200QJR Jin Daradara Submersible fifa

Hot water motor using 50W400 high grade cold rolled silicon steel, stamping by high speed punch, make its stator iron loss is low, less heating advantages, the motor winding using high temperature, anti-aging hot water motor special winding water line, using 3CR13 stainless steel impeller shaft, high temperature sleeve and other high quality accessories, so that it can run at high temperature for a long time, and can be used with a frequency converter, so that it can automatically adjust according to the size of the water consumption.

This product is a three-phase AC 380V power supply (tolerance ± 5%), 50HZ frequency (tolerance ± 1%) pump, suitable for pumping water temperature not higher than 20 °C water. Specific requirements include: solid impurities content is not greater than 0.01%; PH value between 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The pump adopts closed or water sealed structure, before use must be filled with water, tighten the water and air exhaust bolts, otherwise not to use. The pump must be completely immersed in water, immersion depth shall not exceed 70m, and the distance from the bottom of the well shall not be less than 3m. The water flow in the well shall meet the requirements of the pump output and continuous operation, the pump output shall be controlled at 0.7-1.2 times the rated flow. The well shall be vertical, the pump can not be used horizontally or tilted, only vertical use. The pump must be equipped with cables and external overload protection device according to the requirements. It is strictly prohibited to test the pump without water and no load.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, ni ibamu si awọn ipese ti fifa fifa soke, iwọn lilo ti sisan, lati ṣe idiwọ sisan kekere tabi agbara fifa soke, gbigbe gbigbe ati awọn ẹya miiran ti yiya, apọju motor sun.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Finifini ifihan ti be: fifa apakan wa ni o kun kq fifa ọpa, impeller, diversion ikarahun, roba ti nso, ṣayẹwo àtọwọdá ara (iyan awọn ẹya ara) ati awọn miiran irinše. Apakan mọto jẹ ipilẹ akọkọ ti ipilẹ, fiimu ti n ṣatunṣe titẹ, gbigbe gbigbe, awo titari, ijoko itọsona isalẹ, stator, rotor, ijoko gbigbe itọsọna oke, oruka iyanrin, apakan agbawọle omi, okun ati awọn paati miiran.

Awọn ẹya akọkọ ti ọja naa pẹlu:

 1, Awọn motor ti wa ni a omi-kún omi-kún tutu submersible mẹta-alakoso asynchronous motor, awọn motor iho ti kun ti o mọ omi, lo lati dara awọn motor ati lubricate awọn ti nso, awọn titẹ regulating fiimu ni isalẹ ti awọn motor ti wa ni lo lati ṣatunṣe. awọn imugboroosi ati ihamọ titẹ iyato ti omi inu awọn ara ṣẹlẹ nipasẹ awọn iyipada ti awọn iwọn otutu jinde ti awọn motor.

 2, Lati le ṣe idiwọ iyanrin ti o wa ninu omi kanga lati wọ inu ọkọ ayọkẹlẹ, opin oke ti ọpa ọkọ ayọkẹlẹ ti wa ni ipese pẹlu awọn edidi epo meji, ati pe a ti fi oruka iyanrin kan lati ṣe ilana idena iyanrin.

 3, Lati le ṣe idiwọ ọpa fifa soke lati ṣiṣẹ soke nigbati o bẹrẹ, ọpa fifa ati ọpa ọkọ ayọkẹlẹ ti wa ni asopọ nipasẹ iṣọpọ, ati pe a ti fi ọpa ti o ga julọ ni apa isalẹ ti motor.

 4, Awọn lubrication ti motor ati fifa fifa jẹ lubrication omi.

 5, Awọn motor stator yikaka ti wa ni ṣe ti ga didara submersible motor yikaka okun waya, pẹlu ga idabobo išẹ.

 6, A ṣe apẹrẹ fifa soke nipasẹ kọmputa CAD, pẹlu ọna ti o rọrun ati iṣẹ-ṣiṣe imọ-ẹrọ to dara.

