200QJP Peep Well Submersible Pump

QJP series special fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are covered with alloy copper sleeve as lubricant, using water. Stainless steel sleeves replace ball bearings, avoiding the problem of easy rust of ball bearings and the problem of motor burning due to lack of oil wear. It is very suitable for music fountain, all models can be used horizontally.

This product uses three-phase AC 380V power supply (tolerance + 5%), 50HZ frequency (tolerance + 1%); the applicable water quality conditions for water temperature is not higher than 20 °C, solid impurities content (mass ratio) is not more than 0.01%, pH value (pH) is 6.5-8.5, hydrogen sulfide content is not more than 1.5mg/L, chloride ion content is not more than 400mg/L. The motor adopts closed or water sealed wet structure, before use must be filled with clean water to prevent virtual filled, and then tighten the water injection and air exhaust bolts, otherwise not to use. Submersible pump must be completely immersed in water to work, immersion depth shall not exceed 70 meters, the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The water in the well should be able to meet the water output and continuous operation of the submersible pump, the water output of the pump should be controlled at 0.7-1.2 times the rated flow. The well should be kept vertical, the submersible pump can not be used horizontally or overturned, only vertical installation. The submersible pump must be equipped with cables as required, and equipped with external overload protection device. The pump is strictly prohibited from no water load test.

 Well submersible pump is a kind of fresh water pump, it is strictly prohibited to dig new wells and pump mud and sand. The product adopts 380/50HZ voltage grade, other voltage grades shall not be used, and the submersible motor needs to be customized. Underground cables must use waterproof cables, and must be equipped with starting equipment, such as distribution box, etc. The starting equipment shall have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and no-load protection, etc. In abnormal cases, the protection device shall be tripped in time. When installed and used, the pump must be reliably grounded, it is prohibited to push and pull the switch when hands and feet are wet, and the power supply must be cut off before installation and maintenance of the pump. In the place where the pump is used, an obvious "anti-electric shock" sign must be set up. Before going down the well or installing, the motor must be filled with distilled water or non-corrosive clean cold water, and the water adding/discharge bolts must be tightened. When testing the pump on the ground, water must be injected into the pump chamber to lubricate the rubber bearings. The instantaneous start time shall not exceed one second to check whether the steering is correct, pay attention to safety, and prevent the pump from toppling and injuring people when it is upright. In strict accordance with the specified lift and flow range of the pump, to prevent the pump in low lift with large flow or in high lift with large traction, resulting in extreme wear of thrust bearings and other components, the motor overload and burn. After the pump into the well, the motor to the ground insulation resistance should be measured not less than 100MΩ. After the start, regular observation of voltage and current, and check whether the motor winding insulation meets the requirements; if the location of the pump storage temperature below freezing, should discharge the water in the motor cavity, to prevent water in the motor cavity ice and damage the motor due to low temperature.

ʻO ka hoʻomaka pōkole o ka hoʻolālā: ʻo ka ʻaoʻao pauma ka mea nui i haku ʻia me ka pahu paila, impeller, diversion shell, rubber bearing, check valve body (koho koho) a me nā mea ʻē aʻe. , noho alakaʻi alakaʻi haʻahaʻa, stator, rotor, alakaʻi alakaʻi luna noho, apo one, ʻāpana wai komo, kaula a me nā mea ʻē aʻe.

ʻO nā hiʻohiʻona nui o ka huahana:

 1, ʻO ke kaʻa he wai piha piha i ka wai submersible ʻekolu-phase asynchronous motor, piha ka pahu kaʻa i ka wai maʻemaʻe, hoʻohana ʻia e hōʻoluʻolu i ka mīkini a lubricate i ka bearing, hoʻohana ʻia ke kiʻi hoʻoponopono kaomi ma lalo o ka kaʻa e hoʻoponopono. ka hoʻonui a me ka ʻokoʻa o ke kaomi ʻana o ka wai i loko o ke kino ma muli o ka hoʻololi ʻana o ka piʻi ʻana o ka wela o ke kaʻa.

