175QJB Va'alele Loloto Pamu

The product adopts special water-resistant wire for motor winding, with excellent characteristics such as high frequency shock resistance, pulse peak voltage shock resistance and high temperature aging resistance. The frequency conversion winding design ensures the motor to operate smoothly between 1Hz and 50Hz for a long time, making the frequency conversion deep well pump more energy saving and longer service life.

We are honored to introduce our products, this product provides three-phase AC 380V power supply (tolerance of ± 5%), 50HZ voltage (tolerance of ± 1%). At the same time, our products require strict water quality requirements: water temperature is not higher than 20 °C; solid impurities content (mass ratio) is not greater than 0.01%; PH value (pH) is 6.5-8.5; hydrogen sulfide content is not greater than 1.5mg/L; chloride ion content is not greater than 400mg/L. The motor adopts closed or water-filled wet structure, which must be filled with clean water before use to prevent empty. Tighten the water charging and deflating bolts before use, otherwise, it is not allowed to use. The submersible pump must be completely immersed in water to work, the immersion depth shall not exceed 70 meters, and the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The well water flow shall meet the output and continuous operation requirements of the submersible pump, and the output of the submersible pump shall be controlled at 0.7-1.2 times of the rated flow. The well must be vertical, and the submersible pump can not be used horizontally or inverted, but only vertically. The submersible pump must be equipped with cables according to requirements, and is equipped with external overload protection devices. It is strictly prohibited to conduct no-load tests on the pump without water. Our products guarantee to provide you with high quality and stable performance, while meeting your needs to ensure safe and reliable.

This well submersible pump is a pump suitable for clean water. Digging new wells and pumping sediment and turbid water are strictly prohibited. The voltage grade of the well pump is 380V/50HZ. Submersible motors with other voltage grades need to be customized. Underground cables must use waterproof cables and must be equipped with starting equipment, such as distribution boxes, etc. The starting equipment should have common comprehensive motor protection functions, such as overload short circuit protection, phase loss protection, undervoltage protection, grounding protection and idling protection, etc. In abnormal cases, the protection device should be tripped in time. During installation and use, the pump must be reliably grounded. It is prohibited to push and pull the switch when hands and feet are wet. The power supply must be cut off before installation and maintenance of the pump. The place where the pump is used must be set up with obvious "anti-electric shock" marks. Before going down the well or installation, the motor must be injected with distilled water or non-corrosive clear cold water in the inner cavity, and the intake/drain bolts must be tightened. When testing the pump on the ground, water must be injected into the pump chamber to lubricate the rubber bearings. The instant start time should not exceed one second to check whether the direction is correct. The same as the steering instructions. Pay attention to safety when the pump is upright to prevent tilting and injury. Strictly in accordance with the provisions of the pump lift and flow range, to prevent the pump flow at low lift or in high lift pull too large, resulting in extreme wear of thrust bearings and other components, the motor due to overload and burn. After put into the well, the measurement of the motor and the ground insulation resistance value, not less than 100M. After the start, regular observation of voltage and current, and check the motor winding insulation is in line with the requirements of the provisions. If the temperature of the storage site is below the freezing point, the water in the pump chamber should be drained to prevent the water in the motor chamber from freezing and damaging the motor due to low temperature.

Fa'atomuaga pu'upu'u o le fausaga: vaega pamu e masani lava ona aofia ai le pamu pamu, impeller, atigi fa'afefete, pa'u pa'u, siaki valve tino (vaega faitalia) ma isi vaega. O vaega ole afi e tele lava ina aofia ai le faavae, ata tifaga faʻatonutonuina, faʻapipiʻi faʻamalosi, ipu faʻapipiʻi, nofoa faʻataʻitaʻiga pito i lalo, stator, rotor, nofoa faʻataʻitaʻi pito i luga, mama oneone, vaega ole vai, uaea ma isi vaega.

O uiga autu o le oloa e aofia ai:

1.The motor is a water-filled wet submersible three-phase asynchronous motor, the motor cavity is full of clean water, used to cool the motor and lubricate the bearing, the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the water inside the body caused by the change of the temperature rise of the motor.

2.In order to prevent the sand in the well water from entering the motor, the upper end of the motor shaft is equipped with two oil seals, and a sand ring is installed to form a sand prevention structure.

