175QJP Peep Well Submersible Pump

QJP series fountain pump is a special pump for fountain developed by our factory.The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, good magnetic conductivity, and frequent start will not fever.Both ends of the motor rotor use water as lubricant alloy copper sleeve.Stainless steel sleeve instead of ball bearings, to avoid the problem of easy rust ball bearings and lack of oil wear and tear the motor.The most suitable for music fountain use, all models can be used.

This product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply system. Applicable water quality conditions include water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L. The motor is a closed or water-filled wet structure. Before use, it must be filled with clean water to prevent false filling, and then tighten the water injection and exhaust bolts, otherwise it is not allowed to use. The submersible pump must be completely immersed in water, and the penetration depth shall not exceed 70m. The distance between the submersible pump base and the bottom of the well shall not be less than 3m. The well flow shall be able to meet the water output and continuous operation of the submersible pump. The water output of the submersible pump shall be controlled at 0.7-1.2 times of the rated flow. The well shall be vertical, and the submersible pump can not be used horizontally or upside down, but only vertically. The submersible pump shall be equipped with cables and external overload protection devices as required. The pump is strictly prohibited from no-load test without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, mosamalitsa molingana ndi zomwe zimaperekedwa pakukweza pampu, kuchuluka kwa magwiridwe antchito, kuteteza kutsika kochepa kapena mphamvu yopopa kwambiri, kukakamiza ndi mbali zina zakuvala, kuchuluka kwa magalimoto kumawotchedwa.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The main features of the product include: the motor is a water immersed wet three-phase asynchronous motor, the motor cavity is full of water, used to cool the motor and lubricate the bearing; the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of temperature; in order to prevent the sand particles in the well water from entering the motor, two oil seals are installed on the upper end of the motor shaft extension, and a sand control structure is formed by installing the sand ring; in order to prevent the pump shaft from jumping at startup, the pump shaft is connected with the motor shaft through a coupling, and the thrust bearing is installed under the motor; the lubrication of the motor and the pump bearing is water lubrication; the stator winding of the motor is made of high quality submersible motor winding, with high insulation performance; the pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Kukonzekera musanakhazikitse:
1. Yang'anani ngati pampu ya submersible ikugwirizana ndi momwe amagwiritsidwira ntchito komanso kukula kwake komwe kwafotokozedwa m'bukuli.
2. Pogwiritsa ntchito obiect yolemetsa yokhala ndi m'mimba mwake yofanana ndi kukula kwakunja kwa pampu ya submersible, yesani ngati innneldiameter ya chitsimecho ingagwirizane ndi mpope wa submersible, ndikuyesa ngati kuya kwa chitsime kumakwaniritsa zofunikira zoikamo.
3. Yang'anani ngati chitsime chili choyera komanso ngati madzi a m'chitsime ali abwibwi. Musagwiritse ntchito pampu yamagetsi ya submersible kutsuka matope a welor mpope ndi madzi amchenga kuti mupewe kuwonongeka msanga kwa pampu yamagetsi ya submersible.
4. Yang'anani ngati malo achitsulo choyika welhead ndi oyenera komanso ngati angapirire kuchuluka kwa gawo lonse.
5. Yang'anani ngati zigawo za pampu za submersible zatha ndikuyikidwa bwino molingana ndi chithunzi cha msonkhano chomwe chili m'mabuku Chotsani chophimba cha fyuluta ndikuzungulira cholumikizira kuti muwone ngati chimasinthasintha.
6. Chotsani zowononga zamadzi ndikudzaza pabowo lamoto ndi madzi oyera, osawononga (zindikirani. Onetsetsani kuti mwasefa), ndiyeno khwimitsani chopoperapo madzi. Pambuyo pa maola 12 a jakisoni wamadzi, kukana kwa injini sikuyenera kukhala kochepera 150M Q poyesedwa ndi tebulo logwedezeka la 500V.
7. Cholumikizira chingwe, dulani chingwe cha rabara cha 120mm kumapeto kwa chingwe chotuluka ndi chingwe chofananira chokhala ndi mpeni wamagetsi, kenaka mawaya atatu apakati agwedezeke mumpangidwe wopindika, chotsa pakati pa mkuwa wa 20mm, pukuta ndi oxide. wosanjikiza kunja kwa waya wamkuwa ndi mpeni kapena nsalu ya mchenga, ndikuyika malekezero a waya awiri olumikizidwa palirs.Mutamanga wosanjikiza mwamphamvu ndi waya wabwino wamkuwa, gulitsani bwino komanso mwamphamvu, ndi mchenga wamtundu uliwonse. ziphuphu pamwamba. Kenako, pamalumikizidwewo atatuwo, gwiritsani ntchito tepi yotsekera ya polyvester kuti mukulungidwe mwapang'onopang'ono kwa mabeseni atatu. Manga nsonga ziwiri za wosanjikizawo molimba ndi ulusi wa nyion, ndiyeno gwiritsani ntchito njira yotsekera pang'onopang'ono kukulunga tepiyo magawo atatu. Manga chosindikizira chakunja ndi tepi yotchinga kwambiri yamagulu atatu. Pomaliza, pindani zingwe zitatuzo pamodzi ndikuzikulunga mobwerezabwereza kwa magawo asanu ndi tepi yothamanga kwambiri. Chigawo chilichonse chiyenera kumangiriridwa mwamphamvu, ndipo zolumikizira zolumikizirana ziyenera kukhala zolimba komanso zolimba kuti madzi asalowe ndikuwononga kutsekeka, Pambuyo kukulunga, zilowerereni m'madzi kutentha kwa 20 'c kwa maola 12, ndikuyesa kukana kwachitetezo ndi tebulo logwedezeka. , yomwe sayenera kuchepera 100M Ω

