Ologbele-Alagbara, Irin Pipin Series Jin Well fifa

Awọn lilo ti omi immersed submersible motor, rotor wear-sooro alloy sleeve ati alloy thrust disiki design.More ti o tọ ju (epo immersed winding, rotor bearing motor), diẹ sii ayika friendly.No epo jijo lẹhin ikuna ti fifa soke, ko si idoti ti daradara omi, ailewu lilo.The impeller Ẹgbẹ lilo ga agbara egboogi-iyanrin wọ-sooro PC composite polima ohun elo, titun onisẹpo mẹta eefun ti oniru, lilefoofo impeller, seramiki egboogi-iyanrin be wọ resistance, ni kikun gbe, ti o tobi sisan.Omi-kún. motor le besomi ijinle 300 mita.

This product is a three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%) power supply system, designed for strict water quality requirements. The product is suitable for water temperature not higher than 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) between 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L environment. This product is equipped with a closed or water-filled wet structure motor, before use must be submersible motor inner cavity filled with clean water to prevent false full, and then tighten the water and air bolts, otherwise not to use. The submersible pump must be completely immersed in water to work, penetration depth shall not exceed 70 meters, the distance from the bottom of the pump to the bottom of the well shall not be less than 3 meters. In addition, the well water flow should meet the continuous operation requirements of the submersible pump, the water output of the submersible pump should be controlled at 0.7-1.2 times the rated flow. When used, the well must be vertical, and the submersible pump can not be used horizontally or dumped, only vertical installation. To ensure safety, the submersible pump must match the cable according to the requirements and be equipped with external overload protection device, and it is strictly prohibited to conduct no-load test on the pump without water. This product is an ideal choice for providing high quality water source, and can be widely used in various industrial and civil water processing fields.

 This kind of well submersible pump is a clean water pump. It is strictly prohibited to dig new wells and extract sediments and turbid water. The voltage grade of the well pump is 380/50HZ. The submersible motor with other voltage grades needs to be customized. Underground cables must be waterproof cables and must be equipped with starting equipment, such as distribution box, etc. The starting equipment should have common comprehensive motor protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and idling protection, etc., to prevent timely tripping when abnormal conditions occur. The pump must be reliably grounded during installation and use, and it is strictly prohibited to push and pull the switch when the hands and feet are wet. The power supply must be cut off before installation and maintenance of the pump. The place where the pump is used must be set up with obvious "anti-electric shock" marks. Before going down the well or installation, the motor must be filled with distilled water or non-corrosive clean cold water in the internal chamber, and the drain bolt must be fastened. When testing the pump on the ground, water must be injected into the pump chamber to lubricate the rubber bearings. The instantaneous start time shall not exceed one second to check whether the direction is correct, and the direction is the same as the direction indicator. When the pump is erected, pay attention to safety to prevent injury from tilting. Strictly in accordance with the provisions of the pump lift and flow range of use, to avoid the pump in the low flow when the large flow or in the high lift appears in the large pull, resulting in extreme wear of thrust bearings and other components, the motor overload and burn. After the pump into the well, the insulation resistance between the motor and the ground should be measured, not less than 100MΩ. After the start, regular observation of voltage and current, and check whether the motor winding insulation meets the requirements of the provisions. If the location temperature of the pump storage is below the freezing point, the water in the motor cavity should be drained, so as not to damage the motor in winter low temperature freezing.

1. 1.Submersible fifa fifi sori ẹrọ ti pari, tun-ṣayẹwo idabobo idabobo ati itọnisọna mẹta-mẹta lati iyipada, ṣayẹwo ohun elo naa ki o bẹrẹ aṣiṣe asopọ ẹrọ, ti ko ba si iṣoro, le bẹrẹ idanwo naa, lẹhin ibẹrẹ ti ohun elo ti n tọka si awọn kika boya diẹ sii ju foliteji ti a fiwewe orukọ ati lọwọlọwọ, ṣe akiyesi ariwo fifa ati lasan gbigbọn, ohun gbogbo jẹ deede ni a le fi si iṣẹ.
2. 2.Iṣẹ akọkọ ti fifa soke fun awọn wakati mẹrin, o yẹ ki o wa ni pipa ni kiakia ṣe idanwo idabobo igbona ti motor, iye ko yẹ ki o kere ju 0.5 megaohm.
3. 3.After awọn fifa soke tiipa, yẹ ki o wa bere lẹhin ti ẹya aarin ti iṣẹju marun, lati se awọn omi iwe ninu paipu ni o ni ko patapata reflux ṣẹlẹ nipasẹ nmu motor lọwọlọwọ ati burnout.
4. 4.After awọn fifa soke sinu deede isẹ ti, ni ibere lati pẹ awọn oniwe-iṣẹ aye, lati ṣayẹwo awọn foliteji ipese, ṣiṣẹ lọwọlọwọ ati idabobo resistance ni deede, ti o ba ri awọn wọnyi ipo, yẹ ki o lẹsẹkẹsẹ pa laasigbotitusita.
5.  

