Caidéal Intumtha Deep Well 125QJR

Suitable for underground hot water mining with water temperature below 100°C, with heat resistance, corrosion resistance, aging resistance and other characteristics

This product is a powerful three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%) electric pump, suitable for all kinds of occasions need high-power pump. Its design considers a variety of water quality factors, including water temperature not higher than 20 °C, solid impurities content is not greater than 0.01%, PH value is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L, etc. The product adopts a closed or water immersion wet structure of the motor, before use in the submersible motor chamber filled with clean water to prevent empty fill. Requirements in strict accordance with the requirements of the matching cable and equipped with external overload protection device. To ensure stable operation, the submersible pump must be completely immersed in water operation, the insertion depth shall not exceed 70 meters, and the distance from the bottom of the well shall not be less than 3 meters. In addition, the pump shall not be a no-load test before start. In general, this product has the characteristics of high efficiency and stability, suitable for a variety of pump tasks in harsh environment.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, strictly according to the provisions of the pump lift, flow range of use, to prevent low flow or high lift pumping force, the thrust bearing and other parts of the wear, the motor overload burned 6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the water in the motor cavity, prevent the motor cavity water ice damage caused by low temperature.

The pump parts are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The motor is a water-filled submersible three-phase asynchronous motor, which is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the difference in internal water expansion and contraction pressure caused by the temperature rise of the motor. In order to prevent the sand in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft through a coupling, and a thrust bearing is installed at the lower part of the motor. The lubrication of the motor and the pump bearing is water lubrication. The stator winding of the motor adopts high quality submersible motor winding wire, with high insulation performance. The pump adopts computer CAD design, with simple structure and excellent technical performance.

(1) Ullmhúchán roimh shuiteáil:
1. Seiceáil an gcomhlíonann an caidéal báite na coinníollacha úsáide agus an raon feidhme a shonraítear sa lámhleabhar.
2. Ag baint úsáide as obiect trom le trastomhas comhionann le trastomhas seachtrach uasta an chaidéil báite, tomhais an féidir le trastomhas inneldiameter an tobair an caidéal báite a fheistiú, agus tomhas an gcomhlíonann doimhneacht an tobair na ceanglais suiteála.
3. Seiceáil an bhfuil tolladh an tobair glan agus an bhfuil uisce an tobair suaite. Ná húsáid caidéal leictreach intumtha riamh chun láib agus gaineamh an chaidéil welor a ní chun damáiste roimh am a sheachaint don chaidéal leictreach intumtha.
4. Seiceáil an bhfuil suíomh an clamp suiteála welhead oiriúnach agus an féidir leis cáilíocht an aonaid iomláin a sheasamh
5. Seiceáil an bhfuil na comhpháirteanna caidéil báite críochnaithe agus suiteáilte i gceart de réir an léaráid tionóil sa lámhleabhar Bain an scáileán scagaire agus rothlaigh an cúpláil féachaint an rothlaíonn sé go solúbtha
6. Díscriú an scriú uisce agus líon an cuas mótair le huisce glan, neamhchreimneach (tabhair faoi deara. Bí cinnte é a chomhdú), ansin déan an scriú uisce níos doichte. Tar éis 12 uair an chloig d'instealladh uisce, níor chóir go mbeadh friotaíocht inslithe an mhótair níos lú ná 150M Q nuair a thomhaistear é le tábla croith 500V.
7. Comhpháirteach cábla, gearrtha as muinchille rubair 120mm ó thaobh amháin den chábla atá ag dul as oifig agus an cábla meaitseála le scian leictreoir ansin tuislithe fad na trí chroí-shreanga i gcruth céimnithe, craiceann croí copair 20mm, scrape an ocsaíd. ciseal ar an taobh amuigh den sreang copair le scian nó éadach gaineamh, agus cuir isteach an dá foircinn sreang ceangailte i palirs.Tar éis ceangail an ciseal go docht le sreang copar fíneáil, sádráil sé go maith agus go daingean, agus gaineamh ar bith. burrs ar an dromchla. Ansin, ar aghaidh chuig na trí alt, bain úsáid as téip inslithe polaistiréire chun iad a chuimilt go leathchruach ar feadh trí lasca. Fillte an dá cheann den chiseal fillte go docht le snáithe nyion, agus ansin úsáid modh leathchruachta chun an téip a chuimilt ar feadh trí shraith. Wrap an outellayer le ard-bhrú téip inslithe ar feadh trí shraith. Ar deireadh, fillte na trí shnáithe le chéile agus fillte arís agus arís eile ar feadh cúig sraitheanna le téip ardbhrú. Ní mór gach ciseal a bheith ceangailte go docht, agus ní mór na hailt interlayer a bheith daingean agus fimm chun uisce a chosc ó treá agus damáiste a dhéanamh don insliú, Tar éis timfhilleadh, soak in uisce ag teocht an tseomra de 20 'c ar feadh 12 uair an chloig, agus friotaíocht inslithe a thomhas le tábla chroitheadh. , nár chóir a bheith níos lú ná 100M Ω

