Water Filled Submersible Pump

Usoro ọkụ eletrik QS usoro submersible bụ ụdị ọhụrụ nke ogbugba mmiri n'ubi na igwe drainage. Usoro nfuli a bụ vetikal, na-eji radial positive na negative guide vane design, obere olu, ịdị arọ dị arọ, elu elu, nrụnye dị mfe na mmegharị, nhazi na ọrụ dị mfe.

 Oke ọsọ 5-50m3 / h, ebuli 5-800m.

The product is equipped with three-phase AC 380V (tolerance is ± 5%), 50 Hz (tolerance is ± 1%) power supply. Water quality requirements are:

(1) water temperature shall not be higher than 20 °C;

(2) ọdịnaya adịghị ọcha siri ike (oke oke) agaghị adị karịa 0.01%;

(3) PH uru (pH) bụ 6.5-8.5;

(4) hydrogen sulfide ọdịnaya ekwesịghị ịbụ ihe karịrị 1.5 mg / L;

(5) Ọdịnaya ion chloride agaghị adị karịa 400 mg / L. Moto bụ ihe mgbochi mmiri mechiri emechi ma ọ bụ mmiri jupụtara.

Tupu eji ya, oghere dị n'ime nke moto submersible ga-ejupụta na mmiri dị ọcha, a ga-emesikwa mmịpụta mmiri na ikuku ikuku, ma ọ bụghị ya, a gaghị eji ya. A ghaghị ịmịnye mmiri mmiri na-ekpuchi mmiri kpamkpam na mmiri iji rụọ ọrụ, omimi ntinye agaghị agafe mita 70, na anya dị n'etiti ala nke mgbapụta mmiri na ala nke olulu mmiri ekwesịghị ịbụ ihe na-erughị mita 3. Mmiri mmiri nke ọma ga-egbo mkpa mmiri na-arụ ọrụ na-aga n'ihu na-arụ ọrụ nke mgbapụta mmiri na-ekpo ọkụ, na mmepụta mmiri nke mgbapụta mmiri na-ekpo ọkụ ga-achịkwa na 0.7-1.2 ugboro na-agba ọsọ. Ọmarịcha ahụ ga-abụ nke kwụ ọtọ, na mgbapụta submersible enweghị ike iji kwụ ọtọ ma ọ bụ nwee mmasị, mana ọ bụ naanị kwụ ọtọ. Igwe mmiri na-ekpu mmiri ga-adakọrịrị na eriri ma nweekwa ngwaọrụ nchebe oke ibu dị na mpụga dịka achọrọ. A machibidoro mgbapụta nke submersible ikike ịnwale na-enweghị ibu mmiri.

1, nke ọma submersible mgbapụta maka mmiri dị ọcha, machibidoro ịsacha olulu mmiri ọhụrụ, na-agbapụta sedimenti na mmiri apịtị,

2, nke ọma mmiri mgbapụta voltaji ọkwa 380/50HZ, ojiji nke ọzọ voltaji akara ule nke submersible Motors mkpa ka ahaziri. Downhole cables ga-eji waterproof cable, ga-onwem na mmalite akụrụngwa, dị ka igbe nkesa, mmalite adịghị njikere kwesịrị inwe nkịtị moto keukwu ọrụ nchebe ọrụ, dị ka mkpụmkpụ sekit bufee nchebe, na-adọ nchebe, undervoltage nchebe, grounding nchebe, idling nchebe, na N'ọnọdụ ndị na-adịghị mma, ngwaọrụ nchebe kwesịrị ịbụ njem mmemme n'oge.

3, mgbapụta ahụ ga-abụrịrị ntụkwasị obi na usoro ntinye na ojiji. Amachibidoro n'aka na n'ụkwụ mgbochi mkpọpu-mkpụrụkpụ. Tupu ịwụnye na idobe mgbapụta ahụ, a ghaghị ebipụ ike ahụ. Ejiri ya n'ebe a na-eji mgbapụta ahụ eme ihe, a ghaghị ịde ya nke ọma "na-egbochi ọkụ eletrik". Tupu agbada n'olulu mmiri ma ọ bụ nrụnye, oghere moto ahụ ga-ejupụta na mmiri distilled ma ọ bụ mmiri oyi na-adịghị emebi emebi, ma kechie mkpuchi mmiri / igbapu.

4, mgbe ọrụ mkparịta ụka mpaghara nke mgbapụta ahụ, a ghaghị ịwụsa mmiri n'ime ụlọ mgbapụta iji mee ka mmanu rọba mma. Oge mmalite ngwa ngwa agaghị agafe otu sekọnd, lelee ma ntụzịaka ahụ ọ dị ka ntuziaka ntuziaka. Mgbe mgbapụta ahụ kwụ ọtọ, ṅaa ntị na nchekwa, gbochie ntụgharị na mmerụ ahụ.

