125QJR Paompy Fantsakana lalina

Suitable for underground hot water mining with water temperature below 100°C, with heat resistance, corrosion resistance, aging resistance and other characteristics

This product is a powerful three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%) electric pump, suitable for all kinds of occasions need high-power pump. Its design considers a variety of water quality factors, including water temperature not higher than 20 °C, solid impurities content is not greater than 0.01%, PH value is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L, etc. The product adopts a closed or water immersion wet structure of the motor, before use in the submersible motor chamber filled with clean water to prevent empty fill. Requirements in strict accordance with the requirements of the matching cable and equipped with external overload protection device. To ensure stable operation, the submersible pump must be completely immersed in water operation, the insertion depth shall not exceed 70 meters, and the distance from the bottom of the well shall not be less than 3 meters. In addition, the pump shall not be a no-load test before start. In general, this product has the characteristics of high efficiency and stability, suitable for a variety of pump tasks in harsh environment.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, strictly according to the provisions of the pump lift, flow range of use, to prevent low flow or high lift pumping force, the thrust bearing and other parts of the wear, the motor overload burned 6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the water in the motor cavity, prevent the motor cavity water ice damage caused by low temperature.

The pump parts are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The motor is a water-filled submersible three-phase asynchronous motor, which is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the difference in internal water expansion and contraction pressure caused by the temperature rise of the motor. In order to prevent the sand in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft through a coupling, and a thrust bearing is installed at the lower part of the motor. The lubrication of the motor and the pump bearing is water lubrication. The stator winding of the motor adopts high quality submersible motor winding wire, with high insulation performance. The pump adopts computer CAD design, with simple structure and excellent technical performance.

(1) Fiomanana alohan'ny fametrahana:
1. Hamarino raha mahafeno ny fepetra fampiasana sy ny habaka voafaritra ao amin'ny boky ny paompy submersible.
2. Mampiasa obiect mavesatra miaraka amin'ny savaivony mitovy amin'ny savaivony ivelany ambony indrindra amin'ny paompy submersible, refeso raha mety hifanaraka amin'ny paompy submersible ny savaivony amin'ny lavaka fantsakana, ary refesina raha mahafeno ny fepetra takiana amin'ny fametrahana ny halaliny.
3. Hamarino raha madio ny lavaka fantsakana ary ny rano fantsakana dia feno rano. Aza mampiasa paompy elektrika azo atsoboka mihitsy mba hanasana ny fotaka sy ny rano fasika mba hisorohana ny fahasimbana aloha loatra amin'ny paompy elektrika.
4. Hamarino raha mety ny toerana misy ny clamp fametrahana welhead ary mahatanty ny kalitaon'ny vondrona manontolo.
5. Hamarino raha toa ka feno sy apetraka araka ny tokony ho izy ny singa ao amin'ny paompy submersible araka ny kisarisary ao amin'ny boky torolalana.
6. Esory ny visy ary fenoy rano madio tsy misy korontanina ny lavaky ny môtô (mariho. Ataovy azo antoka ny famenoana azy), ary henjana ny vy. Taorian'ny 12 ora ny tsindrona rano, ny insulation fanoherana ny maotera dia tsy tokony ho latsaky ny 150M Q rehefa refesina amin'ny 500V nihozongozona latabatra.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Toy izao manaraka izao ny diagrama fizotry ny fizotry ny tariby tariby mifamatotra:

8. Mampiasà multimeter mba hijerena raha mifandray ny tariby telo-dingana ary sao dia mifandanja ny fanoherana DC.
9. Jereo raha be loatra ny fahaizan'ny circuit sy ny transformer, ary ampifandraiso amin'ny fiatoana fiarovana na fitaovana fanombohana avy eo. Jereo ny tabilao 2 ho an'ny maodely manokana, ary avy eo dia arotsaho ao anaty paompy rano avy amin'ny fivoahan'ny paompy rano ny siny mba hanesorana ny fingotra ao amin'ny paompy, ary avy eo dia apetraho mitsangana sy miorim-paka ny paompy elektrika an-drano. ary jereo raha mifanaraka amin'ny famantarana ny familiana ny fitarihana. Raha tsy izany dia ampifamadiho ny mpampitohy roa amin'ny tariby misy dingana telo. Avy eo apetraho ny sivana ary miomàna hidina amin'ny fantsakana. Raha ampiasaina amin'ny fotoana manokana (toy ny tatatra, tatatra, renirano, dobo, dobo, sns.), Ny paompy elektrika dia tsy maintsy miorina tsara.