(1) Igbaradi ṣaaju fifi sori:
1. Ṣayẹwo boya fifa omi inu omi ba pade awọn ipo lilo ati iwọn ti a pato ninu itọnisọna.
2. Lilo obiect ti o wuwo pẹlu iwọn ila opin ti o dọgba si iwọn ila opin ti ita ti o pọju ti fifa fifa, wiwọn boya inneldiameter ti wellbore le ni ibamu si fifa omi ti o wa ni isalẹ, ki o si wiwọn boya ijinle kanga ni ibamu pẹlu awọn ibeere fifi sori ẹrọ.
3. Ṣayẹwo boya ibi kanga jẹ mimọ ati boya omi kanga jẹ turbid. Maṣe lo fifa ina submersible lati fọ ẹrẹ fifa welor ati omi iyanrin lati yago fun ibajẹ ti tọjọ si fifa ina submersible.
4. Ṣayẹwo boya awọn ipo ti awọn welhead fifi sori dimole jẹ dara ati boya o le withstand awọn qualty ti gbogbo kuro
5. Ṣayẹwo boya awọn paati fifa submersible ti pari ati fi sori ẹrọ daradara ni ibamu si apẹrẹ apejọ ti o wa ninu iwe afọwọkọ Yọ iboju àlẹmọ naa ki o si yi asopọ pọ lati rii boya o n yi ni irọrun
6. Unscrew omi dabaru ati ki o fillthe motor iho pẹlu mọ, ti kii ipata omi (akọsilẹ. jẹ daju lati Fil o soke), ki o si Mu awọn waterscrew. Lẹhin awọn wakati 12 ti abẹrẹ omi, idabobo idabobo ti motor ko yẹ ki o kere ju 150M Q nigbati wọn wọn pẹlu tabili gbigbọn 500V.
7. Isopo okun, ge apo rọba 120mm kan lati opin kan ti okun ti njade ati okun ti o baamu pẹlu ọbẹ eletiriki lẹhinna ta gigun ti awọn okun onirin mẹta ni apẹrẹ ti o ni ipele, yọ mojuto 20mm Ejò kuro, yọ oxide. Layer lori theside ti awọn Ejò waya pẹlu kan ọbẹ tabi iyanrin asọ, ki o si fi awọn meji ti sopọ waya pari ni palirs.After tying awọn Layer ni wiwọ pẹlu itanran Ejò waya, solder o daradara ati ki o ìdúróṣinṣin, ati iyanrin ti eyikeyi. burrs lori dada. Lẹhinna, fun awọn isẹpo mẹta, lo teepu idabobo polyvester lati fi ipari si wọn ni ọna tolera ologbele fun awọn lafa mẹta. Pa awọn opin meji ti Layer wiwu ni wiwọ pẹlu okun nyion, ati lẹhinna lo ọna tolera ologbele lati fi ipari si teepu fun awọn fẹlẹfẹlẹ mẹta. Fi ipari si outellayer pẹlu teepu idabobo giga-titẹ fun awọn ipele mẹta. Nikẹhin, ṣe agbo awọn okun mẹta papo ki o si fi ipari si wọn leralera fun awọn marunlayers pẹlu teepu titẹ-giga. Layer kọọkan gbọdọ wa ni wiwọ ni wiwọ, ati awọn isẹpo interlayer gbọdọ jẹ ṣinṣin ati fimm lati yago fun omi lati wọ inu ati ba idabobo naa jẹ, Lẹhin ti murasilẹ, fi omi sinu omi ni iwọn otutu ti 20 'c fun wakati 12, ki o si wiwọn resistance idabobo pẹlu tabili gbigbọn. , eyiti ko yẹ ki o kere ju 100M Ω

Aworan ilana onirin okun ti a so mọ jẹ bi atẹle:

8. Lo multimeter kan lati ṣayẹwo boya awọn onirin mẹta-alakoso ti wa ni ti sopọ ati boya awọn DC resistance jẹ to iwontunwonsi.
9. Ṣayẹwo boya awọn Circuit ati transformer agbara ti wa ni apọju, ati ki o si so apọju Idaabobo yipada tabi ti o bere ẹrọ. Wo Tabili 2 fun awọn awoṣe kan pato, ati lẹhinna Tú garawa omi kan sinu fifa omi lati inu iṣan omi lati lubricate awọn bearings roba ninu fifa soke, ati lẹhinna gbe fifa ina mọnamọna submersible ni titọ ati iduroṣinṣin.Bẹrẹ (ko si ju iṣẹju kan lọ) ati ki o ṣayẹwo boya itọsọna idari ni ibamu pẹlu ami idari. Ti kii ba ṣe bẹ, paarọ eyikeyi awọn asopọ meji ti okun oni-mẹta. Lẹhinna fi àlẹmọ sori ẹrọ ki o mura lati lọ si isalẹ kanga naa. Ti a ba lo ni awọn iṣẹlẹ pataki (gẹgẹbi awọn koto, awọn koto, awọn odo, awọn adagun omi, awọn adagun omi, ati bẹbẹ lọ), fifa ina mọnamọna gbọdọ wa ni ilẹ ni igbẹkẹle.

