125QJB Deep Well Submersible Pump

Frequency conversion winding design, ensure the motor in 1HZ-50HZ long-term stable conversion operation. Energy saving, longer service life.

1, soláthar cumhachta: trí chéim AC 380V (caoinfhulaingt + / - 5%), 50HZ (caoinfhulaingt + / - 1%).

2, cáilíocht uisce:

(1) nach bhfuil teocht an uisce níos airde ná 20 ° C;

(2) nach bhfuil ábhar soladach eisíontais (cóimheas mais) níos mó ná 0.01%;

(3) luach PH (pH) 6.5-8.5;

(4) nach mó an cion suilfíd hidrigine ná 1.5mg/L;

(5) nach bhfuil cion ian clóiríd níos mó ná 400mg/L.

3, tá an mótar dúnta nó uisce-líonadh struchtúr fliuch, roimh úsáid ní mór an cuas mótair báite a bheith iomlán d'uisce glan, chun cosc ​​a chur iomlán bréagach, agus ansin níos doichte an t-instealladh uisce, boltaí scaoileadh aeir, ní cheadaítear a úsáid ar shlí eile.

4, ní mór caidéil báite a bheith go hiomlán báite san uisce, nach bhfuil an doimhneacht tumadóireacht níos mó ná 70m, nach bhfuil an bun an caidéil báite ó bun an tobair níos lú ná 3m.

5, ba cheart go mbeadh an sreabhadh uisce tobair in ann an t-aschur uisce caidéil báite a chomhlíonadh agus oibriú leanúnach, ba cheart an t-aschur uisce caidéil báite a rialú ag 0.7 - 1.2 uair an sreabhadh rátáilte.

6, ba chóir go mbeadh an tobar díreach, ní féidir an caidéal báite a úsáid nó a dhumpáil, ach úsáid ingearach.

7, ní mór an caidéal báite a mheaitseáil leis an gcábla de réir na gceanglas, agus an gléas cosanta ró-ualach seachtrach. 8, tá cosc ​​dian ar an gcaidéal gan meaisín tástála aon-ualach uisce

 The well submersible pump is a pump suitable for clear water. It is strictly prohibited to dig new wells and pump out mud and sand. The voltage grade of the well pump is 380V/50HZ, and other voltage grades of the submersible motor need to be customized. Underground cables must be waterproof cables and must be equipped with starting equipment, such as distribution box, etc. The starting equipment should have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and idling protection, etc. In abnormal cases, the protective device should be tripped in time. When installing and using the pump, it must be firmly grounded. It is prohibited to push and pull the switch when the hands and feet are wet. The power supply must be cut off before installing and maintaining the pump. An obvious "anti-electric shock" sign must be set up where the pump is used. Before going down the well or installing the motor, the inner cavity must be filled with distilled water or non-corrosive clean cold water, and the water injection/drainage bolts must be tightened. Fill the pump with water for ground test to lubricate the rubber bearings. The instant start time shall not exceed one second to check whether the direction is correct and consistent with the direction indication. Be sure to pay attention to safety when placing the pump upright to prevent overturning and causing injury. Strictly in accordance with the provisions of the pump lift and flow range of use, to prevent the pump flow at low lift or excessive pull at high lift, resulting in extreme wear of thrust bearings and other components, resulting in motor overload burn. After the pump into the well, the insulation resistance between the motor and the ground shall be measured, which shall not be less than 100MΩ. After the start, observe the voltage and current regularly, and check the motor winding insulation, to see if it meets the requirements; if the pump storage temperature is below the freezing point, the water in the motor cavity should be discharged, so as to avoid the water in the motor cavity freezing and damaging the motor due to low temperature.

The pump part is mainly composed of pump shaft,impeller,diversion shell,rubber bearing,check valve body(optional)and other components.The motor part is mainly composed of base,pressure regulating diaphragm,thrust bearing,thrust plate,lower guide bearing seat,stator,rotor,upper guide bearing seat,sand ring,water inlet section,lead cable and other components.

