Caidéal Intumtha 300QJP Peep Well

QJP series special fountain pump is a special fountain pump developed by our factory. The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, has good magnetic conductivity, and does not produce heat when starting frequently. The two ends of the motor rotor are covered with alloy copper sleeves as lubricant. Stainless steel sleeves replace ball bearings, avoiding the problem of easy rust of ball bearings and burnout caused by motor lack of oil wear. Most suitable for music fountains, all models can be used flat.

The product is powered by three-phase AC 380V power supply, 50HZ pump, suitable for water temperature is not higher than 20 °C, solid impurities content is not greater than 0.01%, PH value between 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L water quality conditions. The product adopts closed or water-filled wet structure of the motor, before use the submersible motor chamber filled with clean water to prevent the occurrence of virtual filling. The submersible pump must be completely immersed in water operation, penetration depth shall not exceed 70 meters, to the bottom of the well distance shall not be less than 3 meters. The water flow in the well must meet the water requirements of the submersible pump and continuous operation, and the water output of the pump is controlled between 0.7-1.2 times the rated flow. The well should be vertical and the submersible pump can only be placed vertically, not horizontal or upside down. The submersible pump must be equipped with cables and external overload protection devices as required. It is strictly prohibited to conduct no-load test of the pump without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, go docht de réir fhorálacha an ardaitheoir caidéil, raon sreafa úsáide, chun cosc ​​a chur ar shreabhadh íseal nó fórsa caidéalaithe ard-ardaitheoir, an t-imthaca sá agus páirteanna eile den chaitheamh, an ró-ualach mótair dóite

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100MΩ, after the start to observe the voltage and current, check the motor winding insulation, whether it meets the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature motor

The pump parts of this product are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The product adopts water immersion wet three-phase asynchronous motor, the motor cavity is full of clean water, used to cool the motor and lubricate the bearing. The pressure regulating diaphragm set at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the water inside the body caused by the temperature rise of the motor. In order to prevent the sand particles from entering the motor, the upper end of the motor shaft extension is installed with two oil seals, and the sand ring is set to form a sand blocking structure. At the same time, in order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft through the coupling, and the bottom of the motor is equipped with a thrust bearing. The motor and pump bearing are lubricated by water. The stator winding of the motor adopts high quality submersible motor winding with high insulation performance. The pump design adopts computer CAD, with simple structure and good technical performance.

(1) Ullmhúchán roimh shuiteáil:
1. Seiceáil an gcomhlíonann an caidéal báite na coinníollacha úsáide agus an raon feidhme a shonraítear sa lámhleabhar.
2. Ag baint úsáide as obiect trom le trastomhas comhionann le trastomhas seachtrach uasta an chaidéil báite, tomhais an féidir le trastomhas inneldiameter an tobair an caidéal báite a fheistiú, agus tomhas an gcomhlíonann doimhneacht an tobair na ceanglais suiteála.
3. Seiceáil an bhfuil tolladh an tobair glan agus an bhfuil uisce an tobair suaite. Ná húsáid caidéal leictreach intumtha riamh chun láib agus gaineamh an chaidéil welor a ní chun damáiste roimh am a sheachaint don chaidéal leictreach intumtha.
4. Seiceáil an bhfuil suíomh an clamp suiteála welhead oiriúnach agus an féidir leis cáilíocht an aonaid iomláin a sheasamh
5. Seiceáil an bhfuil na comhpháirteanna caidéil báite críochnaithe agus suiteáilte i gceart de réir an léaráid tionóil sa lámhleabhar Bain an scáileán scagaire agus rothlaigh an cúpláil féachaint an rothlaíonn sé go solúbtha
6. Díscriú an scriú uisce agus líon an cuas mótair le huisce glan, neamhchreimneach (tabhair faoi deara. Bí cinnte é a chomhdú), ansin déan an scriú uisce níos doichte. Tar éis 12 uair an chloig d'instealladh uisce, níor chóir go mbeadh friotaíocht inslithe an mhótair níos lú ná 150M Q nuair a thomhaistear é le tábla croith 500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Is é seo a leanas an léaráid próiseas sreangú cábla ceangailte:

