250QJB Igwe mmiri na-ekpu mmiri nke ọma

The product adopts special waterproof wire design, which can realize long-term stable conversion operation of the motor within the frequency range of 1HZ-50HZ. The frequency conversion winding design not only makes the frequency conversion deep well pump more energy saving, but also prolongs its service life. The motor winding adopts special water-resistant conductors that are resistant to high frequency impact, pulse peak voltage impact and high temperature aging, with excellent characteristics and stability.

The product is powered by three-phase AC 380V power supply, 50HZ frequency, suitable for the environment with harsh water quality conditions. Specific requirements include water temperature below 20 °C, solid impurities content is not greater than 0.01%, PH value is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L. The product adopts closed or water immersion structure of the motor, before use to ensure that the pump is fully filled with water, no-load test run is strictly prohibited. The pump must be completely immersed in water, not more than 70m water depth, water source to meet the requirements of the pump water output and continuous operation. In addition, the well must be vertical, the pump can only be used vertically. The wiring should be supported according to the requirements, and equipped with external overload protection device. This series of requirements to ensure the efficient and stable operation of the product, suitable for all kinds of special environment of the pump demand.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, n'ụzọ doro anya dị ka ndokwa nke mgbapụta ebuli, eruba nso nke ojiji, iji gbochie ala eruba ma ọ bụ elu ebuli pumping ike, mkpali ibu na akụkụ ndị ọzọ nke eyi, moto bufee ọkụ.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The pump parts are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body and so on; the motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, cable lead, etc. The main characteristic of the product is that the motor is a water-filled wet submersible three-phase asynchronous motor, the motor cavity is filled with water, used to cool the motor and lubricate the bearing; the pressure regulating diaphragm at the bottom is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two sand sealing rings are installed on the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand prevention structure. To prevent the pump shaft from jumping when starting up, the pump shaft is connected with the motor shaft through a coupling, and the thrust bearing is installed on the lower part of the motor. The motor and pump bearing adopt water lubrication technology, and the stator winding of the motor adopts high quality submersible motor winding with high insulation performance. The pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Nkwadebe tupu echichi:
1. Lelee ma mgbapụta submersible na-ezute ọnọdụ ojiji yana oke akọwapụtara na ntuziaka.
2. Iji obiect dị arọ nke nwere dayameta hà nhata kachasị elu nke mgbapụta mmiri na-ekpuchi mmiri, tụọ ma inneldiameter nke olulu mmiri ahụ nwere ike dabara na mgbapụta mmiri, ma tụọ ma omimi nke ọma na-emezu ihe achọrọ nrụnye.
3. Lelee ma olulu mmiri ahụ ọ dị ọcha ma mmiri olulu mmiri ahụ ọ na-asọ oyi. Ejila mgbapụta ọkụ eletrik na-eme ka mmiri na-asachapụ apịtị welor na mmiri ájá ka ịzenarị mmebi nke mgbapụta ọkụ eletrik n'oge.
4. Lelee ma ọnọdụ nke welhead echichi mwekota dabara na ma ọ nwere ike iguzogide qualty nke dum unit.
5. Lelee ma ọ bụrụ na akụrụngwa mgbapụta submersible zuru ezu ma wụnye ya nke ọma dị ka eserese mgbakọ na mwepụ na akwụkwọ ntuziaka Wepụ ihuenyo nzacha ma gbanwee njikọ ahụ iji hụ ma ọ na-agbagharị na-agbanwe agbanwe.
6. Kpochapụ ihe nkedo mmiri ma jupụta oghere moto na mmiri dị ọcha, nke na-adịghị emebi emebi (dee. jide n'aka na ị ga-agbanye ya), wee mee ka mmiri sie ike. Mgbe awa 12 nke ịgbanye mmiri gasịrị, nguzogide mkpuchi nke moto ekwesịghị ịbụ ihe na-erughị 150M Q mgbe a tụrụ ya na tebụl ịma jijiji 500V.
7. Njikọ eriri USB, bepụ aka uwe roba 120mm site na otu njedebe nke eriri na-apụ apụ na eriri dabara na ya na mma eletriki wee tụọ ogologo eriri isi atọ ahụ n'ụdị steepụ, wepụ isi ọla kọpa 20mm, kpochapu oxide. oyi akwa na theside nke ọla kọpa waya na mma ma ọ bụ ájá ákwà, na fanye abụọ ejikọrọ waya agwụ na palirs.Mgbe ekekọta oyi akwa tightly na ezi ọla kọpa waya, solder ya nke ọma na ike, na ájá nke ọ bụla. burrs n'elu. Mgbe ahụ, maka nkwonkwo atọ ahụ, jiri teepu mkpuchi mkpuchi polyvester kechie ha n'ụzọ dị nkenke nke etinyere maka ọdọ mmiri atọ. Jiri eriri nyion kechie nsọtụ abụọ nke oyi akwa mkpuchi, wee jiri usoro echekwabara ọkara wee kechie teepu ahụ maka ọkwa atọ. Kechie outellayer na teepu mkpuchi mkpuchi dị elu maka ọkwa atọ. N'ikpeazụ, jikọta eriri atọ ahụ ma kechie ha ugboro ugboro maka ihe ise na teepu dị elu. A ghaghị ijikọta oyi akwa nke ọ bụla, na nkwonkwo interlayer ga-adị ike na fimm ka mmiri ghara ịbanye ma mebie ihe mkpuchi ahụ, Mgbe ị na-ekpuchi ya, gbanye n'ime mmiri na okpomọkụ nke 20 'c maka awa 12, wee tụọ nguzogide mkpuchi na tebụl na-ama jijiji. , nke ekwesịghị ịbụ ihe na-erughị 100M Ω