3.In order to prevent the pump shaft from running up when starting, the pump shaft and the motor shaft are connected by a coupling, and an upper thrust bearing is installed at the lower part of the motor.

4.The lubrication of the motor and the pump bearing is water lubrication.

5.The motor stator winding is made of high quality submersible motor winding wire, with high insulation performance.

6.The pump is designed by computer CAD, with simple structure and good technical performance.

(1) Sauniuniga aʻo leʻi faʻapipiʻiina:
1. Siaki pe fetaui le pamu fa'asusu i le fa'aogaina ma le lautele o lo'o fa'ailoa mai ile tusi lesona.
2. Fa'aaogaina o se obiect mamafa ma le lautele e tutusa ma le maualuga pito i fafo o le pamu fa'asusu, fua pe mafai e le inneldiameter o le vaieli ona ofi le pamu fa'asusu, ma fua pe o le loloto o le vai e fetaui ma mana'oga fa'apipi'i.
3. Siaki pe mama le vaieli ma pe o le vaieli e pala. 'Aua ne'i fa'aogaina se pamu eletise e fa'ato'ilaloina e fufulu ai le palapala ma le oneone o le pa'u welor e 'alofia ai le vave fa'aleagaina o le pamu eletise fa'alalo.
4. Siaki pe talafeagai le tulaga o le faʻapipiʻi welhead faʻapipiʻi ma pe mafai ona tatalia le tulaga o le iunite atoa
5. Siaki pe ua mae'a ma fa'apipi'i lelei vaega o pamu fa'asusu e tusa ai ma le fa'ata'otoga o lo'o i totonu o le tusi lesona.
6. Tatala le fa'avili vai ma fa'atumu le oga o le afi i vai mama, e le pala (matau. ia mautinoa e fa'atutu i luga), ona fa'amau lea o le fa'asuavai. A maeʻa le 12 itula o le tui vai, e le tatau ona itiiti ifo i le 150M Q le teteʻe o le afi ile 500V pe a fua ile laulau lulu 500V.
7. Uaea so'oga, tipi ese le lima pa'u 120mm mai le tasi pito o le uaea fafo ma le uaea tutusa ma le naifi eletise ona tautevateva le umi o uaea autu e tolu i se foliga la'a, pa'u ese le 20mm apamemea autu, solo le oxide. faʻapipiʻi i fafo o le uaea apamemea ma se naifi poʻo se ie oneone, ma faʻapipiʻi pito uaea fesoʻotaʻi e lua i palirs.A uma ona nonoa le faʻamau i le uaea apamemea lelei, solder maeʻaeʻa ma mausali, ma oneone soʻo se mea. burrs i luga o le fogaeleele. Ona, mo sooga e tolu, faʻaaoga le polyvester insulation tape e afifi ai i se faiga faʻaputu faʻapipiʻi mo le tolu vai. Afifi pito e lua o le apa afifi i le filo nyion, ona fa'aoga lea o se auala fa'aputu fa'aputu e afifi ai le lipine mo fa'avae e tolu. Afifi le pito i fafo i le mea fa'apipi'i fa'amaualuga maualuga mo vaega e tolu. Mulimuli ane, gaugau fa'atasi ia manoa e tolu ma fa'afia ona afifiina mo fa'apalima fa'atasi ma le lipine fa'amalo maualuga. E tatau ona fusifusia vaega taʻitasi, ma e tatau ona fufusi ma faʻamauina sooga faʻapipiʻi e puipuia ai le vai mai le ulu ma faʻaleagaina le faʻamalo, A maeʻa ona afifi, faʻasusu i le vai i le vevela o le 20 'c mo le 12 itula, ma fua le faʻamaʻi faʻafefe ma se laulau lulu. , lea e le tatau ona itiiti ifo i le 100M Ω

O le fa'apipi'i fa'apipi'i fa'asologa o fa'agasologa o uaea e fa'apea:

8. Fa'aaoga se multimeter e siaki ai pe o feso'ota'i laina e tolu-vaega ma pe fa'atatau i le paleni DC.
9. Siaki pe sili atu le mamafa o le eletise ma le transformer, ona faʻafesoʻotaʻi lea o le ki o le puipuiga o le mamafa poʻo le amataina o meafaigaluega. Va'ai le Laulau 2 mo fa'ata'ita'iga fa'apitoa, ona sasaa lea o se pakete vai i totonu o le pamu vai mai le pamu vai e fa'alu'u ai pa'u pa'u i totonu o le pamu, ona tu'u sa'o lea o le pamu eletise fa'ato'ilalo ma tumau. ma siaki pe o ogatasi le fa'atonuga ma le fa'ailoga fa'atonu. Afai e leai, fesuiai soʻo se lua fesoʻotaʻiga o le tolu-vaega uaea. Ona faʻapipiʻi lea o le faamama ma sauni e alu i lalo o le vaieli. Afai e faʻaaogaina i taimi faʻapitoa (e pei o alavai, alavai, vaitafe, vaituloto, vaituloto, ma isi), o le pamu eletise e tatau ona faʻalagolago i le eleele.

(2) Fa'apipi'i meafaigaluega ma meafaigaluega:
1. Tasi le pea o filifili si'i mo le sili atu i le lua tone.
2. O se tripod ma le maualuga tuusaʻo e le itiiti ifo i le fa mita.
3. E lua maea tautau (uaea uaea) e mafai ona tauave le mamafa e sili atu ma le tasi tone (e mafai ona tauave le mamafa o se seti atoa o pamu vai).
4. Fa'apipi'i ni paipa se lua (splints).
5. Tu'u, samala, sikuli, meafaigaluega eletise ma meafaigaluega, ma isi.

(3) Fa'apipi'i pamu eletise:
1. O le faʻapipiʻiina o le faʻapipiʻiina o le pamu eletise o loʻo faʻaalia i le Ata 2. O faʻamaufaʻailoga faʻapipiʻi faʻapitoa o loʻo faʻaalia i le Laulau 3 "Lisi o Fua Faʻapipiʻi o le Pump Eletise Submersible".

2. O pamu eletise e mafai ona faʻafefeteina ma le ulu e itiiti ifo i le 30 mita e mafai ona sisi saʻo i totonu o le vaieli e faʻaaoga ai faʻagaau ma maea uaea poʻo isi maea hemp e mafai ona tauaveina le mamafa atoa o le masini, paipa vai, ma vai i totonu o paipa.

3. O pamu ma le ulu e sili atu i le 30 mita e faʻaaogaina paipa uʻamea, ma o le faʻasologa faʻapipiʻi e faʻapea:
①Fa'aoga le pipii e pipii ai le pito pito i luga ole vaega o le pamu vai (o le afi ma le pamu vai o loʻo fesoʻotaʻi i le taimi lea), sii i luga i se filifili tautau, ma nonoa lemu i totonu o le vaieli seia tuʻu le faʻamau i luga o le ulu vaieli ma aveese le filifili tautau.
② Fa'aaoga se isi pea paipa e pipii ai se paipa, sii i luga i se filifili tautau e 15 cm le mamao mai le apa, ma tuutuu i lalo lemu. I le va o lau paipa ma le pamu pamu Fa'amau le pa'u ma fa'amau le paipa ma pamu fa'atasi i fa'amau, nati ma fufulu vaipuna.
③ Si'i teisi le pamu vai, aveese le pipii i le pito pito i luga o le pamu vai, nonoa le uaea i le paipa vai i se pa'u palasitika, ma nonoa malie i lalo seia tu'u le pipii i le ulu vaieli.
④ Fa'aaoga le auala lava e tasi e nonoa uma ai paipa vai i totonu o le vaieli.
⑤A maeʻa ona fesoʻotaʻi le uaea taʻitaʻia i le ki faʻatonutonu, e faʻafesoʻotaʻi i le sapalai eletise tolu-vaega.

