200QJP Peep Well Submersible Pump

QJP series special fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are covered with alloy copper sleeve as lubricant, using water. Stainless steel sleeves replace ball bearings, avoiding the problem of easy rust of ball bearings and the problem of motor burning due to lack of oil wear. It is very suitable for music fountain, all models can be used horizontally.

This product uses three-phase AC 380V power supply (tolerance + 5%), 50HZ frequency (tolerance + 1%); the applicable water quality conditions for water temperature is not higher than 20 °C, solid impurities content (mass ratio) is not more than 0.01%, pH value (pH) is 6.5-8.5, hydrogen sulfide content is not more than 1.5mg/L, chloride ion content is not more than 400mg/L. The motor adopts closed or water sealed wet structure, before use must be filled with clean water to prevent virtual filled, and then tighten the water injection and air exhaust bolts, otherwise not to use. Submersible pump must be completely immersed in water to work, immersion depth shall not exceed 70 meters, the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The water in the well should be able to meet the water output and continuous operation of the submersible pump, the water output of the pump should be controlled at 0.7-1.2 times the rated flow. The well should be kept vertical, the submersible pump can not be used horizontally or overturned, only vertical installation. The submersible pump must be equipped with cables as required, and equipped with external overload protection device. The pump is strictly prohibited from no water load test.

 Well submersible pump is a kind of fresh water pump, it is strictly prohibited to dig new wells and pump mud and sand. The product adopts 380/50HZ voltage grade, other voltage grades shall not be used, and the submersible motor needs to be customized. Underground cables must use waterproof cables, and must be equipped with starting equipment, such as distribution box, etc. The starting equipment shall have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and no-load protection, etc. In abnormal cases, the protection device shall be tripped in time. When installed and used, the pump must be reliably grounded, it is prohibited to push and pull the switch when hands and feet are wet, and the power supply must be cut off before installation and maintenance of the pump. In the place where the pump is used, an obvious "anti-electric shock" sign must be set up. Before going down the well or installing, the motor must be filled with distilled water or non-corrosive clean cold water, and the water adding/discharge bolts must be tightened. When testing the pump on the ground, water must be injected into the pump chamber to lubricate the rubber bearings. The instantaneous start time shall not exceed one second to check whether the steering is correct, pay attention to safety, and prevent the pump from toppling and injuring people when it is upright. In strict accordance with the specified lift and flow range of the pump, to prevent the pump in low lift with large flow or in high lift with large traction, resulting in extreme wear of thrust bearings and other components, the motor overload and burn. After the pump into the well, the motor to the ground insulation resistance should be measured not less than 100MΩ. After the start, regular observation of voltage and current, and check whether the motor winding insulation meets the requirements; if the location of the pump storage temperature below freezing, should discharge the water in the motor cavity, to prevent water in the motor cavity ice and damage the motor due to low temperature.

Intshayelelo emfutshane yolwakhiwo: inxalenye yempompo yenziwe ikakhulu yimpompo yempompo, i-impeller, igobolondo le-diversion, i-rubber bearing, i-valve yokukhangela umzimba (indawo ezikhethiweyo) kunye nezinye izinto. , isihlalo esisezantsi esiphethe isikhokelo, i-stator, i-rotor, isihlalo esiphezulu sokuhamba kwesikhokelo, isanti yesanti, icandelo lokungena kwamanzi, ikhebula kunye nezinye izinto.

Iimpawu eziphambili zemveliso ziquka:

 I-1, i-motor ngamanzi azaliswe ngamanzi angaphantsi kwamanzi amanqanaba amathathu e-asynchronous motor, i-motor cavity igcwele amanzi acocekileyo, isetyenziselwa ukupholisa i-motor kunye nokuthambisa i-bearing, ifilimu elawula uxinzelelo ezantsi kwe-motor isetyenziselwa ukulungelelanisa. Ukwandiswa kunye nokwahlukana koxinzelelo loxinzelelo lwamanzi ngaphakathi emzimbeni obangelwa utshintsho lokunyuka kobushushu bemoto.