5, siri ike dị ka ndokwa nke mgbapụta ebuli, eruba nso nke ojiji, iji gbochie ala eruba ma ọ bụ elu ebuli pumping ike, mkpali ibu na ndị ọzọ n'akụkụ nke eyi, moto bufee ọkụ 6, mgbe mgbapụta ala ọma. nha nke moto na nguzogide mkpuchi ala ekwesịghị ịbụ ihe na-erughị 100M, mgbe mmalite na-ekiri voltaji na nke ugbu a, lelee mkpuchi mkpuchi moto, ma ọ dabara na ihe ndị a chọrọ; mgbapụta nchekwa ọnọdụ okpomọkụ ma ọ bụrụ na-erughị kefriza ebe, kwesịrị akọrọ moto oghere mmiri, gbochie moto oghere mmiri ice mebiri mere site ala okpomọkụ.

The pump part is mainly composed of pump shaft, impeller, guide housing, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The main characteristics of this product are that the motor is a water-immersed three-phase asynchronous motor, and the motor cavity is filled with water to cool the motor and lubricate the bearing. The pressure regulating film at the bottom is used to adjust the pressure difference of the water body in the cavity caused by the temperature rise of the motor. In order to prevent the sand from entering the motor, the upper end of the motor shaft extension is equipped with two oil seals and installed a sand discharging ring, forming a sand prevention structure. At the same time, in order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft by a coupling, and the thrust bearing is installed under the motor. The lubrication of the whole product is water lubrication, and the motor stator winding is made of high quality submersible motor winding wire with high insulation performance. In addition, the pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Nkwadebe tupu echichi:
1. Lelee ma mgbapụta submersible na-ezute ọnọdụ ojiji yana oke akọwapụtara na ntuziaka.
2. Iji obiect dị arọ nke nwere dayameta hà nhata kachasị elu nke mgbapụta mmiri na-ekpuchi mmiri, tụọ ma inneldiameter nke olulu mmiri ahụ nwere ike dabara na mgbapụta mmiri, ma tụọ ma omimi nke ọma na-emezu ihe achọrọ nrụnye.
3. Lelee ma olulu mmiri ahụ ọ dị ọcha ma mmiri olulu mmiri ahụ ọ na-asọ oyi. Ejila mgbapụta ọkụ eletrik na-eme ka mmiri na-asachapụ apịtị welor na mmiri ájá ka ịzenarị mmebi nke mgbapụta ọkụ eletrik n'oge.
4. Lelee ma ọnọdụ nke welhead echichi mwekota dabara na ma ọ nwere ike iguzogide qualty nke dum unit.
5. Lelee ma ọ bụrụ na akụrụngwa mgbapụta submersible zuru ezu ma wụnye ya nke ọma dị ka eserese mgbakọ na mwepụ na akwụkwọ ntuziaka Wepụ ihuenyo nzacha ma gbanwee njikọ ahụ iji hụ ma ọ na-agbagharị na-agbanwe agbanwe.
6. Kpochapụ ihe nkedo mmiri ma jupụta oghere moto na mmiri dị ọcha, nke na-adịghị emebi emebi (dee. jide n'aka na ị ga-agbanye ya), wee mee ka mmiri sie ike. Mgbe awa 12 nke ịgbanye mmiri gasịrị, nguzogide mkpuchi nke moto ekwesịghị ịbụ ihe na-erughị 150M Q mgbe a tụrụ ya na tebụl ịma jijiji 500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Eserese usoro wiring cable nke agbakwunyere bụ nke a:

8. Jiri multimeter chọpụta ma ejikọrọ wires nke atọ na ma nkwụsi ike DC ọ dị oke nhata.
9. Lelee ma ikike sekit na transformer bubigara ibu, wee jikọọ ihe ngbanwe mkpuchi ibufe ma ọ bụ akụrụngwa mmalite. Hụ Tebụl 2 maka ụdị ụdị dị iche iche, wee wụsa ịwụ mmiri n'ime mgbapụta mmiri si na mmiri mgbapụta mmiri iji mee ka mmanu rọba dị na mgbapụta ahụ, wee debe mgbapụta ọkụ eletrik nke nwere ike ime ka ọ kwụ ọtọ na kwụ ọtọ. Malite (ọ bụghị ihe karịrị otu sekọnd) ma lelee ma ntụzịaka stereị ọ dabara na akara stereị. Ọ bụrụ na ọ bụghị, gbanwee njikọ abụọ ọ bụla nke eriri ụzọ atọ. Mgbe ahụ wụnye nzacha ma kwadebe ka ị gbadaa n'olulu mmiri ahụ. Ọ bụrụ na ejiri ya n'oge pụrụ iche (dịka ọwa mmiri, ọwa mmiri, osimiri, ọdọ mmiri, ọdọ mmiri, wdg), mgbapụta ọkụ eletrik ga-agbanyerịrị nke ọma.