(2) Awọn ohun elo fifi sori ẹrọ ati awọn irinṣẹ:
1. Ọkan bata ti awọn ẹwọn gbigbe fun diẹ ẹ sii ju awọn toonu meji lọ.
2. A mẹta pẹlu kan inaro iga ti ko kere ju mẹrin mita.
3. Awọn okun adiye meji (awọn okun waya) ti o le jẹ iwuwo diẹ ẹ sii ju ọkan lọ (le jẹ iwuwo ti pipe pipe ti awọn fifa omi).
4. Fi sori ẹrọ meji orisii clamps (splints).
5. Wrenches, òòlù, screwdrivers, itanna irinṣẹ ati ohun elo, ati be be lo.

(3) Fifi sori ẹrọ fifa ẹrọ itanna:
1. Aworan fifi sori ẹrọ ti fifa ina mọnamọna submersible ti wa ni afihan ni Nọmba 2. Awọn iwọn fifi sori ẹrọ pato ni a fihan ni Table 3 "Akojọ ti Awọn Iwọn fifi sori ẹrọ ti Imudanu Imọlẹ Imọlẹ".

2. Awọn ifasoke ina mọnamọna ti o wa ni isalẹ pẹlu ori ti o kere ju 30 mita ni a le gbe soke taara sinu kanga nipa lilo awọn okun ati awọn okun waya tabi awọn okun hemp miiran ti o le ni kikun iwuwo ti gbogbo ẹrọ, awọn ọpa omi, ati omi ninu awọn paipu.

3. Awọn ifasoke pẹlu ori ti o ju 30 mita lo awọn paipu irin, ati ilana fifi sori ẹrọ jẹ bi atẹle:
① Lo dimole kan lati di opin oke ti apakan fifa omi (moto ati fifa omi ti wa ni asopọ ni akoko yii), gbe e pẹlu ẹwọn ikele, ki o si sorara di e sinu kanga naa titi ti o fi fi dimole si ori kanga ki o si yọkuro ikele pq.
② Lo awọn clamps meji miiran lati di paipu kan, gbe e pẹlu ẹwọn ikele 15 cm kuro ni flange, ki o si lọ silẹ laiyara. Laarin pipe flange ati fifa flangeFi awọn roba pad ni ibi ati Mu paipu ati fifa boṣeyẹ pẹlu boluti, eso ati orisun omi washers.
③ Gbe fifa omi ti o wa ni isalẹ diẹ diẹ, yọ idimu ti o wa ni opin oke ti fifa omi, di okun naa ṣinṣin si paipu omi pẹlu teepu ike kan, ki o si so o lọra titi di igba ti a fi dimu si ibi kanga.
④ Lo ọna kanna lati di gbogbo awọn paipu omi sinu kanga.
⑤ Lẹhin ti okun-jade ti a ti sopọ si iyipada iṣakoso, o ti sopọ si ipese agbara mẹta-alakoso.