 I-2, Ukuthintela isanti kumanzi omthombo ekungeneni kwi-motor, isiphelo esiphezulu se-motor shaft sixhotywe ngamatywina amabini e-oyile, kunye nendandatho yesanti ifakwe ukwenza isakhiwo sokukhusela isanti.

 I-3, Ukuze uthintele i-shaft yepompo ukuba iqhube xa iqala, i-pump shaft kunye ne-motor shaft idibaniswe ngokudibanisa, kwaye i-top thrust bear ifakwe kwindawo engezantsi yemoto.

 I-4, I-lubrication ye-motor kunye ne-pump ephethe i-lubrication yamanzi.

 I-5, i-motor stator winding yenziwe nge-high-submersible motor winding wire, kunye nokusebenza okuphezulu kwe-insulation.

 I-6, ipompo yenzelwe i-CAD yekhompyutheni, kunye nesakhiwo esilula kunye nokusebenza kakuhle kwezobugcisa.

(1)Ulungiselelo phambi kofakelo:
1. Jonga ukuba impompo engaphantsi kwamanzi iyahlangabezana nemiqathango yokusetyenziswa kunye nobubanzi obuchazwe kwincwadana.
2. Ukusebenzisa i-obiect enzima ene-diameter elingana nobukhulu obungaphandle bedayamitha yempompo engaphantsi kwamanzi, linganisa ukuba i-inneldiameter ye-wellbore ingafanelana nempompo engaphantsi kwamanzi, kwaye ulinganise ukuba ubunzulu bomthombo buhlangabezana neemfuno zokufakela.
3. Jonga ukuba iqula licocekile na kunye nokuba amanzi amgxobhozo na. Ungaze usebenzise impompo yombane engaphantsi kwamanzi ukuhlamba udaka lwempompo ye-welor kunye namanzi esanti ukunqanda umonakalo ophambi kwexesha kwimpompo yombane engaphantsi kwamanzi.
4. Khangela ukuba indawo ye-welhead yokufakela i-clamp ifanelekile kwaye ingaba inokumelana nomgangatho weyunithi yonke.
5. Khangela ukuba izixhobo zempompo eziphantsi kwamanzi zigqityiwe kwaye zifakwe ngokufanelekileyo ngokwedayagram yendibano kwincwadana Susa isikrini sokucoca kwaye ujikelezise ukudibanisa ukuze ubone ukuba ijikeleza ngokuguquguqukayo.
6. Khupha isikrufu samanzi uze ugcwalise umngxuma wemoto ngamanzi acocekileyo, angadlekiyo (qaphela. qiniseka ukuba uyasifafa), uze uqinise isikrufu samanzi. Emva kweeyure ezili-12 zenaliti yamanzi, ukuxhathisa kwe-insulation ye-motor akufanele kube ngaphantsi kwe-150M Q xa kulinganiswa netafile yokungcangcazela ye-500V.
7. Umdibaniso wekheyibhile, unqumle umkhono werabha oyi-120mm kwelinye icala lentambo ephumayo kunye nentambo yokumatanisa enemela yomntu wombane uze ugxadazele ubude beengcingo ezintathu ezingundoqo ngendlela enyathelweyo, krazula umbindi wobhedu oyi-20mm, krazula ioksidi. umaleko ongaphandle kocingo lobhedu ngemela okanye ngelaphu lesanti, kwaye ufake iziphelo zocingo ezimbini eziqhagamshelweyo kwi palirs.Emva kokubopha umaleko ngokuqinileyo ngocingo olucolekileyo lobhedu, i-solder ngokucokisekileyo kwaye ngokuqinileyo, kunye nesanti yayo nayiphi na. amaqhuma phezu komhlaba. Emva koko, kumalungu amathathu, sebenzisa iteyiphu yokugquma i-polyvester ukuyisonga ngendlela epakishwe kabini kwizitya zokuhlambela ezintathu. Songa iziphelo ezibini zomaleko wokusonga ngokuqinileyo ngomsonto we-nyion, kwaye emva koko usebenzise indlela epakishwe kabini ukusonga iteyiphu kwiileya ezintathu. Songa i-outellayer ngetape yoxinzelelo oluphezulu lwe-insulation kwimigangatho emithathu. Ekugqibeleni, phinda udibanise imisonto emithathu kwaye uyibophe ngokuphindaphindiweyo kwi-fivelayers nge-tape yoxinzelelo oluphezulu. Umaleko ngamnye kufuneka ubotshelelwe ngokuqinileyo, kwaye amalungu e-interlayer kufuneka abe ngqongqo kwaye abe fimm ukukhusela amanzi ukuba angangeni kwaye wonakalise isigqubuthelo, Emva kokusonga, faka amanzi kwindawo yobushushu obungama-20 'c iiyure ezili-12, kwaye ulinganise ukuxhathisa ukugquma ngetafile eshukumayo. , ekufuneka ingabi ngaphantsi kwe-100M Ω

