175QJP Peep Well Submersible Pum

QJP series fountain pump is a special pump for fountain developed by our factory.The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, good magnetic conductivity, and frequent start will not fever.Both ends of the motor rotor use water as lubricant alloy copper sleeve.Stainless steel sleeve instead of ball bearings, to avoid the problem of easy rust ball bearings and lack of oil wear and tear the motor.The most suitable for music fountain use, all models can be used.

This product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply system. Applicable water quality conditions include water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L. The motor is a closed or water-filled wet structure. Before use, it must be filled with clean water to prevent false filling, and then tighten the water injection and exhaust bolts, otherwise it is not allowed to use. The submersible pump must be completely immersed in water, and the penetration depth shall not exceed 70m. The distance between the submersible pump base and the bottom of the well shall not be less than 3m. The well flow shall be able to meet the water output and continuous operation of the submersible pump. The water output of the submersible pump shall be controlled at 0.7-1.2 times of the rated flow. The well shall be vertical, and the submersible pump can not be used horizontally or upside down, but only vertically. The submersible pump shall be equipped with cables and external overload protection devices as required. The pump is strictly prohibited from no-load test without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, e tusa ai ma aiaiga o le pamu siitia, tafe le tele o le faʻaaogaina, e puipuia ai le maualalo o le tafe poʻo le maualuga o le maualuga o le pamuina o le malosi, o le faʻaosoina ma isi vaega o le ofuina, o le afi tele na susunuina.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The main features of the product include: the motor is a water immersed wet three-phase asynchronous motor, the motor cavity is full of water, used to cool the motor and lubricate the bearing; the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of temperature; in order to prevent the sand particles in the well water from entering the motor, two oil seals are installed on the upper end of the motor shaft extension, and a sand control structure is formed by installing the sand ring; in order to prevent the pump shaft from jumping at startup, the pump shaft is connected with the motor shaft through a coupling, and the thrust bearing is installed under the motor; the lubrication of the motor and the pump bearing is water lubrication; the stator winding of the motor is made of high quality submersible motor winding, with high insulation performance; the pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Sauniuniga aʻo leʻi faʻapipiʻiina:
1. Siaki pe fetaui le pamu fa'asusu i le fa'aogaina ma le lautele o lo'o fa'ailoa mai ile tusi lesona.
2. Fa'aaogaina o se obiect mamafa ma le lautele e tutusa ma le maualuga pito i fafo o le pamu fa'asusu, fua pe mafai e le inneldiameter o le vaieli ona ofi le pamu fa'asusu, ma fua pe o le loloto o le vai e fetaui ma mana'oga fa'apipi'i.
3. Siaki pe mama le vaieli ma pe o le vaieli e pala. 'Aua ne'i fa'aogaina se pamu eletise e fa'ato'ilaloina e fufulu ai le palapala ma le oneone o le pa'u welor e 'alofia ai le vave fa'aleagaina o le pamu eletise fa'alalo.
4. Siaki pe talafeagai le tulaga o le faʻapipiʻi welhead faʻapipiʻi ma pe mafai ona tatalia le tulaga o le iunite atoa
5. Siaki pe ua mae'a ma fa'apipi'i lelei vaega o pamu fa'asusu e tusa ai ma le fa'ata'otoga o lo'o i totonu o le tusi lesona.
6. Tatala le fa'avili vai ma fa'atumu le oga o le afi i vai mama, e le pala (matau. ia mautinoa e fa'atutu i luga), ona fa'amau lea o le fa'asuavai. A maeʻa le 12 itula o le tui vai, e le tatau ona itiiti ifo i le 150M Q le teteʻe o le afi ile 500V pe a fua ile laulau lulu 500V.
7. Uaea so'oga, tipi ese le lima pa'u 120mm mai le tasi pito o le uaea fafo ma le uaea tutusa ma le naifi eletise ona tautevateva le umi o uaea autu e tolu i se foliga la'a, pa'u ese le 20mm apamemea autu, solo le oxide. faʻapipiʻi i fafo o le uaea apamemea ma se naifi poʻo se ie oneone, ma faʻapipiʻi pito uaea fesoʻotaʻi e lua i palirs.A uma ona nonoa le faʻamau i le uaea apamemea lelei, solder maeʻaeʻa ma mausali, ma oneone soʻo se mea. burrs i luga o le fogaeleele. Ona, mo sooga e tolu, faʻaaoga le polyvester insulation tape e afifi ai i se faiga faʻaputu faʻapipiʻi mo le tolu vai. Afifi pito e lua o le apa afifi i le filo nyion, ona fa'aoga lea o se auala fa'aputu fa'aputu e afifi ai le lipine mo fa'avae e tolu. Afifi le pito i fafo i le mea fa'apipi'i fa'amaualuga maualuga mo vaega e tolu. Mulimuli ane, gaugau fa'atasi ia manoa e tolu ma fa'afia ona afifiina mo fa'apalima fa'atasi ma le lipine fa'amalo maualuga. E tatau ona fusifusia vaega taʻitasi, ma e tatau ona fufusi ma faʻamauina sooga faʻapipiʻi e puipuia ai le vai mai le ulu ma faʻaleagaina le faʻamalo, A maeʻa ona afifi, faʻasusu i le vai i le vevela o le 20 'c mo le 12 itula, ma fua le faʻamaʻi faʻafefe ma se laulau lulu. , lea e le tatau ona itiiti ifo i le 100M Ω