(2) Akụrụngwa na akụrụngwa ntinye:
1. Otu ụzọ na-ebuli agbụ maka ihe karịrị tọn abụọ.
2. A tripod nwere ogologo kwụ ọtọ na-erughị mita anọ.
3. Ụdọ abụọ kwụgidere (ụdọ waya) nke nwere ike ibu ibu ihe karịrị otu ton (nwere ike ibu ibu nke nfuli mmiri zuru ezu).
4. Wụnye ụzọ abụọ nke clamps (splints).
5. Wrenches, hammers, screwdrivers, eletriki ngwaọrụ na ngwá, wdg.

(3) Nwụnye mgbapụta ọkụ eletrik:
1. E gosipụtara eserese nrụnye nke mgbapụta ọkụ eletrik submersible na eserese 2. A na-egosipụta akụkụ ntinye kpọmkwem na Tebụl 3 "Ndepụta nke nrụnye akụkụ nke mgbapụta ọkụ eletrik".

2. Enwere ike ibunye nfuli eletriki na-ekpuchi isi na isi ihe na-erughị mita 30 ozugbo n'ime olulu mmiri site na iji ụdọ na eriri waya ma ọ bụ eriri hemp ndị ọzọ nwere ike iburu igwe zuru oke nke igwe dum, ọkpọkọ mmiri na mmiri na ọkpọkọ.

3. Nfuli nke nwere isi ihe karịrị mita 30 na-eji ọkpọkọ ígwè, na usoro ntinye bụ nke a:
① Jiri ihe nkedo iji kpoo njedebe elu nke akụkụ mgbapụta mmiri (a na-ejikọta moto na mmiri mgbapụta n'oge a), bulite ya na agbụ nke nghọta, ma jiri nwayọọ nwayọọ kechie ya n'ime olulu mmiri ruo mgbe ịtinye ihe nkedo na isi mmiri ma wepụ ya. nghọta yinye.
② Jiri ụzọ mkpị ọzọ kụchie ọkpọkọ, were yinye kwụgidere 15 cm pụọ na flange, wee wetuo ya nwayọ. N'etiti ọkpọkọ flange na mgbapụta flange Tinye ihe mgbochi rọba n'ebe ma mee ka ọkpọkọ ahụ sie ike ma gbapụta ya nke ọma na bolts, mkpụrụ na mmiri mmiri.
③ Welite obere mgbapụta submersible, wepụ ihe nkedo dị na nsọtụ elu nke mgbapụta mmiri ahụ, kechie eriri ahụ nke ọma na ọkpọkọ mmiri na teepu rọba, ma jiri nwayọọ nwayọọ kechie ya ruo mgbe etinyere mkpọ ahụ n'isi olulu mmiri.
④ Jiri otu usoro ahụ kee ọkpọkọ mmiri niile n'ime olulu mmiri.
⑤ Mgbe ejikọtara eriri na-eduga na njikwa njikwa, a na-ejikọta ya na ọkụ ọkụ nke atọ.

(4) Ihe ị ga-ahụ n'oge echichi:
1. Ọ bụrụ na achọpụtara ihe mgbagwoju anya n'oge usoro mgbapụta ahụ, tụgharịa ma ọ bụ dọrọ ọkpọkọ mmiri iji merie ebe nkwụsị. Ọ bụrụ na usoro dị iche iche ka na-arụ ọrụ, biko Amanyela mgbapụta ahụ ka ọ ghara imebi mgbapụta ọkụ eletrik na olulu mmiri.
2. N'oge echichi, a ga-etinye ihe mkpuchi rọba na flange nke ọkpọkọ ọ bụla ma mee ka ọ sie ike.
3. Mgbe a na-agbanye mmiri mmiri n'ime olulu mmiri ahụ, a ga-etinye ya n'etiti ọkpọkọ nke ọma iji gbochie mgbapụta ahụ na-agba ọsọ megide mgbidi olulu mmiri ruo ogologo oge, na-eme ka mgbapụta ahụ na-ama jijiji na moto na-ekpochapụ ma gbaa ọkụ. .
4. Kpebie omimi nke mgbapụta mmiri na ala nke olulu mmiri dịka ájá na-asọ asọ na ọnọdụ silt nke olulu mmiri ahụ. Eliela mgbapụta n'ime apịtị. Ebe dị anya site na mgbapụta mmiri na ala nke olulu mmiri n'ozuzu ọ bụghị ihe na-erughị mita 3 (lee foto 2).
5. Ihe omimi ntinye mmiri nke mgbapụta mmiri kwesịrị ịbụ ihe na-erughị 1-1.5 mita site na mmiri dị ike na ọnụ mmiri ntinye mmiri (lee foto 2). Ma ọ bụghị ya, a ga-emebi bearings mgbapụta mmiri n'ụzọ dị mfe.
6. Ebuli nke mgbapụta mmiri enweghị ike ịdị ala. Ma ọ bụghị ya, ekwesịrị itinye valvụ ọnụ ụzọ ámá na pipeline mmiri nke ọma iji chịkwaa mgbapụta mgbapụta na ebe a na-agbapụta agbapụta iji gbochie moto ahụ ka ọ ghara ibufe ma gbaa ọkụ n'ihi nnukwu ọnụọgụ mmiri.
7. Mgbe mgbapụta mmiri na-agba ọsọ, mmepụta mmiri kwesịrị ịdị na-aga n'ihu na ọbụna, nke dị ugbu a kwesịrị ịdị na-eguzosi ike (n'okpuru ọnọdụ ọrụ a kwadoro, n'ozuzu ọ dịghị ihe karịrị 10% nke akara ugbu a), na e kwesịghị inwe mkpọtụ ma ọ bụ mkpọtụ. Ọ bụrụ na enwere ihe na-adịghị mma, a ga-akwụsị igwe ahụ iji chọpụta ihe kpatara ya ma kpochapụ ya.
8. Mgbe ị na-etinye ya, ṅaa ntị na ntọala nke waya mgbanaka moto (lee foto 2). Mgbe ọkpọkọ mmiri bụ ọkpọkọ ígwè, dupụta ya site na mkpọchi olulu mmiri; mgbe ọkpọkọ mmiri bụ ọkpọkọ plastik, duga ya site na akara ala nke mgbapụta eletrik.