(4) Mea e matauina i le taimi o le faʻapipiʻiina:
1. Afai e maua se fa'alavelave fa'afuase'i i le taimi o le pamu, liliu pe toso le paipa vai e fa'ato'ilalo ai le mea fa'amau. Afai e le aoga lava faiga eseese, faamolemole aua le faamalosia le pamu i lalo e aloese ai mai le faaleagaina o le pamu eletise ma le vaieli.
2. I le taimi o le faʻapipiʻiina, e tatau ona tuʻu se paʻu paʻu i le flange o paipa taʻitasi ma faʻapipiʻi tutusa.
3. A tuu i lalo le pamu vai i totonu o le vaieli, e tatau ona tuʻu i le ogatotonu o le paipa vaieli e puipuia ai le pamu mai le faʻasaga i le puipui o le vaieli mo se taimi umi, ma mafua ai ona tete le pamu ma salu ma mu le afi. .
4. Fuafua le loloto o le pamu vai i le pito i lalo o le vaieli e tusa ai ma tulaga o le tafe o le oneone ma le palapala o le vaieli. Aua le tanumia le pamu i le palapala. O le mamao mai le pamu vai i le pito i lalo o le vaieli e masani lava e le itiiti ifo i le 3 mita (silasila i le Ata 2).
5. O le loloto o le vai o le pamu vai e tatau ona le itiiti ifo i le 1-1.5 mita mai le maualuga o le vai i le node o le vai (silasila i le Ata 2). A leai, e mafai ona faigofie ona faʻaleagaina le paʻu vai.
6. O le si'itia o le pamu vai e le mafai ona maualalo tele. A leai, e tatau ona fa'apipi'i se alavai faitoto'a i luga o le paipa vai e fa'atonutonu ai le tafe o le pamu i le nofoaga fa'atatau e puipuia ai le afi mai le mamafa ma mu ona o le tele o tafega.
7. A oʻo ina tamoʻe le pamu vai, e tatau ona faʻaauau pea le gaosiga o le vai ma e oʻo lava, o le taimi nei e tatau ona mautu (i lalo o tulaga faigaluega faʻatulagaina, e masani lava e le sili atu i le 10% o le taimi nei faʻamauina), ma e le tatau ona i ai se vibration poʻo le pisa. Afai ei ai se faaletonu, e tatau ona taofi le masini e suʻe le mafuaʻaga ma faʻaumatia.
8. A faʻapipiʻi, faʻalogo lelei i le faʻatulagaina o le uaea faʻavae afi (silasila i le Ata 2). Afai o le paipa vai o se paipa u'amea, ta'ita'i mai le fa'amau o le vaieli; pe a avea le paipa vai o se paipa palasitika, taʻitaʻia mai le faʻailoga o le pamu eletise.

• 1.After installing the submersible pump, recheck the insulation resistance and three-phase continuity switch, check whether there is any error in the connection between the instrument and the starting equipment.If there is no problem, you can start to test the machine. After starting, observe whether the indication reading of each instrument is correct.If the rated voltage and current specified on the nameplate are exceeded, please observe whether the pump has noise or vibration.If everything is normal, it can be put into operation. After the pump runs for the first time for four hours, the motor thermal insulation resistance should be closed and tested quickly. Its value should not be less than 0.5 megaohm. After the pump stops, it should be restarted after five minutes to prevent the water column in the pipeline from completely reversing, which will cause the motor to burn out due to excessive current.
•  
• 2.After the pump is put into normal operation, in order to prolong its service life, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. If the following conditions are found, the machine should be stopped immediately to troubleshoot.
• 1.Under the rated working condition, the current exceeds 20%.
• 2.The dynamic water level drops to the water inlet section, resulting in intermittent water.
• 3.The submersible pump has severe vibration or noise.
• 4.The supply voltage is lower than 340 volts.
• 5.A fuse is burned out.
• 6.The water pipeline is damaged.
• 7.The motor's insulation resistance to the geothermal state is lower than 0.5 megaohm.
•  
• 3.Unit disassembly:
• - Tatala le nonoa uaea, aveese le vaega o paipa, ma aveese le ipu uaea.
• - screw down the water bolt, put out the water in the motor chamber.
• - aveese le faamama, tatala le sikulima mau i luga o le sooga e faʻaleleia ai le afi afi.
•  
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 1, tuu i fafo le vai i totonu o le afi (aemaise lava i le taumalulu e puipuia ai le afi mai le malulu), ma nonoa lelei le uaea.

 2, teu i totonu o se potu i totonu e aunoa ma ni mea pala ma kasa, ma le vevela i lalo ole 40 °C.

 3, faʻaaogaina umi e tatau ona gauai atu i le puipuia o le ele o pamu submersible.