8. Bain úsáid as multimeter chun a sheiceáil an bhfuil na sreanga trí chéim ceangailte agus an bhfuil an fhriotaíocht DC cothromaithe thart.
9. Seiceáil an bhfuil an ciorcad agus an cumas claochladáin ró-ualach, agus ansin an lasc cosanta ró-ualach nó an trealamh tosaigh a nascadh. Féach Tábla 2 le haghaidh samhlacha sonracha, agus ansin Doirt buicéad uisce isteach sa chaidéal uisce ón asraon caidéil uisce chun na imthacaí rubair a lubricadh sa chaidéal, agus ansin cuir an caidéal leictreach intumtha ina seasamh agus go seasta.Start (gan níos mó ná soicind amháin) agus seiceáil an bhfuil an treo stiúrtha comhsheasmhach leis an gcomhartha stiúrtha. Mura bhfuil, babhtáil aon dá chónaisc den chábla trí phas. Ansin shuiteáil an scagaire agus ullmhaigh tú chun dul síos ar an tobar. Má úsáidtear é in ócáidí speisialta (cosúil le díoga, díoga, aibhneacha, locháin, locháin, etc.), ní mór an caidéal leictreach a thalamh go hiontaofa.

(2) Trealamh agus uirlisí suiteála:
1. Péire amháin de slabhraí ardaithe ar feadh níos mó ná dhá tonna.
2. Tripod le airde ingearach nach lú ná ceithre mhéadar.
3. Dhá rópa crochta (rópaí sreang) ar féidir leo meáchan níos mó ná tonna amháin a iompróidh (is féidir meáchan sraith iomlán caidéil uisce a iompróidh).
4. Suiteáil dhá phéire teanntáin (splints).
5. Wrenches, casúir, scriúirí, uirlisí leictreacha agus ionstraimí, etc.

(3) Suiteáil caidéil leictreacha:
1. Taispeántar léaráid suiteála an chaidéil leictreacha intumtha i bhFíor 2. Taispeántar na toisí suiteála sonracha i dTábla 3 "Liosta Toisí Suiteála an Chaidéil Leictreach Intumtha".

2. Is féidir caidéil leictreacha báite le ceann níos lú ná 30 méadar a ardú go díreach isteach sa tobar ag baint úsáide as píobáin agus rópaí sreang nó rópaí cnáib eile ar féidir leo meáchan iomlán an mheaisín iomláin, píopaí uisce, agus uisce sna píopaí a iompar.

3. Úsáideann caidéil le ceann níos mó ná 30 méadar píopaí cruach, agus is é seo a leanas an t-ord suiteála:
① Bain úsáid as clamp chun ceann uachtarach an chaidéil uisce a chlampáil (tá an mótar agus an caidéal uisce ceangailte ag an am seo), ardaigh sé le slabhra crochta, agus ceangail go mall isteach sa tobar é go dtí go gcuirfidh tú an clamp ar cheann an tobair agus bain an slabhra crochta.
② Bain úsáid as péire teanntáin eile chun píopa a chlampáil, é a ardú le slabhra crochta 15 cm ar shiúl ón flange, agus é a ísliú go mall. Idir flange píopa agus flange caidéil Cuir an ceap rubair in áit agus déan an píopa agus an caidéal a dhéanamh níos doichte go cothrom le boltaí, cnónna agus leicneáin earraigh.
③ Ardaigh an caidéal báite beagán, bain an clamp ar thaobh uachtarach an chaidéil uisce, ceangail an cábla go daingean leis an bpíobán uisce le téip plaisteach, agus é a cheangal go mall síos go dtí go gcuirtear an clamp ag ceann an tobair.
④ Bain úsáid as an modh céanna chun na píopaí uisce go léir a cheangal isteach sa tobar.
⑤ Tar éis an cábla luaidhe-amach a bheith ceangailte leis an lasc rialaithe, tá sé ceangailte leis an soláthar cumhachta trí phas.