Is é seo a leanas an léaráid próiseas sreangú cábla ceangailte:

8. Bain úsáid as multimeter chun a sheiceáil an bhfuil na sreanga trí chéim ceangailte agus an bhfuil an fhriotaíocht DC cothromaithe thart.
9. Seiceáil an bhfuil an ciorcad agus an cumas claochladáin ró-ualach, agus ansin an lasc cosanta ró-ualach nó an trealamh tosaigh a nascadh. Féach Tábla 2 le haghaidh samhlacha sonracha, agus ansin Doirt buicéad uisce isteach sa chaidéal uisce ón asraon caidéil uisce chun na imthacaí rubair a lubricadh sa chaidéal, agus ansin cuir an caidéal leictreach intumtha ina seasamh agus go seasta.Start (gan níos mó ná soicind amháin) agus seiceáil an bhfuil an treo stiúrtha comhsheasmhach leis an gcomhartha stiúrtha. Mura bhfuil, babhtáil aon dá chónaisc den chábla trí phas. Ansin shuiteáil an scagaire agus ullmhaigh tú chun dul síos ar an tobar. Má úsáidtear é in ócáidí speisialta (cosúil le díoga, díoga, aibhneacha, locháin, locháin, etc.), ní mór an caidéal leictreach a thalamh go hiontaofa.

(2) Trealamh agus uirlisí suiteála:
1. Péire amháin de slabhraí ardaithe ar feadh níos mó ná dhá tonna.
2. Tripod le airde ingearach nach lú ná ceithre mhéadar.
3. Dhá rópa crochta (rópaí sreang) ar féidir leo meáchan níos mó ná tonna amháin a iompróidh (is féidir meáchan sraith iomlán caidéil uisce a iompróidh).
4. Suiteáil dhá phéire teanntáin (splints).
5. Wrenches, casúir, scriúirí, uirlisí leictreacha agus ionstraimí, etc.

(3) Suiteáil caidéil leictreacha:
1. Taispeántar léaráid suiteála an chaidéil leictreacha intumtha i bhFíor 2. Taispeántar na toisí suiteála sonracha i dTábla 3 "Liosta Toisí Suiteála an Chaidéil Leictreach Intumtha".

2. Is féidir caidéil leictreacha báite le ceann níos lú ná 30 méadar a ardú go díreach isteach sa tobar ag baint úsáide as píobáin agus rópaí sreang nó rópaí cnáib eile ar féidir leo meáchan iomlán an mheaisín iomláin, píopaí uisce, agus uisce sna píopaí a iompar.

3. Úsáideann caidéil le ceann níos mó ná 30 méadar píopaí cruach, agus is é seo a leanas an t-ord suiteála:
① Bain úsáid as clamp chun ceann uachtarach an chaidéil uisce a chlampáil (tá an mótar agus an caidéal uisce ceangailte ag an am seo), ardaigh sé le slabhra crochta, agus ceangail go mall isteach sa tobar é go dtí go gcuirfidh tú an clamp ar cheann an tobair agus bain an slabhra crochta.
② Bain úsáid as péire teanntáin eile chun píopa a chlampáil, é a ardú le slabhra crochta 15 cm ar shiúl ón flange, agus é a ísliú go mall. Idir flange píopa agus flange caidéil Cuir an ceap rubair in áit agus déan an píopa agus an caidéal a dhéanamh níos doichte go cothrom le boltaí, cnónna agus leicneáin earraigh.
③ Ardaigh an caidéal báite beagán, bain an clamp ar thaobh uachtarach an chaidéil uisce, ceangail an cábla go daingean leis an bpíobán uisce le téip plaisteach, agus é a cheangal go mall síos go dtí go gcuirtear an clamp ag ceann an tobair.
④ Bain úsáid as an modh céanna chun na píopaí uisce go léir a cheangal isteach sa tobar.
⑤ Tar éis an cábla luaidhe-amach a bheith ceangailte leis an lasc rialaithe, tá sé ceangailte leis an soláthar cumhachta trí phas.

