300QJP Peep Well Submersible Pump

QJP series special fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are covered with alloy copper sleeves as lubricant. Stainless steel sleeves replace ball bearings, avoiding the problem of easy rust of ball bearings and burnout caused by motor lack of oil wear. Most suitable for music fountains, all models can be used flat.

The product is powered by three-phase AC 380V power supply, 50HZ pump, suitable for water temperature is not higher than 20 °C, solid impurities content is not greater than 0.01%, PH value between 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L water quality conditions. The product adopts closed or water-filled wet structure of the motor, before use the submersible motor chamber filled with clean water to prevent the occurrence of virtual filling. The submersible pump must be completely immersed in water operation, penetration depth shall not exceed 70 meters, to the bottom of the well distance shall not be less than 3 meters. The water flow in the well must meet the water requirements of the submersible pump and continuous operation, and the water output of the pump is controlled between 0.7-1.2 times the rated flow. The well should be vertical and the submersible pump can only be placed vertically, not horizontal or upside down. The submersible pump must be equipped with cables and external overload protection devices as required. It is strictly prohibited to conduct no-load test of the pump without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, hentitra araka ny fepetra ny paompy fanandratana, mikoriana isan-karazany ny fampiasana, mba hisorohana ny fikorianan'ny ambany na ny fiakarana avo pumping hery, ny fanosehana mitondra sy ny ampahany hafa amin'ny fitafy, ny maotera be loatra may.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100MΩ, after the start to observe the voltage and current, check the motor winding insulation, whether it meets the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature motor

The pump parts of this product are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The product adopts water immersion wet three-phase asynchronous motor, the motor cavity is full of clean water, used to cool the motor and lubricate the bearing. The pressure regulating diaphragm set at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the water inside the body caused by the temperature rise of the motor. In order to prevent the sand particles from entering the motor, the upper end of the motor shaft extension is installed with two oil seals, and the sand ring is set to form a sand blocking structure. At the same time, in order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft through the coupling, and the bottom of the motor is equipped with a thrust bearing. The motor and pump bearing are lubricated by water. The stator winding of the motor adopts high quality submersible motor winding with high insulation performance. The pump design adopts computer CAD, with simple structure and good technical performance.

(1) Fiomanana alohan'ny fametrahana:
1. Hamarino raha mahafeno ny fepetra fampiasana sy ny habaka voafaritra ao amin'ny boky ny paompy submersible.
2. Mampiasa obiect mavesatra miaraka amin'ny savaivony mitovy amin'ny savaivony ivelany ambony indrindra amin'ny paompy submersible, refeso raha mety hifanaraka amin'ny paompy submersible ny savaivony amin'ny lavaka fantsakana, ary refesina raha mahafeno ny fepetra takiana amin'ny fametrahana ny halaliny.
3. Hamarino raha madio ny lavaka fantsakana ary ny rano fantsakana dia feno rano. Aza mampiasa paompy elektrika azo atsoboka mihitsy mba hanasana ny fotaka sy ny rano fasika mba hisorohana ny fahasimbana aloha loatra amin'ny paompy elektrika.
4. Hamarino raha mety ny toerana misy ny clamp fametrahana welhead ary mahatanty ny kalitaon'ny vondrona manontolo.
5. Hamarino raha toa ka feno sy apetraka araka ny tokony ho izy ny singa ao amin'ny paompy submersible araka ny kisarisary ao amin'ny boky torolalana.
6. Esory ny visy ary fenoy rano madio tsy misy korontanina ny lavaky ny môtô (mariho. Ataovy azo antoka ny famenoana azy), ary henjana ny vy. Taorian'ny 12 ora ny tsindrona rano, ny insulation fanoherana ny maotera dia tsy tokony ho latsaky ny 150M Q rehefa refesina amin'ny 500V nihozongozona latabatra.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Toy izao manaraka izao ny diagrama fizotry ny fizotry ny tariby tariby mifamatotra:

8. Mampiasà multimeter mba hijerena raha mifandray ny tariby telo-dingana ary sao dia mifandanja ny fanoherana DC.
9. Jereo raha be loatra ny fahaizan'ny circuit sy ny transformer, ary ampifandraiso amin'ny fiatoana fiarovana na fitaovana fanombohana avy eo. Jereo ny tabilao 2 ho an'ny maodely manokana, ary avy eo dia arotsaho ao anaty paompy rano avy amin'ny fivoahan'ny paompy rano ny siny mba hanesorana ny fingotra ao amin'ny paompy, ary avy eo dia apetraho mitsangana sy miorim-paka ny paompy elektrika an-drano. ary jereo raha mifanaraka amin'ny famantarana ny familiana ny fitarihana. Raha tsy izany dia ampifamadiho ny mpampitohy roa amin'ny tariby misy dingana telo. Avy eo apetraho ny sivana ary miomàna hidina amin'ny fantsakana. Raha ampiasaina amin'ny fotoana manokana (toy ny tatatra, tatatra, renirano, dobo, dobo, sns.), Ny paompy elektrika dia tsy maintsy miorina tsara.

