa lea o se pakete vai i totonu o le pamu vai mai le pamu vai e fa'alu'u ai pa'u pa'u i totonu o le pamu, ona tu'u sa'o lea o le pamu eletise fa'ato'ilalo ma tumau. ma siaki pe o ogatasi le fa'atonuga ma le fa'ailoga fa'atonu. Afai e leai, fesuiai soʻo se lua fesoʻotaʻiga o le tolu-vaega uaea. Ona faʻapipiʻi lea o le faamama ma sauni e alu i lalo o le vaieli. Afai e faʻaaogaina i taimi faʻapitoa (e pei o alavai, alavai, vaitafe, vaituloto, vaituloto, ma isi), o le pamu eletise e tatau ona faʻalagolago i le eleele.

(2) Fa'apipi'i meafaigaluega ma meafaigaluega:
1. Tasi le pea o filifili si'i mo le sili atu i le lua tone.
2. O se tripod ma le maualuga tuusaʻo e le itiiti ifo i le fa mita.
3. E lua maea tautau (uaea uaea) e mafai ona tauave le mamafa e sili atu ma le tasi tone (e mafai ona tauave le mamafa o se seti atoa o pamu vai).
4. Fa'apipi'i ni paipa se lua (splints).
5. Tu'u, samala, sikuli, meafaigaluega eletise ma meafaigaluega, ma isi.

(3) Fa'apipi'i pamu eletise:
1. O le faʻapipiʻiina o le faʻapipiʻiina o le pamu eletise o loʻo faʻaalia i le Ata 2. O faʻamaufaʻailoga faʻapipiʻi faʻapitoa o loʻo faʻaalia i le Laulau 3 "Lisi o Fua Faʻapipiʻi o le Pump Eletise Submersible".

2. O pamu eletise e mafai ona faʻafefeteina ma le ulu e itiiti ifo i le 30 mita e mafai ona sisi saʻo i totonu o le vaieli e faʻaaoga ai faʻagaau ma maea uaea poʻo isi maea hemp e mafai ona tauaveina le mamafa atoa o le masini, paipa vai, ma vai i totonu o paipa.

3. O pamu ma le ulu e sili atu i le 30 mita e faʻaaogaina paipa uʻamea, ma o le faʻasologa faʻapipiʻi e faʻapea:
①Fa'aoga le pipii e pipii ai le pito pito i luga ole vaega o le pamu vai (o le afi ma le pamu vai o loʻo fesoʻotaʻi i le taimi lea), sii i luga i se filifili tautau, ma nonoa lemu i totonu o le vaieli seia tuʻu le faʻamau i luga o le ulu vaieli ma aveese le filifili tautau.
② Fa'aaoga se isi pea paipa e pipii ai se paipa, sii i luga i se filifili tautau e 15 cm le mamao mai le apa, ma tuutuu i lalo lemu. I le va o lau paipa ma le pamu pamu Fa'amau le pa'u ma fa'amau le paipa ma pamu fa'atasi i fa'amau, nati ma fufulu vaipuna.
③ Si'i teisi le pamu vai, aveese le pipii i le pito pito i luga o le pamu vai, nonoa le uaea i le paipa vai i se pa'u palasitika, ma nonoa malie i lalo seia tu'u le pipii i le ulu vaieli.
④ Fa'aaoga le auala lava e tasi e nonoa uma ai paipa vai i totonu o le vaieli.
⑤A maeʻa ona fesoʻotaʻi le uaea taʻitaʻia i le ki faʻatonutonu, e faʻafesoʻotaʻi i le sapalai eletise tolu-vaega.