Umzobo oqhotyoshelweyo wenkqubo yokufaka iintambo zentambo umi ngolu hlobo lulandelayo:

8. Sebenzisa i-multimeter ukujonga ukuba ngaba iingcingo zesigaba sesithathu zidibaniswe kunye nokuba ukuchasana kwe-DC kuphantse kulinganiswe.
9. Khangela ukuba isekethe kunye nomthamo we-transformer ugcwele kakhulu, kwaye emva koko uqhagamshele i-switch yokukhusela okanye uqalise izixhobo. Jonga iTheyibhile yesi-2 kwiimodeli ezithile, kwaye emva koko galela ibhakethi lamanzi kwimpompo yamanzi ukusuka kwindawo yokupompoza amanzi ukuthambisa iibheringi zerabha kwimpompo, kwaye emva koko ubeke impompo yombane entywilayo ngokuthe tye kwaye izinzile.Qala (ungabi ngaphezu komzuzwana omnye) kwaye ujonge ukuba ngaba ulwalathiso lokuqhuba luyahambelana nophawu lokuqhuba. Ukuba akunjalo, tshintsha naziphi na izihlanganisi ezibini zesigaba sesithathu sentambo. Emva koko faka isihluzo kwaye ulungiselele ukuhla equleni. Ukuba isetyenziswe ngezihlandlo ezikhethekileyo (ezifana nemijelo, imisele, imilambo, amachibi, amachibi, njl. njl.), impompo yombane kufuneka isekelwe ngokuthembekileyo.

(2)Izixhobo zofakelo kunye nezixhobo:
1. Ipere enye yamatyathanga okuphakamisa ngaphezulu kweetoni ezimbini.
2. I-tripod enobude obuthe nkqo obungekho ngaphantsi kweemitha ezine.
3. Iintambo ezimbini ezijingayo (iintambo zocingo) ezinokuthwala ubunzima obungaphezu kwetoni enye (zinokuthwala ubunzima beseti epheleleyo yeempompo zamanzi).
4. Fakela izibini ezimbini zeeclamps (i-splints).
5. Izitshixo, izando, i-screwdrivers, izixhobo zombane kunye nezixhobo, njl.

(3)Ufakelo lwempompo yombane:
1. Umzobo wofakelo lwempompo yombane engaphantsi kwamanzi iboniswe kuMzobo 2. Imilinganiselo ethile yokufakela iboniswe kwiThebhile 3 "Uluhlu lweMilinganiselo yokuFakela iPump yoMbane ongaphantsi kwamanzi".

2. Iimpompo zombane ezingaphantsi kwamanzi ezinentloko engaphantsi kweemitha ezingama-30 zinokunyuswa ngokuthe ngqo equleni kusetyenziswa imibhobho kunye neentambo zocingo okanye ezinye iintambo zehemp ezinokuthwala ubunzima obupheleleyo bomatshini wonke, imibhobho yamanzi, kunye namanzi kwimibhobho.