 2, I mea e pale aku ai i ke one i loko o ka wai punawai mai ke komo ʻana i ke kaʻa, ua hoʻolako ʻia ka ʻaoʻao o luna o ka pahu kaʻa me nā sila ʻaila ʻelua, a ua hoʻokomo ʻia kahi apo one e hana i kahi ʻano pale one.

 3, I mea e pale ʻole ai i ka holo ʻana o ka pahu pāpaʻi i ka wā e hoʻomaka ai, ua hoʻopili ʻia ka pahu pāpaʻi a me ka pahu kaʻa e ka hui ʻana, a ua hoʻokomo ʻia kahi pahu pahu kiʻekiʻe ma ka ʻaoʻao haʻahaʻa o ke kaʻa.

 4, ʻO ka lubrication o ka kaʻa a me ka pahū pahū he wai lubrication.

 5, Hana ʻia ka wili kaʻa kaʻa stator me ke ʻano kiʻekiʻe o ka submersible motor winding wire, me ka hana insulation kiʻekiʻe.

 6, Hoʻolālā ʻia ka paila e ka CAD kamepiula, me ka hana maʻalahi a me ka hana ʻenehana maikaʻi.

(1) Hoʻomākaukau ma mua o ke kau ʻana:
1. E nānā inā kūpono ka pauma submersible i nā kūlana hoʻohana a me ka laulā i ʻōlelo ʻia ma ka manual.
2. Ma ka hoʻohana ʻana i kahi obiect kaumaha me ke anawaena e like me ke anawaena o waho loa o ka pauma hoʻohaʻahaʻa, e ana inā hiki i ka inneldiameter o ka luawai ke hoʻokomo i ka pauma hoʻoheheʻe ʻia, a e ana i ka hoʻokō ʻana o ka hohonu i nā koi hoʻokomo.
3. E nānā i ka maʻemaʻe o ka luawai a me ka wai o ka pūnāwai. Mai hoʻohana i ka pauma uila e holoi ai i ka ʻōpala welor a me ka wai one no ka pale ʻana i ka pōʻino mua o ka pauma uila.
4. E nānā inā kūpono ke kūlana o ka hoʻopili welhead a inā hiki iā ia ke kū i ke kūlana o ka ʻāpana holoʻokoʻa.
5. E nānā inā ua paʻa a hoʻokomo pono ʻia nā ʻāpana pauma submersible e like me ke kiʻikuhi hui ma ka manual.
6. Wehe i ka wili wai a hoʻopiha i ka lua kaʻa me ka wai maʻemaʻe, ʻaʻole ʻino (e hoʻomaopopo. Ma hope o 12 mau hola o ka wai ʻana, ʻaʻole pono e emi ka pale insulation o ke kaʻa ma mua o 150M Q ke ana ʻia me kahi papa haʻalulu 500V.
7. Uea hui, e oki i ka lima wili 120mm mai kekahi welau o ke kaula i puka aku a me ka uwea like me ka pahi a ka mea uwila, a oki i ka loa o na uwea kumu ekolu ma ke ano hee, e ihi i ke kumu keleawe 20mm, e wili i ka oxide. papa ma ka waho o ka uwea keleawe me ka pahi a me ke one lole, a hookomo i na uwea pili elua i loko o palirs.Ma hope o nakinaki pono i ka papa me ka maikai keleawe uea, solder pono a paa, a me ke one o kekahi. burrs ma ka ʻili. A laila, no nā hui ʻekolu, e hoʻohana i ka lipine insulation polyvester e hoʻopili iā lākou ma ke ʻano semi hoʻopaʻa ʻia no ʻekolu ʻauʻau. E wīwī i nā ʻaoʻao ʻelua o ka papa wrapping a paʻa me ke kaula nyion, a laila e hoʻohana i ke ʻano semi-stacked e ʻōwili i ka lipine no ʻekolu papa. E uhi i ka outellayer me ke kiʻekiʻe-press insulation tape no ʻekolu papa. ʻO ka hope, e pelu i nā kaula ʻekolu a hoʻopaʻa pinepine iā lākou no nā papa ʻelima me ka lipine kaomi kiʻekiʻe. Pono e hoʻopaʻa paʻa ʻia kēlā me kēia papa, a pono e paʻa a paʻa nā hui interlayer e pale aku i ka wai mai ke komo ʻana a me ka hōʻino ʻana i ka insulation, Ma hope o ke kāwili ʻana, e hoʻoinu i ka wai i ka lumi wela o 20 'c no 12 mau hola, a e ana i ke kūpaʻa insulation me kahi papa haʻalulu. , ʻaʻole pono e emi ma lalo o 100M Ω