(2) Fametrahana fitaovana sy fitaovana:
1. Rojo fanandratana roa mihoatra ny roa taonina.
2. Tripod misy haavo mitsangana tsy latsaky ny efatra metatra.
3. Tady mihantona roa (tady tariby) izay mahazaka lanja mihoatra ny iray taonina (mahazaka ny lanjan'ny paompin-drano feno).
4. Mametraka clamp roa (splints).
5. Wrenches, tantanana, screwdrivers, fitaovana elektrika sy fitaovana, sns.

(3) Fametrahana paompy elektrika:
1. Ny sarin'ny fametrahana ny paompy elektrika an-tsokosoko dia aseho amin'ny sary 2. Ny refy fametrahana manokana dia aseho amin'ny tabilao 3 "Lisitry ny haben'ny fametrahana ny paompy elektrika azo ampiasaina".

2. Ny paompy elektrika azo atsoboka amin'ny lohany latsaky ny 30 metatra dia azo atsangana mivantana ao amin'ny fantsakana amin'ny fampiasana hoses sy tady tariby na tady hemp hafa izay mahazaka ny lanjan'ny milina iray manontolo, ny fantson-drano ary ny rano ao anaty fantsona.

3. Ny paompy manana loha mihoatra ny 30 metatra dia mampiasa fantsona vy, ary ny filaharan'ny fametrahana dia toy izao manaraka izao:
①Mampiasà clamp hanintonana ny tendrony ambony amin'ny ampahany amin'ny paompy rano (efa mifandray ny motera sy ny paompy rano amin'izao fotoana izao), atsangano amin'ny rojo mihantona, ary afehezo tsikelikely ao anaty lavaka fantsakana mandra-pametraka ny fametahana eo amin'ny lohan'ny fantsakana ary esory rojo mihantona.
② Mampiasà fametahana roa hafa hamehezana sodina, atsangano amin'ny rojo mihantona eo amin'ny 15 sm miala ny flange, ary ampidino tsikelikely. Eo anelanelan'ny flange pipe sy flange paompyApetraho eo amin'ny toerany ny pad fingotra ary henjana ny sodina ary paompy mitovy amin'ny bolt, voanjo ary mpanasa lohataona.
③ Asandrato kely ny paompin-drano, esory ny fametahana eo amin'ny tendrony ambony amin'ny paompy rano, afehezo mafy amin'ny fantsona plastika ny tariby, ary afehezo tsikelikely mandra-pametraka ny fametahana eo amin'ny lohan'ny fantsakana.
④Mampiasà fomba mitovy amin'ny famatorana ny fantsona rehetra ao anaty lavaka fantsakana.
⑤Rehefa mifandray amin'ny tariby fanaraha-maso ny tariby mitarika, dia mifandray amin'ny famatsiana herinaratra amin'ny dingana telo izany.