(4) Rudaí le tabhairt faoi deara le linn na suiteála:
1. Má aimsítear feiniméan jamming le linn an phróisis caidéalaithe, cas nó tarraing an píopa uisce chun an pointe jamming a shárú. Mura n-oibríonn bearta éagsúla fós, le do thoil Ná cuir an caidéal síos chun damáiste a sheachaint don chaidéal leictreach intumtha agus don tobar.
2. Le linn na suiteála, ba chóir eochaircheap rubair a chur ar flange gach píopa agus é a cheangal go cothrom.
3. Nuair a íslítear an caidéal uisce isteach sa tobar, ba chóir é a chur i lár an phíobáin tobair chun an caidéal a chosc ó bheith ag rith i gcoinne bhalla an tobair ar feadh i bhfad, rud a fhágann go mbeidh an caidéal ag creathadh agus an mótar a scuabadh agus a dhó. .
4. Déan doimhneacht an chaidéil uisce go bun an tobair a chinneadh de réir coinníollacha sreafa gaineamh agus siolta an tobair. Ná cuir an caidéal sa láib. De ghnáth ní lú ná 3 mhéadar an fad ón gcaidéal uisce go bun an tobair (féach Fíor 2).
5. Níor cheart go mbeadh doimhneacht iontrála uisce an chaidéil uisce níos lú ná 1-1.5 méadar ón leibhéal uisce dinimiciúil go dtí an nód inlet uisce (féach Fíor 2). Seachas sin, féadfar damáiste a dhéanamh go héasca ar imthacaí an chaidéil uisce.
6. Ní féidir le hardaitheoir an chaidéil uisce a bheith ró-íseal. Seachas sin, is gá comhla geata a shuiteáil ar phíblíne uisce an tobair chun sreabhadh an chaidéil ag an bpointe sreafa rátáilte a rialú chun an mótar a chosc ó ró-ualach agus a dhó mar gheall ar rátaí sreafa móra.
7. Nuair a bhíonn an caidéal uisce ag rith, ba cheart go mbeadh an t-aschur uisce leanúnach agus fiú, ba cheart go mbeadh an sruth cobhsaí (faoi choinníollacha oibre rátáilte, go ginearálta gan níos mó ná 10% den sruth rátáilte), agus níor cheart go mbeadh aon chreathadh nó torann ann. Má tá aon neamhghnáchaíocht ann, ba chóir an meaisín a stopadh chun an chúis a fháil amach agus é a dhíchur.
8. Nuair a shuiteáil tú, tabhair aird ar shocrú na sreinge talún mótair (féach Fíor 2). Nuair is píopa cruach é an píopa uisce, déan é a threorú as clamp an tobair; nuair is píopa plaisteach an píopa uisce, é a threorú ó mharc talún an chaidéil leictreach.

• （1）With the continuous development of modern technology, submersible pumps play a crucial role in the field of pumps. After installing the submersible pump, check the insulation resistance and three-phase continuity repeatedly to ensure that there are no errors in the connection between the instrument and the starting equipment. If everything is normal, the test equipment can be started. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, pay attention to observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. After the pump runs for four hours for the first time, it should be closed and the thermal insulation resistance of the motor should be tested quickly, and its value should not be less than 0.5 megaohms. After stopping the pump, restart it after five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to overcurrent. After the pump is running normally, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the equipment should be shut down immediately to troubleshoot. The current exceeds 20% under the rated working conditions; the dynamic water level drops to the inlet section, resulting in intermittent drainage; the submersible pump vibrates violently or makes noisy sounds; the supply voltage is lower than 340 volts; any fuse is broken; the water pipe is damaged; The thermal insulation resistance between the motor and the ground is less than 0.5 megaohm.These recommended operating procedures and safety measures ensure the safe operation of the submersible pump, prolong the service life of the equipment, and provide users with a reliable pump choice.
•  
• （2）Unit disassembly:
• 1 untie the cable tie, remove the pipeline part, remove the wire plate.
• 2 unscrew the water release bolt, put the water in the motor chamber.
• 3 remove the filter, loose the fixing screw of the motor shaft on the coupling.
• 4 unscrew the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5 the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending the pump shaft and various bumps in the disassembly process.
• 6 the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nut, base, shaft head lock nut, thrust plate, key, lower guide bearing seat, double head bolt from the bottom of the motor in turn. Then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7 unit assembly: Before assembly, the rust and dirt of the parts should be cleaned, and the mating surfaces and fasteners should be coated with sealant. Then they should be assembled in the reverse order of disassembly (the up and down momentum of the motor shaft is about 1 mm after assembly). After assembly, the coupling should be flexible, and then the filter screen test machine.
•  
• （3）The submersible pump should be dismantled and repaired according to Article 5 for each operation year, or less than one year, but the submersible time has reached two years, and the worn parts should be replaced.

 1, cuir an t-uisce amach sa chuas mótair (go háirithe sa gheimhreadh chun an mótar a chosc ó reo), agus an cábla a cheangal go maith.

 2, stóráil i seomra faoi dhíon gan substaintí agus gáis creimneach, ag teocht faoi bhun 40 ° C.

 3, ba chóir go fadtéarmach aird a thabhairt ar chosc meirge na caidéil báite.

01 Iontógáil uisce domhain tobair

02 Soláthar uisce ard-ardú

03 soláthar uisce sléibhe 

04 túr uisce

05 Uisciúcháin talmhaíochta

06 uisciúcháin gairdín

07 iontógáil uisce abhann

08 uisce tí