(4) Awọn nkan lati ṣe akiyesi lakoko fifi sori ẹrọ:
1. Ti o ba ti a jamming lasan ti wa ni ri nigba ti fifa ilana, tan tabi fa omi paipu lati bori awọn jamming ojuami. Ti ọpọlọpọ awọn igbese ko ba ṣiṣẹ, jọwọ maṣe fi agbara mu fifa soke lati yago fun ibajẹ si fifa ina submersible ati kanga.
2. Lakoko fifi sori ẹrọ, paadi rọba yẹ ki o gbe ni flange ti paipu kọọkan ati ki o ni wiwọ paapaa.
3. Nigbati fifa omi ba ti wa ni isalẹ sinu kanga, o yẹ ki o gbe si arin paipu kanga naa lati ṣe idiwọ fifa soke lati ṣiṣẹ lodi si odi kanga fun igba pipẹ, ti o mu ki fifa soke lati gbọn ati pe ọkọ ayọkẹlẹ lati gba ati sisun. .
4. Ṣe ipinnu ijinle ti fifa omi si isalẹ ti kanga gẹgẹbi iyanrin ti nṣan ati awọn ipo silt ti kanga. Ma ṣe sin fifa soke sinu ẹrẹ. Ijinna lati fifa omi si isalẹ ti kanga ni gbogbogbo ko kere ju awọn mita 3 (wo Nọmba 2).
5. Ijinle titẹsi omi ti fifa omi yẹ ki o jẹ ko kere ju awọn mita 1-1.5 lati ipele omi ti o ni agbara si oju omi ti nwọle (wo Nọmba 2). Bibẹẹkọ, awọn bearings fifa omi le ni irọrun bajẹ.
6. Gbigbe ti fifa omi ko le jẹ kekere ju. Bibẹẹkọ, àtọwọdá ẹnu-ọna nilo lati fi sori ẹrọ lori opo gigun ti omi kanga lati ṣakoso ṣiṣan fifa ni aaye ṣiṣan ti o ni iwọn lati ṣe idiwọ mọto lati ni apọju ati sisun nitori awọn iwọn sisan nla.
7. Nigbati fifa omi ba n ṣiṣẹ, ṣiṣan omi yẹ ki o wa ni ilọsiwaju ati paapaa, lọwọlọwọ yẹ ki o wa ni iduroṣinṣin (labẹ awọn ipo iṣẹ ti a ṣe ayẹwo, ni gbogbo igba ko ju 10% ti iṣiro lọwọlọwọ), ati pe ko yẹ ki o jẹ gbigbọn tabi ariwo. Ti aiṣedeede eyikeyi ba wa, ẹrọ naa yẹ ki o da duro lati wa idi ti o fa ati imukuro rẹ.
8. Nigbati fifi sori, san ifojusi si awọn eto ti awọn motor grounding waya (wo Figure 2). Nigbati paipu omi jẹ paipu irin, darí rẹ lati dimole kanga; nigbati paipu omi jẹ paipu ike kan, darí rẹ lati aami ilẹ ti fifa ina.

According to the product description, our submersible pump after installation needs careful inspection and testing to ensure its normal operation and prolong the service life. After installation, it is necessary to recheck the insulation resistance and three-phase continuity to ensure that the instrument and the start-up equipment are connected correctly. Before starting the test machine, observe whether the indication readings of the instruments are correct, check whether the rated voltage and current specified on the nameplate are exceeded, and observe whether there is noise or vibration in the pump. If everything is normal, it can be put into operation. After the pump runs for the first four hours, the motor thermal insulation resistance should be closed and quickly tested, and its value should not be less than 0.5 megaohms. After stopping the pump, it needs to be restarted at an interval of five minutes to prevent the water column in the pipeline from returning to cause the motor to burn out due to excessive current. After normal operation, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. Once abnormal conditions are found, such as the current exceeds 20% of the rated working conditions, the water level drops causing intermittent drainage, the submersible pump vibrates or makes loud noise, the supply voltage is lower than 340 volts, one phase in the fuse is burned out, the water pipe is damaged or the motor's thermal insulation resistance to the earth is less than 0.5 megaohms, the machine should be stopped immediately to eliminate the fault. When disassembling the unit, it is necessary to operate in accordance with the specified sequence to avoid damaging various components. Once a year or less than one year of use but has been immersed for two years, it must be disassembled and inspected in accordance with the provisions, and the worn parts must be replaced to ensure the normal operation and service life of the submersible electric pump.

 1, gbe omi jade ninu iho moto (paapaa ni igba otutu lati ṣe idiwọ mọto lati didi), ki o di okun naa daradara.

 2, tọju sinu yara inu ile laisi awọn nkan ti o bajẹ ati awọn gaasi, pẹlu iwọn otutu ti o wa labẹ 40 °C.

 3, gun-igba lilo yẹ ki o san ifojusi si ipata idena ti submersible bẹtiroli.

01 Gbigbe omi kanga ti o jinlẹ

02 Giga-jinde omi ipese

03 oke omi ipese 

04 omi ẹṣọ

05 Ogbin irigeson

06 irigeson ọgba

07 odo omi gbigbemi

08 omi inu ile