3. Iipompo ezinentloko yeemitha ezingaphezu kwe-30 zisebenzisa iipayipi zensimbi, kwaye ulandelelwano lofakelo lulandelayo:
①Sebenzisa ibamba ukucinezela isiphelo esiphezulu sempompo yamanzi (injini kunye nempompo yamanzi sele idityanisiwe ngeli xesha), yiphakamise ngetsheyini ejingayo, kwaye uyibophe ngokukhawuleza equleni de ubeke isibambiso entloko kwaye uyisuse. ikhonkco elijingayo.
② Sebenzisa enye ipere yeziqhoboshi ukuqhobosha umbhobho, uwuphakamise ngetyathanga elijingayo 15 cm kude neflange, kwaye uwuhlise kancinane. Phakathi kweflange yombhobho kunye neflange yepompoFaka ipadi yerabha endaweni kwaye uqinise umbhobho kwaye umpompe ngokulinganayo ngeebholiti, iinati kunye newasher zasentwasahlobo.
③ Phakamisa kancinane impompo entywilayo emanzini, susa isithinteli esikwisiphelo esiphezulu sempompo yamanzi, qhina intambo ngokuqinileyo kumbhobho wamanzi ngeteyiphu yeplastiki, kwaye uyibophe kancinane de Ibamba libekwe emthonjeni.
④Sebenzisa indlela efanayo ukubopha yonke imibhobho yamanzi equleni.
⑤Emva kokuba ikhebula elikhokelayo liqhagamshelwe kwisitshixo solawulo, liqhagamshelwe kunikezelo lwamandla amanqanaba amathathu.

(4)Izinto ekufuneka uziqwalasele ngexesha lofakelo:
1. Ukuba i-jamming phenomenon ifunyenwe ngexesha lenkqubo yokupompa, jika okanye utsale umbhobho wamanzi ukuze unqobe i-jamming point. Ukuba imilinganiselo eyahlukeneyo ayisebenzi, nceda unganyanzeli impompo phantsi ukunqanda umonakalo kwimpompo yombane engaphantsi kwamanzi kunye nequla.
2. Ngethuba lofakelo, i-rubber pad kufuneka ifakwe kwi-flange yombhobho ngamnye kwaye iqiniswe ngokulinganayo.
3. Xa impompo yamanzi ithotywa equleni, kufuneka ibekwe embindini wombhobho wequla ukuthintela ukuba impompo ihambe ngaphaya kodonga lwequla ixesha elide, nto leyo ebangela ukuba impompo ingcangcazele kwaye imotor itshayele kwaye itshise. .
4. Qinisekisa ubunzulu bempompo yamanzi ukuya ezantsi kwequla ngokwesanti equkuqelayo kunye neemeko zentlenge equleni. Musa ukungcwaba impompo eludakeni. Umgama ukusuka kumpompo wamanzi ukuya ezantsi kwequla awukho ngaphantsi kweemitha ezi-3 (jonga umfanekiso 2).
5. Ubunzulu bokungena kwamanzi kwimpompo yamanzi kufuneka bungabi ngaphantsi kwe-1-1.5 yeemitha ukusuka kwinqanaba lamanzi aguquguqukayo ukuya kwindawo yokungena kwamanzi (jonga uMfanekiso 2). Ngaphandle koko, iibheringi zempompo zamanzi zinokonakala lula.
6. Ukunyuswa kwempompo yamanzi akunakuba phantsi kakhulu. Kungenjalo, ivalve yesango kufuneka ifakwe kumbhobho wamanzi osentloko yomthombo ukulawula ukuhamba kwempompo kwindawo yokuqukuqela ehleliweyo ukuthintela ukugcwala okugqithisileyo kwemoto kwaye itshiswe ngenxa yamazinga amakhulu okuhamba.
7. Xa umpompo wamanzi usebenza, ukukhutshwa kwamanzi kufuneka kuqhubeke kwaye nokuba, okwangoku kufuneka kuzinzile (phantsi kweemeko zokusebenza ezilinganisiweyo, ngokuqhelekileyo akukho ngaphezu kwe-10% ye-current rated current), kwaye akufanele kubekho ukungcangcazela okanye ingxolo. Ukuba kukho nakuphi na ukungaqhelekanga, umatshini kufuneka umiswe ukufumanisa unobangela kwaye upheliswe.
8. Xa ufaka, qwa lasela ukusetwa kwe-motor grounding wire (jonga umfanekiso 2). Xa umbhobho wamanzi ungumbhobho wentsimbi, yiholele kwi-clamp ye-wellhead clamp; xa umbhobho wamanzi ungumbhobho weplastiki, ukhokele ukusuka kwindawo yokubeka ipompo yombane.