O le fa'apipi'i fa'apipi'i fa'asologa o fa'agasologa o uaea e fa'apea:

8. Fa'aaoga se multimeter e siaki ai pe o feso'ota'i laina e tolu-vaega ma pe fa'atatau i le paleni DC.
9. Siaki pe sili atu le mamafa o le eletise ma le transformer, ona faʻafesoʻotaʻi lea o le ki o le puipuiga o le mamafa poʻo le amataina o meafaigaluega. Va'ai le Laulau 2 mo fa'ata'ita'iga fa'apitoa, ona sasaa lea o se pakete vai i totonu o le pamu vai mai le pamu vai e fa'alu'u ai pa'u pa'u i totonu o le pamu, ona tu'u sa'o lea o le pamu eletise fa'ato'ilalo ma tumau. ma siaki pe o ogatasi le fa'atonuga ma le fa'ailoga fa'atonu. Afai e leai, fesuiai soʻo se lua fesoʻotaʻiga o le tolu-vaega uaea. Ona faʻapipiʻi lea o le faamama ma sauni e alu i lalo o le vaieli. Afai e faʻaaogaina i taimi faʻapitoa (e pei o alavai, alavai, vaitafe, vaituloto, vaituloto, ma isi), o le pamu eletise e tatau ona faʻalagolago i le eleele.

(2) Fa'apipi'i meafaigaluega ma meafaigaluega:
1. Tasi le pea o filifili si'i mo le sili atu i le lua tone.
2. O se tripod ma le maualuga tuusaʻo e le itiiti ifo i le fa mita.
3. E lua maea tautau (uaea uaea) e mafai ona tauave le mamafa e sili atu ma le tasi tone (e mafai ona tauave le mamafa o se seti atoa o pamu vai).
4. Fa'apipi'i ni paipa se lua (splints).
5. Tu'u, samala, sikuli, meafaigaluega eletise ma meafaigaluega, ma isi.

(3) Fa'apipi'i pamu eletise:
1. O le faʻapipiʻiina o le faʻapipiʻiina o le pamu eletise o loʻo faʻaalia i le Ata 2. O faʻamaufaʻailoga faʻapipiʻi faʻapitoa o loʻo faʻaalia i le Laulau 3 "Lisi o Fua Faʻapipiʻi o le Pump Eletise Submersible".

2. O pamu eletise e mafai ona faʻafefeteina ma le ulu e itiiti ifo i le 30 mita e mafai ona sisi saʻo i totonu o le vaieli e faʻaaoga ai faʻagaau ma maea uaea poʻo isi maea hemp e mafai ona tauaveina le mamafa atoa o le masini, paipa vai, ma vai i totonu o paipa.

3. O pamu ma le ulu e sili atu i le 30 mita e faʻaaogaina paipa uʻamea, ma o le faʻasologa faʻapipiʻi e faʻapea:
①Fa'aoga le pipii e pipii ai le pito pito i luga ole vaega o le pamu vai (o le afi ma le pamu vai o loʻo fesoʻotaʻi i le taimi lea), sii i luga i se filifili tautau, ma nonoa lemu i totonu o le vaieli seia tuʻu le faʻamau i luga o le ulu vaieli ma aveese le filifili tautau.
② Fa'aaoga se isi pea paipa e pipii ai se paipa, sii i luga i se filifili tautau e 15 cm le mamao mai le apa, ma tuutuu i lalo lemu. I le va o lau paipa ma le pamu pamu Fa'amau le pa'u ma fa'amau le paipa ma pamu fa'atasi i fa'amau, nati ma fufulu vaipuna.
③ Si'i teisi le pamu vai, aveese le pipii i le pito pito i luga o le pamu vai, nonoa le uaea i le paipa vai i se pa'u palasitika, ma nonoa malie i lalo seia tu'u le pipii i le ulu vaieli.
④ Fa'aaoga le auala lava e tasi e nonoa uma ai paipa vai i totonu o le vaieli.
⑤A maeʻa ona fesoʻotaʻi le uaea taʻitaʻia i le ki faʻatonutonu, e faʻafesoʻotaʻi i le sapalai eletise tolu-vaega.