ʻO ke kiʻikuhi kaʻina hana uwila i hoʻopili ʻia penei:

8. E hoʻohana i ka multimeter no ka nānā ʻana inā pili ʻia nā uea ʻekolu ʻāpana a inā ʻaʻole kaulike ke kūpaʻa DC.
9. E nānā inā ua hoʻonui ʻia ka mana kaapuni a me ka mea hoʻololi, a laila hoʻohui i ke kī hoʻomalu overload a i ʻole nā ​​mea hoʻomaka. E nānā i ka Papa 2 no nā hi'ohi'ona kiko'ī, a laila, e ninini i ka bākeke wai i loko o ka pā wai mai ka puka wai e ho'oma'ama'a i ka pahu pahu i loko o ka pama, a laila e kau i ka pauma uwila i lalo i luna a pa'a. a e nānā inā pili ka hoʻokele me ka hōʻailona hoʻokele. Inā ʻaʻole, e hoʻololi i nā mea hoʻohui ʻelua o ke kaula ʻekolu. Inā hoʻohana ʻia i nā hanana kūikawā (e like me nā ʻauwai, nā ʻauwai, nā muliwai, nā loko, nā loko, a me nā mea ʻē aʻe), pono e hoʻopaʻa ʻia ka paila uila.

(2) Mea hoʻokomo a me nā mea hana:
1. Hoʻokahi mau kaulahao hāpai no ʻelua mau tona.
2. ʻO kahi tripod me ke kiʻekiʻe kū i lalo o ʻehā mau mika.
3. ʻElua kaula kau (wire ropes) hiki ke kaumaha i ke kaumaha ma mua o hoʻokahi tona (hiki ke halihali i ke kaumaha o ka pahu wai piha).
4. E hoʻouka i ʻelua mau paʻi (splints).
5. Nā wrenches, hammers, screwdrivers, uila a me nā mea kani, etc.

(3) Hoʻokomo ʻia ka pauma uila:
1. Hōʻike ʻia ke kiʻikuhi hoʻonohonoho o ka pauma uila submersible ma ka Figure 2. Hōʻike ʻia nā ana hoʻonohonoho kikoʻī ma ka Papa 3 "List of Installation Dimensions of the Submersible Electric Pump".

2. Hiki ke hoʻokiʻekiʻe pololei ʻia nā paila uila me ke poʻo ma lalo o 30 mika i loko o ka pūnāwai me ka hoʻohana ʻana i nā paipu a me nā kaula uwea a i ʻole nā ​​kaula hemp ʻē aʻe e hiki ai ke halihali i ke kaumaha piha o ka mīkini holoʻokoʻa, nā paipu wai, a me ka wai i loko o nā paipu.