(2) Fametrahana fitaovana sy fitaovana:
1. Rojo fanandratana roa mihoatra ny roa taonina.
2. Tripod misy haavo mitsangana tsy latsaky ny efatra metatra.
3. Tady mihantona roa (tady tariby) izay mahazaka lanja mihoatra ny iray taonina (mahazaka ny lanjan'ny paompin-drano feno).
4. Mametraka clamp roa (splints).
5. Wrenches, tantanana, screwdrivers, fitaovana elektrika sy fitaovana, sns.

(3) Fametrahana paompy elektrika:
1. Ny sarin'ny fametrahana ny paompy elektrika an-tsokosoko dia aseho amin'ny sary 2. Ny refy fametrahana manokana dia aseho amin'ny tabilao 3 "Lisitry ny haben'ny fametrahana ny paompy elektrika azo ampiasaina".

2. Ny paompy elektrika azo atsoboka amin'ny lohany latsaky ny 30 metatra dia azo atsangana mivantana ao amin'ny fantsakana amin'ny fampiasana hoses sy tady tariby na tady hemp hafa izay mahazaka ny lanjan'ny milina iray manontolo, ny fantson-drano ary ny rano ao anaty fantsona.

3. Ny paompy manana loha mihoatra ny 30 metatra dia mampiasa fantsona vy, ary ny filaharan'ny fametrahana dia toy izao manaraka izao:
①Mampiasà clamp hanintonana ny tendrony ambony amin'ny ampahany amin'ny paompy rano (efa mifandray ny motera sy ny paompy rano amin'izao fotoana izao), atsangano amin'ny rojo mihantona, ary afehezo tsikelikely ao anaty lavaka fantsakana mandra-pametraka ny fametahana eo amin'ny lohan'ny fantsakana ary esory rojo mihantona.
② Mampiasà fametahana roa hafa hamehezana sodina, atsangano amin'ny rojo mihantona eo amin'ny 15 sm miala ny flange, ary ampidino tsikelikely. Eo anelanelan'ny flange pipe sy flange paompyApetraho eo amin'ny toerany ny pad fingotra ary henjana ny sodina ary paompy mitovy amin'ny bolt, voanjo ary mpanasa lohataona.
③ Asandrato kely ny paompin-drano, esory ny fametahana eo amin'ny tendrony ambony amin'ny paompy rano, afehezo mafy amin'ny fantsona plastika ny tariby, ary afehezo tsikelikely mandra-pametraka ny fametahana eo amin'ny lohan'ny fantsakana.
④Mampiasà fomba mitovy amin'ny famatorana ny fantsona rehetra ao anaty lavaka fantsakana.
⑤Rehefa mifandray amin'ny tariby fanaraha-maso ny tariby mitarika, dia mifandray amin'ny famatsiana herinaratra amin'ny dingana telo izany.