(4) Mea e matauina i le taimi o le faʻapipiʻiina:
1. Afai e maua se fa'alavelave fa'afuase'i i le taimi o le pamu, liliu pe toso le paipa vai e fa'ato'ilalo ai le mea fa'amau. Afai e le aoga lava faiga eseese, faamolemole aua le faamalosia le pamu i lalo e aloese ai mai le faaleagaina o le pamu eletise ma le vaieli.
2. I le taimi o le faʻapipiʻiina, e tatau ona tuʻu se paʻu paʻu i le flange o paipa taʻitasi ma faʻapipiʻi tutusa.
3. A tuu i lalo le pamu vai i totonu o le vaieli, e tatau ona tuʻu i le ogatotonu o le paipa vaieli e puipuia ai le pamu mai le faʻasaga i le puipui o le vaieli mo se taimi umi, ma mafua ai ona tete le pamu ma salu ma mu le afi. .
4. Fuafua le loloto o le pamu vai i le pito i lalo o le vaieli e tusa ai ma tulaga o le tafe o le oneone ma le palapala o le vaieli. Aua le tanumia le pamu i le palapala. O le mamao mai le pamu vai i le pito i lalo o le vaieli e masani lava e le itiiti ifo i le 3 mita (silasila i le Ata 2).
5. O le loloto o le vai o le pamu vai e tatau ona le itiiti ifo i le 1-1.5 mita mai le maualuga o le vai i le node o le vai (silasila i le Ata 2). A leai, e mafai ona faigofie ona faʻaleagaina le paʻu vai.
6. O le si'itia o le pamu vai e le mafai ona maualalo tele. A leai, e tatau ona fa'apipi'i se alavai faitoto'a i luga o le paipa vai e fa'atonutonu ai le tafe o le pamu i le nofoaga fa'atatau e puipuia ai le afi mai le mamafa ma mu ona o le tele o tafega.
7. A oʻo ina tamoʻe le pamu vai, e tatau ona faʻaauau pea le gaosiga o le vai ma e oʻo lava, o le taimi nei e tatau ona mautu (i lalo o tulaga faigaluega faʻatulagaina, e masani lava e le sili atu i le 10% o le taimi nei faʻamauina), ma e le tatau ona i ai se vibration poʻo le pisa. Afai ei ai se faaletonu, e tatau ona taofi le masini e suʻe le mafuaʻaga ma faʻaumatia.
8. A faʻapipiʻi, faʻalogo lelei i le faʻatulagaina o le uaea faʻavae afi (silasila i le Ata 2). Afai o le paipa vai o se paipa u'amea, ta'ita'i mai le fa'amau o le vaieli; pe a avea le paipa vai o se paipa palasitika, taʻitaʻia mai le faʻailoga o le pamu eletise.

• 1.After installing the submersible pump, recheck the insulation resistance and the three-phase continuity at the switch, and check whether there are errors in the connection of the instrument and the starting equipment.If there are no problems, you can start to test the machine. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump emits any noise or vibration. If everything is normal, it can be put into operation.
• 2. After the pump runs for the first four hours, the thermal insulation resistance of the motor should be closed and tested quickly.Its value should not be less than 0.5 megaohm.After the pump stops, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing and burning the motor due to excessive current.
• 3. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to troubleshoot.
•  
• 1 I le tulaga galue fa'atulagaina, o le taimi nei e sili atu i le 20%.
• 2 O le maualuga o le vai e pa'ū i le vaega o le vai, ma mafua ai le vai vavave.
• 3 O le pamu fa'afefeteina e tele le tetete po'o le pisa.
• 4 E maualalo ifo i le 340 volts le voltage sapalai.
• 5 Ua mu se fuse.
• 6 Ua leaga le paipa vai.
• 7 O le fa'alumaina o le afi i le tulaga geothermal e maualalo ifo nai lo le 0.5 megaohm.
•  
• Unit disassembly:
• 1.untie cable rope, remove the pipeline part, remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the inlet junction with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) inlet junction, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising of the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the reverse order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product adopts advanced design and provides advanced storage suggestions to ensure long-term use effect.First of all, in winter, it is necessary to exhaust all the water to prevent freezing. In addition, the wire rolls should be placed well and tied up.Secondly, when storing, the environment without corrosive action and gas should be selected and the temperature should be kept below 40 °C. Finally, when not used for a long time, attention should be paid to prevent rust of submersible pump.These storage requirements will ensure that the product can maintain its performance status and prolong its service life for a long time.

01 Vaivai loloto

02 Suavai maualuga

03 vai mai mauga 

04 vai olo

05 Fa'asusu fa'ato'aga

06 fa'asusuina o togalaau

07 vai inu vai

08 vai aiga