Eserese usoro wiring cable nke agbakwunyere bụ nke a:

8. Jiri multimeter chọpụta ma ejikọrọ wires nke atọ na ma nkwụsi ike DC ọ dị oke nhata.
9. Lelee ma ikike sekit na transformer bubigara ibu, wee jikọọ ihe ngbanwe mkpuchi ibufe ma ọ bụ akụrụngwa mmalite. Hụ Tebụl 2 maka ụdị ụdị dị iche iche, wee wụsa ịwụ mmiri n'ime mgbapụta mmiri si na mmiri mgbapụta mmiri iji mee ka mmanu rọba dị na mgbapụta ahụ, wee debe mgbapụta ọkụ eletrik nke nwere ike ime ka ọ kwụ ọtọ na kwụ ọtọ. Malite (ọ bụghị ihe karịrị otu sekọnd) ma lelee ma ntụzịaka stereị ọ dabara na akara stereị. Ọ bụrụ na ọ bụghị, gbanwee njikọ abụọ ọ bụla nke eriri ụzọ atọ. Mgbe ahụ wụnye nzacha ma kwadebe ka ị gbadaa n'olulu mmiri ahụ. Ọ bụrụ na ejiri ya n'oge pụrụ iche (dịka ọwa mmiri, ọwa mmiri, osimiri, ọdọ mmiri, ọdọ mmiri, wdg), mgbapụta ọkụ eletrik ga-agbanyerịrị nke ọma.

(2) Akụrụngwa na akụrụngwa ntinye:
1. Otu ụzọ na-ebuli agbụ maka ihe karịrị tọn abụọ.
2. A tripod nwere ogologo kwụ ọtọ na-erughị mita anọ.
3. Ụdọ abụọ kwụgidere (ụdọ waya) nke nwere ike ibu ibu ihe karịrị otu ton (nwere ike ibu ibu nke nfuli mmiri zuru ezu).
4. Wụnye ụzọ abụọ nke clamps (splints).
5. Wrenches, hammers, screwdrivers, eletriki ngwaọrụ na ngwá, wdg.

(3) Nwụnye mgbapụta ọkụ eletrik:
1. E gosipụtara eserese nrụnye nke mgbapụta ọkụ eletrik submersible na eserese 2. A na-egosipụta akụkụ ntinye kpọmkwem na Tebụl 3 "Ndepụta nke nrụnye akụkụ nke mgbapụta ọkụ eletrik".

2. Enwere ike ibunye nfuli eletriki na-ekpuchi isi na isi ihe na-erughị mita 30 ozugbo n'ime olulu mmiri site na iji ụdọ na eriri waya ma ọ bụ eriri hemp ndị ọzọ nwere ike iburu igwe zuru oke nke igwe dum, ọkpọkọ mmiri na mmiri na ọkpọkọ.