 1 ni ipo ti o ni iwọn, lọwọlọwọ jẹ diẹ sii ju 20%.

 2 ipele omi ti o ni agbara si apakan iwọle omi, nfa omi lainidii.

 3 submersible fifa nla gbigbọn tabi ariwo.

 4 foliteji ipese jẹ kekere ju 340 volts.

 5 fiusi iná jade a alakoso.

 6 omi paipu bibajẹ.

 7 mọto si resistance idabobo igbona kere ju megaohm 0.5.

5. 5.Unit dissembly:

 1 yọ okun tether kuro, yọ apakan opo gigun ti epo kuro, yọ awo okun waya kuro.

 2 dabaru boluti omi, fi omi sinu iyẹwu motor.

 3 yọ àlẹmọ kuro, tú dabaru ti o wa titi lori isopọpọ lati ṣatunṣe ọpa ọkọ.

 4 dabaru boluti ti o so apakan omi inu omi pẹlu mọto, ki o si ya fifa soke kuro ninu ọkọ (san akiyesi si aga timutimu nigbati o yapa, lati ṣe idiwọ atunse ti ọpa fifa)

 5 awọn disassembly ọkọọkan ti awọn fifa ni: (wo nọmba 1) omi agbawọle apakan, impeller, diversion ikarahun, impeller ...... ṣayẹwo àtọwọdá ara, nigbati o ba yọ awọn impeller, lo pataki irinṣẹ lati loosen awọn conical apo ti awọn ti o wa titi impeller akọkọ, ki o si yago fun atunse ati sọgbẹni awọn ọpa fifa ninu awọn ilana ti disassembly.

 6 ilana disassembly ti awọn motor ni: (wo nọmba 1) gbe awọn motor lori Syeed, ki o si yọ awọn eso, mimọ, ọpa ori tilekun nut, titari awo, bọtini, isalẹ guide ti nso ijoko ati ki o ė ori boluti lati isalẹ ti. awọn motor ni Tan, ati ki o si ya jade awọn ẹrọ iyipo (san ifojusi ko si ba awọn waya package) ati nipari yọ awọn asopọ apakan ati oke guide ti nso ijoko.

 7 kuro ijọ: ṣaaju ki o to ijọ, awọn ipata ati dọti ti awọn ẹya yẹ ki o wa ni ti mọtoto, ati awọn ibarasun dada ati fasteners ti a bo pẹlu sealant, ati ki o si jọ ni idakeji ibere ti disassembly (awọn motor ọpa rare si oke ati isalẹ lẹhin ijọ fun nipa ọkan. milimita), lẹhin apejọ, asopọ yẹ ki o rọ, ati lẹhinna ẹrọ idanwo iboju àlẹmọ. Awọn ifasoke submersible ni ao mu jade lati inu kanga fun fifọ ati itọju ni ibamu si Abala 5 lẹhin ọdun kan ti iṣẹ, tabi kere si ọdun kan ti iṣẹ ṣugbọn ọdun meji ti akoko omiwẹ, ati awọn ẹya ti o wọ ni yoo rọpo.

Ọja yii jẹ fifa ina mọnamọna submersible pẹlu iṣẹ ṣiṣe to dara julọ. Apẹrẹ alailẹgbẹ rẹ dara fun lilo ni awọn igba pupọ. Boya o jẹ lati ṣe idiwọ mọto lati didi ni igba otutu tabi lati yago fun ipata nigbati o ko ba lo fun igba pipẹ, fifa ina submersible yii le pade awọn iwulo rẹ fun itọju ohun elo. O rọrun lati ṣiṣẹ ati rọrun lati ṣetọju. Kan tẹle awọn igbesẹ inu iwe afọwọkọ fun itọju to tọ ati ibi ipamọ, eyiti o le fa igbesi aye iṣẹ ti ọja pẹ ni imunadoko. Gba fifa ina mọnamọna submersible bayi ki o jẹ ki iṣẹ rẹ rọra ati daradara siwaju sii!

01 Gbigbe omi kanga ti o jinlẹ

02 Giga-jinde omi ipese

03 oke omi ipese 

04 omi ẹṣọ

05 Ogbin irigeson

06 irigeson ọgba

07 odo omi gbigbemi

08 omi inu ile