Áirítear ar phríomhghnéithe an táirge:

1.The motor is a water-loaded wet submersible three-phase asynchronous motor,and the motor cavity is filled with clean water for cooling the motor and lubricating the bearing.The regulating diaphragm at the bottom of the motor is used to adjust the expansion and contraction pressure difference inside and outside the body caused by the temperature rise of the motor.
2.In order to prevent the sand particles in the well water from entering the motor,two oil seals are installed at the extension end of the motor shaft,and the sand ring is installed to form a sand prevention structure.
3.In order to prevent the pump shaft from jumping when starting,the pump shaft is connected with the motor shaft through a coupling,and the thrust bearing is installed at the bottom of the motor.
4.The lubrication of the motor and the pump bearing is water lubrication.
5.The stator winding of the motor adopts high-quality submersible motor winding wire,with excellent insulation performance.
6.The pump is designed by computer CAD,with simple structure and excellent technical performance.

(1) Ullmhúchán roimh shuiteáil:
1. Seiceáil an gcomhlíonann an caidéal báite na coinníollacha úsáide agus an raon feidhme a shonraítear sa lámhleabhar.
2. Ag baint úsáide as obiect trom le trastomhas comhionann le trastomhas seachtrach uasta an chaidéil báite, tomhais an féidir le trastomhas inneldiameter an tobair an caidéal báite a fheistiú, agus tomhas an gcomhlíonann doimhneacht an tobair na ceanglais suiteála.

3. Seiceáil an bhfuil tolladh an tobair glan agus an bhfuil uisce an tobair suaite. Ná húsáid caidéal leictreach intumtha riamh chun láib agus gaineamh an chaidéil welor a ní chun damáiste roimh am a sheachaint don chaidéal leictreach intumtha.

4. Seiceáil an bhfuil suíomh an clamp suiteála welhead oiriúnach agus an féidir leis cáilíocht an aonaid iomláin a sheasamh

5. Seiceáil an bhfuil na comhpháirteanna caidéil báite críochnaithe agus suiteáilte i gceart de réir an léaráid tionóil sa lámhleabhar Bain an scáileán scagaire agus rothlaigh an cúpláil féachaint an rothlaíonn sé go solúbtha

6. Díscriú an scriú uisce agus líon an cuas mótair le huisce glan, neamhchreimneach (tabhair faoi deara. Bí cinnte é a chomhdú), ansin déan an scriú uisce níos doichte. Tar éis 12 uair an chloig d'instealladh uisce, níor chóir go mbeadh friotaíocht inslithe an mhótair níos lú ná 150M Q nuair a thomhaistear é le tábla croith 500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.

After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Is é seo a leanas an léaráid próiseas sreangú cábla ceangailte:

8. Bain úsáid as multimeter chun a sheiceáil an bhfuil na sreanga trí chéim ceangailte agus an bhfuil an fhriotaíocht DC cothromaithe thart.
9. Check whether the circuit and transformer capacity are overloaded, and then connect the overload protection switch or starting equipment. See Table 2 for specific models, and then
Pour a bucket of water into the water pump from the water pump outlet to lubricate the rubber bearings in the pump, and then place the submersible electric pump upright and steady.
Start (no more than one second) and check whether the steering direction is consistent with the steering sign. If not, swap any two connectors of the three-phase cable.
Then install the filter and prepare to go down the well. If used in special occasions (such as ditches, ditches, rivers, ponds, ponds, etc.), the electric pump must be reliably grounded.

(2) Trealamh agus uirlisí suiteála:
1. Péire amháin de slabhraí ardaithe ar feadh níos mó ná dhá tonna.
2. Tripod le airde ingearach nach lú ná ceithre mhéadar.
3. Dhá rópa crochta (rópaí sreang) ar féidir leo meáchan níos mó ná tonna amháin a iompróidh (is féidir meáchan sraith iomlán caidéil uisce a iompróidh).
4. Suiteáil dhá phéire teanntáin (splints).
5. Wrenches, casúir, scriúirí, uirlisí leictreacha agus ionstraimí, etc.