(4) Zavatra tokony homarihina mandritra ny fametrahana:
1. Raha toa ka misy trangan-javatra misy fitohanana hita mandritra ny fizotry ny paompy, atodiho na sintonina ny fantson-drano mba hialana amin'ny teboka mikorontana. Raha mbola tsy mandeha ny fepetra isan-karazany, azafadyAza terena hidina ny paompy mba hisorohana ny fahasimban'ny paompy elektrika sy ny fantsakana.
2. Mandritra ny fametrahana dia tokony hapetraka eo amin'ny sisin'ny sodina tsirairay ny pad fingotra ary hamafisina tsara.
3. Rehefa ampidinina ao anaty fantsakana ny paompy rano, dia tokony hapetraka eo afovoan'ny fantsakana izany mba hisorohana ny paompy tsy hianjera amin'ny rindrin'ny fantsakana mandritra ny fotoana maharitra, ka mahatonga ny paompy hihovitrovitra ary ny motera hifafa sy handoro. .
4. Farito ny halalin'ny paompin-drano mankany amin'ny fanambanin'ny fantsakana araka ny toetry ny fasika mikoriana sy ny fotaka. Aza alevina ao anaty fotaka ny paompy. Ny halaviran'ny paompin-drano mankany amin'ny fanambanin'ny fantsakana amin'ny ankapobeny dia tsy latsaky ny 3 metatra (jereo ny sary 2).
5. Ny halalin'ny rano miditra amin'ny paompy dia tsy tokony ho latsaky ny 1-1,5 metatra avy amin'ny haavon'ny rano mavitrika mankany amin'ny node fampidirana rano (jereo ny sary 2). Raha tsy izany dia mety ho simba mora foana ny paompy rano.
6. Tsy tokony ho ambany loatra ny fiakaran'ny paompy rano. Raha tsy izany, mila asiana valva vavahady eo amin'ny fantson-drano amin'ny lohan'ny fantsakana mba hifehezana ny fikorianan'ny paompy eo amin'ny toerana misy naoty mba hisorohana ny motera tsy ho be loatra sy ho may noho ny tahan'ny fikorianan'ny rivotra.
7. Rehefa mandeha ny paompy rano, ny fivoahan'ny rano dia tokony ho mitohy ary na dia, ny ankehitriny dia tokony ho marin-toerana (eo ambanin'ny fepetra miasa, amin'ny ankapobeny tsy mihoatra ny 10% ny naoty ankehitriny), ary tsy tokony hisy hovitrovitra na tabataba. Raha misy tsy mety dia tokony hajanona ny milina mba hahitana ny antony sy hanafoanana izany.
8. Rehefa mametraka, tandremo tsara ny fametrahana ny tariby fanodinkodinana maotera (jereo ny sary 2). Raha sodina vy ny fantsona rano, dia tariho avy amin'ny fantson-drano; rehefa fantsona plastika ny fantsona rano dia tariho avy amin'ny marika fototra amin'ny paompy elektrika.

• （1）With the continuous development of modern technology, submersible pumps play a crucial role in the field of pumps. After installing the submersible pump, check the insulation resistance and three-phase continuity repeatedly to ensure that there are no errors in the connection between the instrument and the starting equipment. If everything is normal, the test equipment can be started. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, pay attention to observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. After the pump runs for four hours for the first time, it should be closed and the thermal insulation resistance of the motor should be tested quickly, and its value should not be less than 0.5 megaohms. After stopping the pump, restart it after five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to overcurrent. After the pump is running normally, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the equipment should be shut down immediately to troubleshoot. The current exceeds 20% under the rated working conditions; the dynamic water level drops to the inlet section, resulting in intermittent drainage; the submersible pump vibrates violently or makes noisy sounds; the supply voltage is lower than 340 volts; any fuse is broken; the water pipe is damaged; The thermal insulation resistance between the motor and the ground is less than 0.5 megaohm.These recommended operating procedures and safety measures ensure the safe operation of the submersible pump, prolong the service life of the equipment, and provide users with a reliable pump choice.
•  
• （2）Unit disassembly:
• 1 untie the cable tie, remove the pipeline part, remove the wire plate.
• 2 unscrew the water release bolt, put the water in the motor chamber.
• 3 remove the filter, loose the fixing screw of the motor shaft on the coupling.
• 4 unscrew the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5 the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending the pump shaft and various bumps in the disassembly process.
• 6 the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nut, base, shaft head lock nut, thrust plate, key, lower guide bearing seat, double head bolt from the bottom of the motor in turn. Then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7 unit assembly: Before assembly, the rust and dirt of the parts should be cleaned, and the mating surfaces and fasteners should be coated with sealant. Then they should be assembled in the reverse order of disassembly (the up and down momentum of the motor shaft is about 1 mm after assembly). After assembly, the coupling should be flexible, and then the filter screen test machine.
•  
• （3）The submersible pump should be dismantled and repaired according to Article 5 for each operation year, or less than one year, but the submersible time has reached two years, and the worn parts should be replaced.

 1, esory ny rano ao amin'ny lavaka maotera (indrindra amin'ny ririnina mba hisorohana ny motera tsy hivaingana), ary afehezo tsara ny tariby.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 3, ny fampiasana maharitra dia tokony handinika ny fisorohana ny harafesina amin'ny paompy submersible.

01 Fantsakana rano lalina

02 Famatsiana rano avo

03 famatsiana rano an-tendrombohitra 

04 rano tilikambo

05 Fanondrahana fambolena

06 fanondrahana zaridaina

07 rano fisotro madio

08 rano ao an-trano