(4) Mea e matauina i le taimi o le faʻapipiʻiina:
1. Afai e maua se fa'alavelave fa'afuase'i i le taimi o le pamu, liliu pe toso le paipa vai e fa'ato'ilalo ai le mea fa'amau. Afai e le aoga lava faiga eseese, faamolemole aua le faamalosia le pamu i lalo e aloese ai mai le faaleagaina o le pamu eletise ma le vaieli.
2. I le taimi o le faʻapipiʻiina, e tatau ona tuʻu se paʻu paʻu i le flange o paipa taʻitasi ma faʻapipiʻi tutusa.
3. A tuu i lalo le pamu vai i totonu o le vaieli, e tatau ona tuʻu i le ogatotonu o le paipa vaieli e puipuia ai le pamu mai le faʻasaga i le puipui o le vaieli mo se taimi umi, ma mafua ai ona tete le pamu ma salu ma mu le afi. .
4. Fuafua le loloto o le pamu vai i le pito i lalo o le vaieli e tusa ai ma tulaga o le tafe o le oneone ma le palapala o le vaieli. Aua le tanumia le pamu i le palapala. O le mamao mai le pamu vai i le pito i lalo o le vaieli e masani lava e le itiiti ifo i le 3 mita (silasila i le Ata 2).
5. O le loloto o le vai o le pamu vai e tatau ona le itiiti ifo i le 1-1.5 mita mai le maualuga o le vai i le node o le vai (silasila i le Ata 2). A leai, e mafai ona faigofie ona faʻaleagaina le paʻu vai.
6. O le si'itia o le pamu vai e le mafai ona maualalo tele. A leai, e tatau ona fa'apipi'i se alavai faitoto'a i luga o le paipa vai e fa'atonutonu ai le tafe o le pamu i le nofoaga fa'atatau e puipuia ai le afi mai le mamafa ma mu ona o le tele o tafega.
7. A oʻo ina tamoʻe le pamu vai, e tatau ona faʻaauau pea le gaosiga o le vai ma e oʻo lava, o le taimi nei e tatau ona mautu (i lalo o tulaga faigaluega faʻatulagaina, e masani lava e le sili atu i le 10% o le taimi nei faʻamauina), ma e le tatau ona i ai se vibration poʻo le pisa. Afai ei ai se faaletonu, e tatau ona taofi le masini e suʻe le mafuaʻaga ma faʻaumatia.
8. A faʻapipiʻi, faʻalogo lelei i le faʻatulagaina o le uaea faʻavae afi (silasila i le Ata 2). Afai o le paipa vai o se paipa u'amea, ta'ita'i mai le fa'amau o le vaieli; pe a avea le paipa vai o se paipa palasitika, taʻitaʻia mai le faʻailoga o le pamu eletise.

• 1. A maeʻa ona faʻapipiʻi le pamu submersible, siaki le faʻaogaina o le insulation ma le tolu-vaega faʻatautaia mai le ki, siaki pe sese le meafaigaluega ma le fesoʻotaʻiga o mea amata, pe a leai se faʻafitauli, e mafai ona amata le masini faʻataʻitaʻiga, ma mataʻituina pe sili atu le fua faʻatatau o le meafaifaʻaili i le voltage faʻamaonia ma le taimi nei o loʻo faʻamaonia i luga o le nameplate pe a maeʻa le amataga, ma mataʻituina pe o le pamu o loʻo i ai le pisapisao ma le vibration, ma faʻaogaina pe a masani mea uma.
• 2. A maeʻa le faʻaogaina muamua o le pamu mo le fa itula, e tatau ona tapuni le afi e faʻataʻitaʻi vave le faʻaogaina o le vevela, ma o lona tau e le tatau ona itiiti ifo i le 0.5 megaohm.
• 3. A maeʻa ona tapunia le pamu, e tatau ona amata pe a uma le lima minute e puipuia ai le koluma vai i totonu o le paipa mai le toe faʻaleleia atoatoa ma mafua ai le tele o le afi afi ma le susunuina.
• 4. A maeʻa ona tuʻuina le pamu i le gaioiga masani, ina ia faʻaumiina lona ola tautua, e tatau ona siaki pe o le voltage tuʻuina atu, galue i le taimi nei ma le faʻaogaina o le insulation e masani lava. Afai e maua tulaga nei, e tatau ona tapuni vave le pamu e foia faafitauli.
•  
• - I le tulaga faʻatulagaina, o le taimi nei e sili atu i le 20%.
• - O le maualuga o le vai e pa'ū i le vaega o le vai, ma mafua ai le vai vavao.
• - O le pamu fa'afefeteina e tele le vibration po'o le pisa.
• - E la'ititi ifo ile 340 volts le eletise.
• - Ua mu se fuse.
• - Ua leaga le paipa vai.
• - O le fa'alumaina fa'amama a le afi e maualalo ifo nai lo le 0.5 megaohm.
•  
• Unit disassembly:
• (1)Untie the cable tie, remove the pipeline part, and remove the wire plate.
• (2)screw down the water bolt, put the water in the motor chamber.
• (3)remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• (4)screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• (5)the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• (6)the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• (7)unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.
•  

 1, tuu i fafo le vai i totonu o le afi (aemaise lava i le taumalulu e puipuia ai le afi mai le malulu), ma nonoa lelei le uaea.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 3, faʻaaogaina umi e tatau ona gauai atu i le puipuia o le ele o pamu submersible.

01 Vaivai loloto

02 Suavai maualuga

03 vai mai mauga 

04 vai olo

05 Fa'asusu fa'ato'aga

06 fa'asusuina o togalaau

07 vai inu vai

08 vai aiga