(4) Rudaí le tabhairt faoi deara le linn na suiteála:
1. Má aimsítear feiniméan jamming le linn an phróisis caidéalaithe, cas nó tarraing an píopa uisce chun an pointe jamming a shárú. Mura n-oibríonn bearta éagsúla fós, le do thoil Ná cuir an caidéal síos chun damáiste a sheachaint don chaidéal leictreach intumtha agus don tobar.
2. Le linn na suiteála, ba chóir eochaircheap rubair a chur ar flange gach píopa agus é a cheangal go cothrom.
3. Nuair a íslítear an caidéal uisce isteach sa tobar, ba chóir é a chur i lár an phíobáin tobair chun an caidéal a chosc ó bheith ag rith i gcoinne bhalla an tobair ar feadh i bhfad, rud a fhágann go mbeidh an caidéal ag creathadh agus an mótar a scuabadh agus a dhó. .
4. Déan doimhneacht an chaidéil uisce go bun an tobair a chinneadh de réir coinníollacha sreafa gaineamh agus siolta an tobair. Ná cuir an caidéal sa láib. De ghnáth ní lú ná 3 mhéadar an fad ón gcaidéal uisce go bun an tobair (féach Fíor 2).
5. Níor cheart go mbeadh doimhneacht iontrála uisce an chaidéil uisce níos lú ná 1-1.5 méadar ón leibhéal uisce dinimiciúil go dtí an nód inlet uisce (féach Fíor 2). Seachas sin, féadfar damáiste a dhéanamh go héasca ar imthacaí an chaidéil uisce.
6. Ní féidir le hardaitheoir an chaidéil uisce a bheith ró-íseal. Seachas sin, is gá comhla geata a shuiteáil ar phíblíne uisce an tobair chun sreabhadh an chaidéil ag an bpointe sreafa rátáilte a rialú chun an mótar a chosc ó ró-ualach agus a dhó mar gheall ar rátaí sreafa móra.
7. Nuair a bhíonn an caidéal uisce ag rith, ba cheart go mbeadh an t-aschur uisce leanúnach agus fiú, ba cheart go mbeadh an sruth cobhsaí (faoi choinníollacha oibre rátáilte, go ginearálta gan níos mó ná 10% den sruth rátáilte), agus níor cheart go mbeadh aon chreathadh nó torann ann. Má tá aon neamhghnáchaíocht ann, ba chóir an meaisín a stopadh chun an chúis a fháil amach agus é a dhíchur.
8. Nuair a shuiteáil tú, tabhair aird ar shocrú na sreinge talún mótair (féach Fíor 2). Nuair is píopa cruach é an píopa uisce, déan é a threorú as clamp an tobair; nuair is píopa plaisteach an píopa uisce, é a threorú ó mharc talún an chaidéil leictreach.

5. 1 submersible pump installation is complete, re-check the insulation resistance and three-phase conduction from the switch, check the instrument and start the equipment connection error, if there is no problem, can start the trial, after the start of the instrument indicating readings whether more than the nameplate stipulated rated voltage and current, observe the pump noise and vibration phenomenon, everything is normal can be put into operation.
6. Ba chóir 2 oibríocht caidéil don chéad cheithre huaire, a stoptar síos go tapa tástáil ar an friotaíocht inslithe theirmigh an mótair, níor chóir an luach a bheith níos lú ná 0.5 megaohm.
7. 3 pump shutdown, should be started after an interval of five minutes, to prevent the water column in the pipe has not completely reflux caused by excessive motor current and burnout.
8. 4 caidéil i ngnáthoibriú, d'fhonn a shíneadh a shaol seirbhíse, a sheiceáil leis an voltas soláthair, ag obair atá ann faoi láthair agus friotaíocht inslithe gnáth, má aimsítear an staid seo a leanas, ba chóir stop a chur láithreach fabhtcheartaithe.
9.  
10. 1 sa riocht rátáilte, tá an reatha níos mó ná 20%.
11. 2 leibhéal uisce dinimiciúil go dtí an t-alt inlet uisce, is cúis le huisce uaineach.
12. 3 caidéil báite creathadh trom nó torann.
13. Tá 4 voltas soláthair níos ísle ná 340 volta.
14. 5 vacuum dóite amach céim.
15. 6 damáiste píopa uisce.
16. Tá 7 mótair chun an fhriotaíocht inslithe theirmigh níos lú ná 0.5 megaohm.
17.  
18. 5. This product is a high-quality submersible pump, in addition to the efficient pumping function, but also easy to maintain and clean. The disassembly process is simple and clear, just follow the steps to untie the cable, remove the pipeline part, take off the line protection plate, loosen the water discharge bolt, remove the filter and loosen the fixing screw, separate the pump and the motor, and then remove the parts of the pump and the motor, pay attention to avoid damage. When assembling, thoroughly clean the components, apply sealant on the mating surface and fasteners, and then assemble in the opposite order. Every year or two years after immersion, check in accordance with the steps, replace the worn parts. This product has a reasonable structure, easy to operate, and is suitable for various occasions for pump needs.

 1, cuir an t-uisce amach sa chuas mótair (go háirithe sa gheimhreadh chun an mótar a chosc ó reo), agus an cábla a cheangal go maith.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 3, ba chóir go fadtéarmach aird a thabhairt ar chosc meirge na caidéil báite.

01 Iontógáil uisce domhain tobair

02 Soláthar uisce ard-ardú

03 soláthar uisce sléibhe 

04 túr uisce

05 Uisciúcháin talmhaíochta

06 uisciúcháin gairdín

07 iontógáil uisce abhann

08 uisce tí