3. ʻO nā pumps me ke poʻo i ʻoi aku ma mua o 30 mika e hoʻohana i nā paipu kila, a penei ka hoʻonohonoho ʻana:
①E hoʻohana i kahi pipili no ka hoʻopaʻa ʻana i ka ʻaoʻao o luna o ka ʻaoʻao o ka pauma wai (ua hoʻopili ʻia ke kaʻa a me ka pauma wai i kēia manawa), e hoʻokiʻekiʻe me ke kaulahao e kau ana, a nakinaki mālie i loko o ka luawai a kau i ka paʻi ma ke poʻo punawai a wehe i ke kaulahao. kaulahao e kau ana.
② E hoʻohana i nā paipu ʻē aʻe e hoʻopaʻa i ka paipu, e hoʻokiʻekiʻe me ke kaulahao e kau ana ma kahi mamao o 15 knm mai ka lehelehe, a e hoʻohaʻahaʻa mālie. Ma waena o ka flange paipu a me ka flange pump E hoʻopaʻa i ka pā hao a hoʻopaʻa i ka paipu a paʻa pono me nā bolts, nati a me nā mea holoi puna.
③ E hoʻokiʻekiʻe iki i ka pauma hoʻohaʻahaʻa, e wehe i ke kaula ma ka ʻaoʻao o luna o ka pā wai, e hoʻopaʻa paʻa i ke kaula i ka paipu wai me ka lipine plastik, a nakinaki mālie i lalo a kau ʻia ka paʻi ma ka luawai.
④E hoʻohana i ke ʻano like e hoʻopaʻa ai i nā paipu wai a pau i loko o ka pūnāwai.
⑤Ma hope o ka hoʻopili ʻia ʻana o ke kaula alakaʻi i waho i ka hoʻololi mana, ua hoʻopili ʻia i ka lako mana ʻekolu.

(4) Nā mea e nānā ai i ka wā e hoʻokomo ai:
1. Inā ʻike ʻia kahi mea hoʻopuʻi i ka wā o ka pahū ʻana, e hoʻohuli a huki paha i ka paipu wai no ka lanakila ʻana i ke kiko pahu. Inā ʻaʻole e holo nā ʻano hana like ʻole, e ʻoluʻolu, mai hoʻoikaika i ka pamu i lalo e pale aku i ka pōʻino o ka pauma uila a me ka luawai.
2. I ka wā o ka hoʻokomo ʻana, pono e kau ʻia kahi pā hao ma ka ʻaoʻao o kēlā me kēia paipu a paʻa pono.
3. Ke hoʻohaʻahaʻa ʻia ka paila wai i loko o ka pūnāwai, pono e hoʻokomo ʻia i waenakonu o ka paipu pūnāwai i mea e pale ai i ka holo ʻana o ka pamu i ka paia o ka pūnāwai no ka manawa lōʻihi, e hoʻonāwaliwali ai ka pamu a e kahili a wela ke kaʻa. .
4. E hoʻoholo i ka hohonu o ka paila wai a hiki i lalo o ka luawai e like me ke kahe ʻana o ke one a me ka lepo o ka luawai. Mai kanu i ka pamu i ka lepo. ʻO ka mamao mai ka pā wai a hiki i lalo o ka pūnāwai ʻaʻole i emi iho ma mua o 3 mika (e nānā i ke Kiʻi 2).
5. ʻAʻole emi ka hohonu o ke komo ʻana o ka wai ma lalo o 1-1.5 mika mai ke kiʻekiʻe o ka wai ikaika a hiki i ka node inlet wai (e nānā i ke Kiʻi 2). Inā ʻaʻole, hiki ke pohō maʻalahi nā bearings pump wai.
6. ʻAʻole hiki ke haʻahaʻa loa ka hāpai ʻana o ka paila wai. A i ʻole, pono e hoʻokomo ʻia kahi valve puka ma luna o ka pipeline wai punawai e hoʻomalu i ke kahe ʻana o ka paila ma ka helu kahe i helu ʻia e pale ai i ka hoʻonui ʻia ʻana o ke kaʻa a puhi ʻia ma muli o nā kahe kahe nui.
7. I ka holo ana o ka pauma wai, pono e hoomau ka puka ana o ka wai a me ke ano, pono ke kupaa (ma lalo o na kulana hana i heluia, ma ke ano, aole oi aku mamua o 10% o ka manawa i heluia), a aole e haalulu a walawala. Inā loaʻa kekahi mea ʻino, pono ke kāpae ʻia ka mīkini e ʻike i ke kumu a hoʻopau.
8. I ka wā e hoʻokomo ai, e hoʻolohe i ka hoʻonohonoho ʻana o ka uea hoʻopaʻa ʻia kaʻa (e nānā i ke Kiʻi 2). Inā he paipu kila ka paipu wai, e alakaʻi iā ia mai ka puʻu punawai; inā he paipu plastik ka paipu wai, e alakaʻi iā ia mai ka hōʻailona kumu o ka paila uila.