(3) Suiteáil caidéil leictreacha:
1. Taispeántar léaráid suiteála an chaidéil leictreacha intumtha i bhFíor 2. Taispeántar na toisí suiteála sonracha i dTábla 3 "Liosta Toisí Suiteála an Chaidéil Leictreach Intumtha".

2. Is féidir caidéil leictreacha báite le ceann níos lú ná 30 méadar a ardú go díreach isteach sa tobar ag baint úsáide as píobáin agus rópaí sreang nó rópaí cnáib eile ar féidir leo meáchan iomlán an mheaisín iomláin, píopaí uisce, agus uisce sna píopaí a iompar.

3. Úsáideann caidéil le ceann níos mó ná 30 méadar píopaí cruach, agus is é seo a leanas an t-ord suiteála:
①Use a clamp to clamp the upper end of the water pump part (the motor and water pump have been connected at this time), lift it with a hanging chain, and slowly tie it into the well until
Put the clamp on the wellhead and remove the hanging chain.
② Use another pair of clamps to clamp a pipe, lift it with a hanging chain 15 cm away from the flange, and lower it slowly. Between pipe flange and pump flange
Put the rubber pad in place and tighten the pipe and pump evenly with bolts, nuts and spring washers.
③ Ardaigh an caidéal báite beagán, bain an clamp ar thaobh uachtarach an chaidéil uisce, ceangail an cábla go daingean leis an bpíobán uisce le téip plaisteach, agus é a cheangal go mall síos go dtí go gcuirtear an clamp ag ceann an tobair.
④ Bain úsáid as an modh céanna chun na píopaí uisce go léir a cheangal isteach sa tobar.
⑤ Tar éis an cábla luaidhe-amach a bheith ceangailte leis an lasc rialaithe, tá sé ceangailte leis an soláthar cumhachta trí phas.

(4) Rudaí le tabhairt faoi deara le linn na suiteála:
1. If a jamming phenomenon is found during the pumping process, turn or pull the water pipe to overcome the jamming point. If various measures still do not work, please
Do not force the pump down to avoid damage to the submersible electric pump and the well.
2. Le linn na suiteála, ba chóir eochaircheap rubair a chur ar flange gach píopa agus é a cheangal go cothrom.
3. Nuair a íslítear an caidéal uisce isteach sa tobar, ba chóir é a chur i lár an phíobáin tobair chun an caidéal a chosc ó bheith ag rith i gcoinne bhalla an tobair ar feadh i bhfad, rud a fhágann go mbeidh an caidéal ag creathadh agus an mótar a scuabadh agus a dhó. .
4. Déan doimhneacht an chaidéil uisce go bun an tobair a chinneadh de réir coinníollacha sreafa gaineamh agus siolta an tobair. Ná cuir an caidéal sa láib. De ghnáth ní lú ná 3 mhéadar an fad ón gcaidéal uisce go bun an tobair (féach Fíor 2).
5. Níor cheart go mbeadh doimhneacht iontrála uisce an chaidéil uisce níos lú ná 1-1.5 méadar ón leibhéal uisce dinimiciúil go dtí an nód inlet uisce (féach Fíor 2). Seachas sin, féadfar damáiste a dhéanamh go héasca ar imthacaí an chaidéil uisce.
6. Ní féidir le hardaitheoir an chaidéil uisce a bheith ró-íseal. Seachas sin, is gá comhla geata a shuiteáil ar phíblíne uisce an tobair chun sreabhadh an chaidéil ag an bpointe sreafa rátáilte a rialú chun an mótar a chosc ó ró-ualach agus a dhó mar gheall ar rátaí sreafa móra.
7. Nuair a bhíonn an caidéal uisce ag rith, ba cheart go mbeadh an t-aschur uisce leanúnach agus fiú, ba cheart go mbeadh an sruth cobhsaí (faoi choinníollacha oibre rátáilte, go ginearálta gan níos mó ná 10% den sruth rátáilte), agus níor cheart go mbeadh aon chreathadh nó torann ann. Má tá aon neamhghnáchaíocht ann, ba chóir an meaisín a stopadh chun an chúis a fháil amach agus é a dhíchur.
8. Nuair a shuiteáil tú, tabhair aird ar shocrú na sreinge talún mótair (féach Fíor 2). Nuair is píopa cruach é an píopa uisce, déan é a threorú as clamp an tobair; nuair is píopa plaisteach an píopa uisce, é a threorú ó mharc talún an chaidéil leictreach.