Chiwonetsero cha njira yolumikizira chingwe chili motere:

8. Gwiritsani ntchito multimeter kuti muwone ngati mawaya a magawo atatu alumikizidwa komanso ngati kukana kwa DC kuli pafupifupi moyenera.
9. Yang'anani ngati mphamvu yozungulira ndi thiransifoma yadzaza kwambiri, ndiyeno gwirizanitsani chotchinga choteteza katundu kapena zida zoyambira. Onani Table 2 kuti mupeze zitsanzo zenizeni, ndiyeno Thirani ndowa yamadzi mu mpope wa madzi kuchokera popopa madzi kuti mutsitsire ma bere a rabara mu mpope, ndiyeno ikani mpope wamagetsi wozama mowongoka ndi wosasunthika. Yambani (osaposa sekondi imodzi) ndikuwona ngati chiwongolerocho chikugwirizana ndi chiwongolero. Ngati sichoncho, sinthanani zolumikizira ziwiri za chingwe cha magawo atatu. Kenako yikani fyuluta ndikukonzekera kutsika pachitsime. Ngati amagwiritsidwa ntchito pazochitika zapadera (monga ngalande, ngalande, mitsinje, maiwe, maiwe, ndi zina zotero), mpope wamagetsi uyenera kukhazikika pansi.

(2) Zida zoyika ndi zida:
1. Peyala imodzi ya unyolo wonyamulira woposa matani awiri.
2. Tripod yokhala ndi utali woyima wosachepera mamita anayi.
3. Zingwe ziwiri zolendewera (zingwe za waya) zomwe zimatha kunyamula kulemera kopitilira tani imodzi (zimatha kunyamula ma pampu athunthu amadzi).
4. Ikani zingwe ziwiri ziwiri (zolumikizira).
5. Wrenches, nyundo, screwdrivers, zida zamagetsi ndi zida, etc.

(3) Kuyika pampu yamagetsi:
1. Chojambula choyikapo cha pampu yamagetsi ya submersible chikuwonetsedwa mu Chithunzi 2. Miyeso yeniyeni yoyika ikuwonetsedwa mu Table 3 "Mndandanda wa Miyeso ya Kuyika kwa Pampu ya Magetsi Oyikirapo".

2. Mapampu amagetsi oyenda pansi pamadzi okhala ndi mutu wosakwana mamita 30 akhoza kukwezedwa molunjika kuchitsime pogwiritsa ntchito mapaipi ndi zingwe za waya kapena zingwe zina za hemp zomwe zimatha kunyamula kulemera kwa makina onse, mapaipi amadzi, ndi madzi mu mapaipi.

3. Mapampu okhala ndi mutu wopitilira 30 metres amagwiritsa ntchito mapaipi achitsulo, ndipo kuyika kwake kuli motere:
①Gwiritsani ntchito chotchinga kuti mutseke kumtunda kwa gawo la mpope wamadzi (motor ndi mpope wamadzi zalumikizidwa pakadali pano), kwezani ndi unyolo wolendewera, ndikumangirira pang'onopang'ono m'chitsime mpakaIkani chingwe pamutu ndikuchotsani. unyolo wopachika.
② Gwiritsani ntchito zingwe zina kuti mutseke chitoliro, ikwezeni ndi unyolo wolendewera wa masentimita 15 kuchokera ku flange, ndikutsitsa pang'onopang'ono. Pakati pa chitoliro cha chitoliro ndi chopopera chopoperaIkani mphira m'malo mwake ndikumangitsani chitoliro ndikupopa mofanana ndi mabawuti, mtedza ndi zochapira masika.
③ Kwezani mpope wa submersible pang'ono, chotsani chotchinga chakumtunda kwa mpope wamadzi, kumangirira chingwe ku chitoliro chamadzi ndi tepi ya pulasitiki, ndikumangirira pang'onopang'ono mpaka Chingwecho chikayikidwa pachitsime.
④Gwiritsani ntchito njira yomweyo kumanga mapaipi onse amadzi pachitsime.
⑤Chingwe chotsogolera chikalumikizidwa ndi chosinthira chowongolera, chimalumikizidwa ndi gawo la magawo atatu.