• 1. Ma hope o ka hoʻokomo ʻia ʻana o ka pauma submersible, e nānā i ke kūpaʻa insulation a me ka conduction ʻekolu-phase mai ka hoʻololi hou ʻana, e nānā inā hewa ka mea kani a me ka pilina o nā mea hoʻomaka, inā ʻaʻohe pilikia, hiki ke hoʻomaka ka mīkini hoʻokolokolo, a e nānā inā ʻoi aku ka nui o ka helu helu ʻana o ka mea kani i ka volta helu a me kēia manawa i kuhikuhi ʻia ma ka papa inoa ma hope o ka hoʻomaka ʻana, a nānā inā he walaʻau a me ka haʻalulu ʻana o ka pamu, a hoʻokomo i ka hana inā maʻamau nā mea a pau.
• 2. Ma hope o ka hana mua o ka paila no nā hola ʻehā, pono e pani ʻia ke kaʻa no ka hoʻāʻo ʻana i ke kūpaʻa insulation thermal me ka wikiwiki, a ʻaʻole e emi kona waiwai ma mua o 0.5 megaohm.
• 3. Ma hope o ka pani ʻia ʻana o ka pauma, pono e hoʻomaka ʻia ma hope o ʻelima mau minuke e pale i ke kolamu wai i loko o ka paipu mai ka hoʻihoʻi hou ʻana a me ka hoʻonui ʻana i ka mīkini kaʻa a me ke ahi.
• 4. Ma hope o ka hoʻokomoʻiaʻana o ka paila i loko o ka hana maʻamau, i mea e hoʻolōʻihi ai i kona ola lawelawe, pono e nānā inā he mau maʻamau ka volta hoʻolako, ka hana o kēia manawa a me ka pale pale. Inā ʻike ʻia kēia mau kūlana, pono e pani koke i ka pauma no ka hoʻoponopono pilikia.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Ke hāʻule nei ka pae wai ikaika i ka ʻāpana komo wai, e hoʻoulu ai i ka wai.
• 3 He haʻalulu koʻikoʻi ka haʻalulu a walaʻau paha ka pauma submersible.
• 4 ʻO ka haʻahaʻa haʻahaʻa ma mua o 340 volts.
• 5 Ua pau ka fuse.
• 6 Poino ka paipu wai.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1.Untie the cable tie, remove the pipeline part, and remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 This product is a submersible pump, which is suitable for various water areas, such as home, agriculture and industry.In order to prevent the motor from freezing in winter, be sure to discharge all the water in the pump chamber, and roll and tie the cable well.In addition, a room without corrosive substances and gases and with a temperature below 40 °C should be selected for storage.When not in use for a long time, special attention should be paid to the rust prevention of the submersible pump.This product is exquisitely designed and convenient to use, which can help users efficiently deal with various water needs, and is an ideal choice for your home and industrial water.

01 Hoʻokomo wai hohonu

02 Waiwai kiʻekiʻe

03 lako wai mauna

04 hale kiaʻi wai

05 Ka wai mahiai

06 ka hoʻoulu ʻana i ka māla

07 hoʻokomo wai kahawai

08 wai hale