The use of underwater pumps need to be carried out in strict accordance with the following steps: First of all, after the installation of the underwater pump, it is necessary to recheck the insulation resistance and the three-phase continuity of the switch, and check whether there are errors in the connection of the instrument and the start equipment. If there is no problem, you can start to test the machine. After the start, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, please observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. The second step, after the pump runs for four hours for the first time, it should be closed and the thermal insulation resistance of the motor should be tested quickly. Its value should not be less than 0.5 megaohm. The third step, after the pump stops, it should be restarted after five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to excessive current. The fourth step, after the pump is put into normal operation, in order to prolong its service life, it is necessary to check the power supply voltage, operating current and insulation resistance regularly to see if they are normal. If the following conditions are found, the machine should be shut down immediately to troubleshoot:

1 the current exceeds 20% under the rated working conditions.

2 the dynamic water level drops to the inlet section, causing intermittent drainage.

3 the underwater pump vibrates violently or makes a lot of noise.

4 the supply voltage is lower than 340 volts.

5 a fuse burned. 6 water pipe damage.

7 the motor to the ground thermal insulation resistance is less than 0.5 megaohms.

The fifth step, the removal of the unit:

1 untie the cable tether, remove the pipe part, and remove the line protection plate.

2 screw down the water bolt and discharge all the water in the motor chamber.

3 remove the filter and loosen the fixing screw on the coupling fixed motor shaft.

4 screw down the bolt connecting the water inlet section and the motor, separate the pump and the motor (pay attention to make the unit level to prevent the bending of the pump shaft when separating)

5 the removal sequence of the pump is: (see Figure 1) water inlet section, impeller, shunt shell, impeller, check valve body. When removing the impeller, use special tools to loosen the cone sleeve fixed the impeller. In the process of removal, avoid bending the pump shaft and damage the various parts.

6 the removal process of the motor is: (see Figure 1) put the motor on the platform, and in order from the bottom of the motor bolt nuts, base, shaft head lock nut, thrust plate, key and lower guide bearing seat (iron rod bolt) on the connecting parts, and then take out the stator (careful not to damage the wire packet), and finally remove the connecting part and the upper guide bearing seat. Unit assembly: before assembly, rust and dirt on each component should be cleaned and sealant should be applied to each mating surface and fastener, and then the assembly should be carried out in reverse order of disassembly (the motor shaft moves about 1 mm after assembly), the coupling should be flexible after assembly, and then the filter should be put on for testing. Step six, after each use of the underwater electric pump operation for one year, or less than one year but immersed for two years, the disassembly and inspection should be carried out in accordance with the provisions of Article 5 to replace the worn parts.

 1, wepụta mmiri n'ime oghere moto (karịsịa n'oge oyi iji gbochie moto ahụ ka ọ ghara ịnwụ), ma kee eriri ahụ nke ọma.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 3, ogologo oge ojiji kwesịrị ịṅa ntị na nchara mgbochi nke submersible nfuli.

01 Mmiri olulu mmiri miri emi

02 Mmiri mmiri dị elu

03 mmiri mmiri ugwu

04 ụlọ elu mmiri

05 Agricultural ogbugba mmiri n'ubi

06 ogbugba mmiri n'ubi

07 oriri mmiri osimiri

08 mmiri ụlọ