• 1.Emva kokuba i-submersible impompo ifakwe, khangela ukuchasana kwe-insulation kunye nesigaba sesithathu sokuqhuba ukusuka kwitshintshi kwakhona, khangela ukuba isixhobo kunye nokudityaniswa kwezixhobo zokuqala zingalunganga, ukuba akukho ngxaki, umatshini wokulinga unokuqaliswa, kwaye uqaphele ukuba ukufundwa kwesalathisi sesixhobo kudlula i-voltage elinganisiweyo kunye nekhoyo ngoku echazwe kwi-nameplate emva kokuqala, kwaye uqaphele ukuba ipompo inesandi kunye ne-vibration phenomenon, kwaye ifakwe ekusebenzeni ukuba yonke into iyinto eqhelekileyo.
• I-2.Emva kokusebenza kokuqala kompompo kwiiyure ezine, i-motor kufuneka ivalwe ukuvavanya ukuchasana kwe-thermal insulation ngokukhawuleza, kwaye ixabiso layo akufanele libe ngaphantsi kwe-0.5 megaohm.
• 3.Emva kokuba ipompo ivaliwe, kufuneka iqalwe emva kwemizuzu emihlanu ukukhusela ikholomu yamanzi kumbhobho ukuba iphinde ihlaziywe ngokupheleleyo kwaye ibangele umbane ogqithiseleyo kunye nokutshiswa.
• 4.Emva kokuba ipompo ifakwe ekusebenzeni okuqhelekileyo, ukwenzela ukwandisa ubomi bayo benkonzo, kuyimfuneko ukujonga ukuba i-voltage yokubonelela, ukusebenza ngoku kunye nokuchasana kwe-insulation kuqhelekileyo rhoqo. Ukuba le miqathango ilandelayo ifunyenwe, impompo kufuneka ivalwe ngokukhawuleza ukulungisa ingxaki.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Umgangatho wamanzi oguquguqukayo wehla ukuya kwindawo yokungena kwamanzi, okubangela ukuba amanzi aphumle.
• 3 Impompo entywilayo phantsi inongcangcazelo olumandla okanye ingxolo.
• 4 Umbane wokubonelela ungaphantsi kwe-340 volts.
• 5 Ifuse iyatshiswa.
• 6 Umbhobho wonikezelo lwamanzi wonakalisiwe.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1.Untie the cable tie, remove the pipeline part, and remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 This product is a submersible pump, which is suitable for various water areas, such as home, agriculture and industry.In order to prevent the motor from freezing in winter, be sure to discharge all the water in the pump chamber, and roll and tie the cable well.In addition, a room without corrosive substances and gases and with a temperature below 40 °C should be selected for storage.When not in use for a long time, special attention should be paid to the rust prevention of the submersible pump.This product is exquisitely designed and convenient to use, which can help users efficiently deal with various water needs, and is an ideal choice for your home and industrial water.

01 Ukusela amanzi kwiqula elinzulu

02 Ubonelelo lwamanzi olukwizinga eliphezulu

03 unikezelo lwamanzi entabeni

04 amanzi enqaba

05 Ukunkcenkceshela kwezolimo

06 ukunkcenkceshela egadini

07 amanzi omlambo

08 amanzi asekhaya