(4) Zavatra tokony homarihina mandritra ny fametrahana:
1. Raha toa ka misy trangan-javatra misy fitohanana hita mandritra ny fizotry ny paompy, atodiho na sintonina ny fantson-drano mba hialana amin'ny teboka mikorontana. Raha mbola tsy mandeha ny fepetra isan-karazany, azafadyAza terena hidina ny paompy mba hisorohana ny fahasimban'ny paompy elektrika sy ny fantsakana.
2. Mandritra ny fametrahana dia tokony hapetraka eo amin'ny sisin'ny sodina tsirairay ny pad fingotra ary hamafisina tsara.
3. Rehefa ampidinina ao anaty fantsakana ny paompy rano, dia tokony hapetraka eo afovoan'ny fantsakana izany mba hisorohana ny paompy tsy hianjera amin'ny rindrin'ny fantsakana mandritra ny fotoana maharitra, ka mahatonga ny paompy hihovitrovitra ary ny motera hifafa sy handoro. .
4. Farito ny halalin'ny paompin-drano mankany amin'ny fanambanin'ny fantsakana araka ny toetry ny fasika mikoriana sy ny fotaka. Aza alevina ao anaty fotaka ny paompy. Ny halaviran'ny paompin-drano mankany amin'ny fanambanin'ny fantsakana amin'ny ankapobeny dia tsy latsaky ny 3 metatra (jereo ny sary 2).
5. Ny halalin'ny rano miditra amin'ny paompy dia tsy tokony ho latsaky ny 1-1,5 metatra avy amin'ny haavon'ny rano mavitrika mankany amin'ny node fampidirana rano (jereo ny sary 2). Raha tsy izany dia mety ho simba mora foana ny paompy rano.
6. Tsy tokony ho ambany loatra ny fiakaran'ny paompy rano. Raha tsy izany, mila asiana valva vavahady eo amin'ny fantson-drano amin'ny lohan'ny fantsakana mba hifehezana ny fikorianan'ny paompy eo amin'ny toerana misy naoty mba hisorohana ny motera tsy ho be loatra sy ho may noho ny tahan'ny fikorianan'ny rivotra.
7. Rehefa mandeha ny paompy rano, ny fivoahan'ny rano dia tokony ho mitohy ary na dia, ny ankehitriny dia tokony ho marin-toerana (eo ambanin'ny fepetra miasa, amin'ny ankapobeny tsy mihoatra ny 10% ny naoty ankehitriny), ary tsy tokony hisy hovitrovitra na tabataba. Raha misy tsy mety dia tokony hajanona ny milina mba hahitana ny antony sy hanafoanana izany.
8. Rehefa mametraka, tandremo tsara ny fametrahana ny tariby fanodinkodinana maotera (jereo ny sary 2). Raha sodina vy ny fantsona rano, dia tariho avy amin'ny fantson-drano; rehefa fantsona plastika ny fantsona rano dia tariho avy amin'ny marika fototra amin'ny paompy elektrika.

5. 1 submersible pump installation is complete, re-check the insulation resistance and three-phase conduction from the switch, check the instrument and start the equipment connection error, if there is no problem, can start the trial, after the start of the instrument indicating readings whether more than the nameplate stipulated rated voltage and current, observe the pump noise and vibration phenomenon, everything is normal can be put into operation.
6. 2 paompy asa nandritra ny efatra ora voalohany, dia tokony ho nakatona haingana hizaha toetra ny mafana insulation fanoherana ny maotera, ny sandany dia tsy tokony ho latsaky ny 0,5 megaohm.
7. 3 pump shutdown, should be started after an interval of five minutes, to prevent the water column in the pipe has not completely reflux caused by excessive motor current and burnout.
8. 4 paompy ho amin'ny asa ara-dalàna, mba hanalava ny asa fanompoana, mba hanamarina ny famatsiana malefaka, miasa amin'izao fotoana izao sy ny insulation fanoherana dia ara-dalàna, raha hita ny toe-javatra manaraka ireto, dia tokony hanakatona avy hatrany troubleshooting.
9.  
10. 1 amin'ny fepetra nomena, ny ankehitriny dia mihoatra ny 20%.
11. 2 ny haavon'ny rano mavitrika mankany amin'ny faritra fidirana amin'ny rano, miteraka rano miato.
12. 3 submersible paompy hovitrovitra na tabataba mafy.
13. 4 famatsiana malefaka dia ambany noho ny 340 volts.
14. 5 fuse nandoro dingana iray.
15. Fahasimban'ny fantsona rano 6.
16. 7 maotera amin'ny fanoherana ny insulation mafana dia latsaky ny 0.5 megaohm.
17.  
18. 5. This product is a high-quality submersible pump, in addition to the efficient pumping function, but also easy to maintain and clean. The disassembly process is simple and clear, just follow the steps to untie the cable, remove the pipeline part, take off the line protection plate, loosen the water discharge bolt, remove the filter and loosen the fixing screw, separate the pump and the motor, and then remove the parts of the pump and the motor, pay attention to avoid damage. When assembling, thoroughly clean the components, apply sealant on the mating surface and fasteners, and then assemble in the opposite order. Every year or two years after immersion, check in accordance with the steps, replace the worn parts. This product has a reasonable structure, easy to operate, and is suitable for various occasions for pump needs.

 1, esory ny rano ao amin'ny lavaka maotera (indrindra amin'ny ririnina mba hisorohana ny motera tsy hivaingana), ary afehezo tsara ny tariby.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 3, ny fampiasana maharitra dia tokony handinika ny fisorohana ny harafesina amin'ny paompy submersible.

01 Fantsakana rano lalina

02 Famatsiana rano avo

03 famatsiana rano an-tendrombohitra 

04 rano tilikambo

05 Fanondrahana fambolena

06 fanondrahana zaridaina

07 rano fisotro madio

08 rano ao an-trano