• 1.Tar éis an caidéal báite a bheith suiteáilte, seiceáil an fhriotaíocht inslithe agus an seoladh trí chéim ón lasc arís, seiceáil an bhfuil an ionstraim agus nasc an trealaimh tosaithe mícheart, mura bhfuil aon fhadhb ann, is féidir an meaisín trialach a thosú, agus breathnaigh an bhfuil léamha táscaire na hionstraime níos mó ná an voltas rátáil agus an sruth atá sonraithe ar an ainmchlár tar éis an tús, agus breathnaigh an bhfuil feiniméan torainn agus creathadh ag an gcaidéal, agus a chur i ngníomh má tá gach rud gnáth.
• 2.Tar éis an caidéal a oibriú den chéad uair ar feadh ceithre huaire, ba chóir an mótar a dhúnadh síos chun an fhriotaíocht inslithe theirmigh a thástáil go tapa, agus níor chóir go mbeadh a luach níos lú ná 0.5 megaohm.
• 3. Tar éis an caidéal a dhúnadh, ba chóir é a thosú tar éis cúig nóiméad chun an colún uisce sa phíobán a chosc ó bheith ag athshreabhadh go hiomlán agus ag cruthú sruth mótair iomarcach agus sruthán amach.
• 4. Tar éis an caidéal a chur i ngnáthoibriú, d'fhonn a shaol seirbhíse a shíneadh, is gá a sheiceáil an bhfuil an voltas soláthair, an sruth oibre agus an fhriotaíocht inslithe gnáth go rialta. Má aimsítear na coinníollacha seo a leanas, ba cheart an caidéal a mhúchadh láithreach chun fabhtcheartú a dhéanamh.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Titeann an leibhéal uisce dinimiciúil go dtí an t-alt inlet uisce, rud a fhágann go bhfuil uisce uaineach.
• 3 Tá creathadh nó torann trom ag an gcaidéal báite.
• 4 Tá an voltas soláthair níos ísle ná 340 volta.
• 5 Tá ​​fiús dóite amach.
• 6 Déantar damáiste don phíobán soláthair uisce.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1.Untie the cable tie, remove the pipeline part, and remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product is an efficient and durable submersible electric pump, suitable for a variety of environments and applications.In order to ensure the long-term use and stable performance of the product, we suggest that users pay special attention to drying the water in the motor cavity in winter to avoid freezing; in addition, the cable is coiled and tied, and properly stored in an environment without corrosive substances and gases, with a temperature below 40 °C. If the product is not used for a long time, attention should be paid to rust prevention treatment to ensure the life cycle and performance of the product.Whether for industrial use or for home use, this submersible electric pump can provide you with reliable pump service.

1. • Impeallóir
   • Muinchille seafta
   • Muinchille seafta rubair

   •  Fáinne séalaithe

01 Iontógáil uisce domhain tobair

02 Soláthar uisce ard-ardú

03 soláthar uisce sléibhe 

04 túr uisce

05 Uisciúcháin talmhaíochta

06 uisciúcháin gairdín

07 iontógáil uisce abhann

08 uisce tí