3. Nfuli nke nwere isi ihe karịrị mita 30 na-eji ọkpọkọ ígwè, na usoro ntinye bụ nke a:
① Jiri ihe nkedo iji kpoo njedebe elu nke akụkụ mgbapụta mmiri (a na-ejikọta moto na mmiri mgbapụta n'oge a), bulite ya na agbụ nke nghọta, ma jiri nwayọọ nwayọọ kechie ya n'ime olulu mmiri ruo mgbe ịtinye ihe nkedo na isi mmiri ma wepụ ya. nghọta yinye.
② Jiri ụzọ mkpị ọzọ kụchie ọkpọkọ, were yinye kwụgidere 15 cm pụọ na flange, wee wetuo ya nwayọ. N'etiti ọkpọkọ flange na mgbapụta flange Tinye ihe mgbochi rọba n'ebe ma mee ka ọkpọkọ ahụ sie ike ma gbapụta ya nke ọma na bolts, mkpụrụ na mmiri mmiri.
③ Welite obere mgbapụta submersible, wepụ ihe nkedo dị na nsọtụ elu nke mgbapụta mmiri ahụ, kechie eriri ahụ nke ọma na ọkpọkọ mmiri na teepu rọba, ma jiri nwayọọ nwayọọ kechie ya ruo mgbe etinyere mkpọ ahụ n'isi olulu mmiri.
④ Jiri otu usoro ahụ kee ọkpọkọ mmiri niile n'ime olulu mmiri.
⑤ Mgbe ejikọtara eriri na-eduga na njikwa njikwa, a na-ejikọta ya na ọkụ ọkụ nke atọ.

(4) Ihe ị ga-ahụ n'oge echichi:
1. Ọ bụrụ na achọpụtara ihe mgbagwoju anya n'oge usoro mgbapụta ahụ, tụgharịa ma ọ bụ dọrọ ọkpọkọ mmiri iji merie ebe nkwụsị. Ọ bụrụ na usoro dị iche iche ka na-arụ ọrụ, biko Amanyela mgbapụta ahụ ka ọ ghara imebi mgbapụta ọkụ eletrik na olulu mmiri.
2. N'oge echichi, a ga-etinye ihe mkpuchi rọba na flange nke ọkpọkọ ọ bụla ma mee ka ọ sie ike.
3. Mgbe a na-agbanye mmiri mmiri n'ime olulu mmiri ahụ, a ga-etinye ya n'etiti ọkpọkọ nke ọma iji gbochie mgbapụta ahụ na-agba ọsọ megide mgbidi olulu mmiri ruo ogologo oge, na-eme ka mgbapụta ahụ na-ama jijiji na moto na-ekpochapụ ma gbaa ọkụ. .
4. Kpebie omimi nke mgbapụta mmiri na ala nke olulu mmiri dịka ájá na-asọ asọ na ọnọdụ silt nke olulu mmiri ahụ. Eliela mgbapụta n'ime apịtị. Ebe dị anya site na mgbapụta mmiri na ala nke olulu mmiri n'ozuzu ọ bụghị ihe na-erughị mita 3 (lee foto 2).
5. Ihe omimi ntinye mmiri nke mgbapụta mmiri kwesịrị ịbụ ihe na-erughị 1-1.5 mita site na mmiri dị ike na ọnụ mmiri ntinye mmiri (lee foto 2). Ma ọ bụghị ya, a ga-emebi bearings mgbapụta mmiri n'ụzọ dị mfe.
6. Ebuli nke mgbapụta mmiri enweghị ike ịdị ala. Ma ọ bụghị ya, ekwesịrị itinye valvụ ọnụ ụzọ ámá na pipeline mmiri nke ọma iji chịkwaa mgbapụta mgbapụta na ebe a na-agbapụta agbapụta iji gbochie moto ahụ ka ọ ghara ibufe ma gbaa ọkụ n'ihi nnukwu ọnụọgụ mmiri.
7. Mgbe mgbapụta mmiri na-agba ọsọ, mmepụta mmiri kwesịrị ịdị na-aga n'ihu na ọbụna, nke dị ugbu a kwesịrị ịdị na-eguzosi ike (n'okpuru ọnọdụ ọrụ a kwadoro, n'ozuzu ọ dịghị ihe karịrị 10% nke akara ugbu a), na e kwesịghị inwe mkpọtụ ma ọ bụ mkpọtụ. Ọ bụrụ na enwere ihe na-adịghị mma, a ga-akwụsị igwe ahụ iji chọpụta ihe kpatara ya ma kpochapụ ya.
8. Mgbe ị na-etinye ya, ṅaa ntị na ntọala nke waya mgbanaka moto (lee foto 2). Mgbe ọkpọkọ mmiri bụ ọkpọkọ ígwè, dupụta ya site na mkpọchi olulu mmiri; mgbe ọkpọkọ mmiri bụ ọkpọkọ plastik, duga ya site na akara ala nke mgbapụta eletrik.