(4) Zinthu zofunika kuziwona pakuyika:
1. Ngati chodabwitsa cha jamming chikupezeka panthawi yopopera, tembenuzirani kapena kukoka chitoliro cha madzi kuti mugonjetse malo ophimbidwa. Ngati njira zosiyanasiyana sizikugwirabe ntchito, chonde Musakakamize mpope pansi kuti mupewe kuwonongeka kwa pampu yamagetsi yozama komanso chitsime.
2. Pakuyika, mphira wa rabara uyenera kuikidwa pamphepete mwa chitoliro chilichonse ndikumangirira mofanana.
3. Pamene mpope wamadzi watsitsidwa m’chitsime, uyenera kuikidwa pakati pa chitoliro cha chitsimecho kuti mpopeyo usayendetse khoma la chitsime kwa nthawi yaitali, zomwe zimapangitsa kuti pampuyo igwedezeke ndipo injini ikusesa ndi kutentha. .
4. Dziwani kuya kwa mpope wamadzi mpaka pansi pa chitsime molingana ndi mchenga woyenda komanso silt ya pachitsime. Osakwirira mpope m'matope. Mtunda wochokera pa mpope wa madzi kufika pansi pa chitsime nthawi zambiri umakhala wosachepera mamita atatu (onani chithunzi 2).
5. Kuzama kwa madzi pa mpope kuyenera kukhala kosachepera 1-1.5 metres kuchokera pamadzi amphamvu kupita kumalo olowera madzi (onani Chithunzi 2). Kupanda kutero, mayendedwe a pampu amadzi amatha kuwonongeka mosavuta.
6. Kukweza kwa mpope wamadzi sikungakhale kotsika kwambiri. Kupanda kutero, valavu ya pachipata iyenera kuyikidwa papaipi yamadzi yakuchitsime kuti muzitha kuyendetsa pampu pamalo oyendera kuti injini isalemedwe ndikuwotchedwa chifukwa cha kuchuluka kwamadzi.
7. Pamene mpope wamadzi ukuyenda, kutuluka kwa madzi kuyenera kukhala kosalekeza komanso ngakhale, komweko kuyenera kukhala kosasunthika (pansi pa malo ogwirira ntchito, nthawi zambiri osapitirira 10% ya omwe adavotera panopa), ndipo pasakhale kugwedezeka kapena phokoso. Ngati pali vuto lililonse, makinawo ayimitsidwe kuti adziwe chomwe chayambitsa ndikuchichotsa.
8. Mukayika, mvetserani kuyika kwa waya wamoto (onani Chithunzi 2). Pamene chitoliro cha madzi ndi chitoliro chachitsulo, chitsogolereni kuchokera pachitsime chachitsulo; pamene chitoliro cha madzi ndi chitoliro cha pulasitiki, chitsogolereni kuchokera kumalo oyambira pampu yamagetsi.

• 1.After installing the submersible pump, recheck the insulation resistance and the three-phase continuity at the switch, and check whether there are errors in the connection of the instrument and the starting equipment.If there are no problems, you can start to test the machine. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump emits any noise or vibration. If everything is normal, it can be put into operation.
• 2. After the pump runs for the first four hours, the thermal insulation resistance of the motor should be closed and tested quickly.Its value should not be less than 0.5 megaohm.After the pump stops, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing and burning the motor due to excessive current.
• 3. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to troubleshoot.
•  
• 1 M'malo ogwirira ntchito omwe adavotera, panopo amaposa 20%.
• 2 Mulingo wamadzi wosunthika umatsikira kumalo olowera madzi, kupangitsa madzi apakatikati.
• 3 Pampu ya submersible imakhala ndi kugwedezeka kwakukulu kapena phokoso.
• 4 Mphamvu zamagetsi ndizotsika kuposa 340 volts.
• 5 Fuse yatenthedwa.
• 6 Paipi yoperekera madzi yawonongeka.
• 7 Kukana kwa injini yamagetsi ku geothermal state ndikotsika kuposa 0.5 megaohm.
•  
• Unit disassembly:
• 1.untie cable rope, remove the pipeline part, remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the inlet junction with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) inlet junction, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising of the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the reverse order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product adopts advanced design and provides advanced storage suggestions to ensure long-term use effect.First of all, in winter, it is necessary to exhaust all the water to prevent freezing. In addition, the wire rolls should be placed well and tied up.Secondly, when storing, the environment without corrosive action and gas should be selected and the temperature should be kept below 40 °C. Finally, when not used for a long time, attention should be paid to prevent rust of submersible pump.These storage requirements will ensure that the product can maintain its performance status and prolong its service life for a long time.

01 Kumwa madzi a pachitsime chakuya

02 Madzi okwera kwambiri

03 madzi a m'mapiri 

04 madzi nsanja

05 Kuthirira kwaulimi

06 ulimi wothirira m'munda

07 madzi a mitsinje

08 madzi apakhomo