• 1.After the submersible pump is installed, check the insulation resistance and three-phase conduction from the switch again, check whether the instrument and the connection of the start 2.equipment are wrong, if there is no problem, the trial machine can be started, and observe whether the indicator readings of the instrument exceed the rated voltage and current specified on 3.the nameplate after the start, and observe whether the pump has noise and vibration phenomenon, and put into operation if everything is normal.
• 4.After the first operation of the pump for four hours, the motor should be shut down to test the thermal insulation resistance quickly, and its value should not be less than 0.5 megaohm.
• 5.After the pump is shut down, it should be started after five minutes to prevent the water column in the pipe from being completely reflowed and causing excessive motor current and burnout.
• 6.After the pump is put into normal operation, in order to prolong its service life, it is necessary to check whether the supply voltage, working current and insulation resistance are normal regularly. If the following conditions are found, the pump should be shut down immediately to troubleshoot.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Mmiri dị ike na-adaba na ngalaba ntinye mmiri, na-eme ka mmiri na-adịte aka.
• 3 Mgbapu nke submersible nwere oke ịma jijiji ma ọ bụ mkpọtụ.
• 4 voltaji ọkọnọ dị ala karịa 340 volts.
• 5 Igwe ọkụ na-agbanyụ ọkụ.
• 6 Igwe mmiri na-enye mmiri mebiri emebi.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1 Untie the cable tie, remove the pipeline part, and remove the wire plate. 2 screw down the water bolt, put the water in the motor chamber.
• 3 wepụ ihe nzacha, tọpụ ihe nkedo edozi na njikọ iji dozie ogwe moto.
• 4 gbadaa bolt na-ejikọta ngalaba ntinye mmiri na moto, ma kewapụ mgbapụta ahụ na moto (leba anya na ọdụ ụgbọ ala mgbe ị na-ekewa, iji gbochie ịgbagọ nke ogwe mgbapụta)
• 5 nke disassembly usoro nke mgbapụta bụ: (lee ọnụ ọgụgụ 1) mmiri ntinye ngalaba, impeller, diversion shei, impeller ...... lelee valvụ ahụ, mgbe ị na-ewepụ ihe mgbochi ahụ, jiri ngwá ọrụ pụrụ iche na-atọpụ ogwe aka conical nke edoziri. impeller mbụ, ma zere ịgbagọ na ihichapụ ogwe mgbapụta n'ime usoro nkesa.
• 6 usoro disassembly nke moto bụ: (lee ọnụ ọgụgụ 1) tinye moto n'elu ikpo okwu, na wepụ mkpụrụ, isi, aro isi kpochidoro aku, ịkwanye efere, igodo, ala ndu ibu oche na okpukpu abụọ isi bolt si na ala nke. moto n'aka nke ya, wee wepụ rotor (leba anya ka ị ghara imebi ngwugwu waya) na n'ikpeazụ wepụ ngalaba njikọ na oche oche nduzi elu.
• 7 unit mgbakọ: tupu mgbakọ, nchara na unyi nke akụkụ kwesịrị kpochara, na mating elu na fasteners ntekwasa na sealant, na mgbe ahụ gbakọtara na-emegide usoro nke disassembly (moto aro na-akpali elu na ala mgbe mgbakọ maka ihe dị ka otu onye. millimita), mgbe mgbakọ gachara, njikọ ahụ kwesịrị ịdị na-agbanwe agbanwe, mgbe ahụ igwe nyocha ihuenyo nzacha. A ga-ewepụ nfuli mmiri na-asọ asọ n'olulu mmiri maka ịkwatu na mmezi dị ka Nkeji edemede 5 mgbe otu afọ arụchara ọrụ, ma ọ bụ ihe na-erughị otu afọ nke ọrụ mana afọ abụọ nke oge mmiri mmiri, a ga-edochikwa akụkụ ndị ahụ eyighị.

 In order to ensure the long-term use and stable performance of submersible electric pump, we have launched a convenient and practical product. The product has a unique design, easy operation, and is perfect for various application scenarios. After use, remember to discharge all the water in the electric pump, especially in winter, so as not to freeze the motor. Wind the cable and bundle it. Store it in an environment without corrosive substances and gases, and keep the temperature below 40 °C. In addition, if you do not use it for a long time, you should pay attention to prevent the submersible electric pump from rusting. Choose our products to make your work more convenient and efficient.

01 Mmiri olulu mmiri miri emi

02 Mmiri mmiri dị elu

03 mmiri mmiri ugwu 

04 ụlọ elu mmiri

05 Agricultural ogbugba mmiri n'ubi

06 ogbugba mmiri n'ubi

07 oriri mmiri osimiri

08 mmiri ụlọ