175QJP Potopna črpalka Peep Well

QJP series fountain pump is a special pump for fountain developed by our factory.The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, good magnetic conductivity, and frequent start will not fever.Both ends of the motor rotor use water as lubricant alloy copper sleeve.Stainless steel sleeve instead of ball bearings, to avoid the problem of easy rust ball bearings and lack of oil wear and tear the motor.The most suitable for music fountain use, all models can be used.

This product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply system. Applicable water quality conditions include water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L. The motor is a closed or water-filled wet structure. Before use, it must be filled with clean water to prevent false filling, and then tighten the water injection and exhaust bolts, otherwise it is not allowed to use. The submersible pump must be completely immersed in water, and the penetration depth shall not exceed 70m. The distance between the submersible pump base and the bottom of the well shall not be less than 3m. The well flow shall be able to meet the water output and continuous operation of the submersible pump. The water output of the submersible pump shall be controlled at 0.7-1.2 times of the rated flow. The well shall be vertical, and the submersible pump can not be used horizontally or upside down, but only vertically. The submersible pump shall be equipped with cables and external overload protection devices as required. The pump is strictly prohibited from no-load test without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, strogo v skladu z določbami dvigala črpalke, obseg uporabe pretoka, za preprečevanje nizkega pretoka ali visokega dviga črpalne sile, potisni ležaj in drugi deli obrabe, preobremenitev motorja zgorela

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The main features of the product include: the motor is a water immersed wet three-phase asynchronous motor, the motor cavity is full of water, used to cool the motor and lubricate the bearing; the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of temperature; in order to prevent the sand particles in the well water from entering the motor, two oil seals are installed on the upper end of the motor shaft extension, and a sand control structure is formed by installing the sand ring; in order to prevent the pump shaft from jumping at startup, the pump shaft is connected with the motor shaft through a coupling, and the thrust bearing is installed under the motor; the lubrication of the motor and the pump bearing is water lubrication; the stator winding of the motor is made of high quality submersible motor winding, with high insulation performance; the pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Priprava pred namestitvijo:
1. Preverite, ali potopna črpalka ustreza pogojem uporabe in obsegu, navedenim v priročniku.
2. Z uporabo težkega predmeta s premerom, ki je enak največjemu zunanjemu premeru potopne črpalke, izmerite, ali notranji premer vrtine ustreza potopni črpalki, in izmerite, ali globina vrtine ustreza zahtevam za namestitev.
3. Preverite, ali je vrtina čista in ali je voda v vodnjaku motna. Nikoli ne uporabljajte potopne električne črpalke za izpiranje blata in peska črpalke welor, da preprečite prezgodnje poškodbe potopne električne črpalke.
4. Preverite, ali je položaj namestitvene objemke glave valja primeren in ali lahko prenese kakovost celotne enote
5. Preverite, ali so komponente potopne črpalke dokončane in pravilno nameščene v skladu s shemo sestavljanja v priročniku. Odstranite mrežico filtra in zavrtite sklopko, da vidite, ali se vrti prožno
6. Odvijte vodni vijak in napolnite votlino motorja s čisto, nejedko vodo (upoštevajte, da ste jo napolnili), nato privijte vodni vijak. Po 12 urah vbrizgavanja vode izolacijska upornost motorja ne sme biti manjša od 150 M Q, merjena s stresalno mizo 500 V.
7. Kabelski spoj, z električarskim nožem odrežite 120-milimetrski gumijasti tulec z enega konca izhodnega kabla in ustreznega kabla, nato stopničasto razporedite dolžino treh žilnih žic, odlepite 20-milimetrsko bakreno jedro, postrgajte oksid plast na zunanji strani bakrene žice z nožem ali krpo za peskanje in dva povezana konca žice vstavite v palirje. Ko plast tesno povežete s fino bakreno žico, jo temeljito in trdno spajkajte ter pobrusite poljubno. neravnine na površini. Nato za tri spoje uporabite izolacijski trak iz polivestra, da jih ovijete na pol naložen način za tri umivalnike. Oba konca ovojne plasti tesno ovijte z nyion nitjo in nato uporabite metodo pol zlaganja, da ovijete trak za tri plasti. Ovijte zunanji sloj z visokotlačnim izolacijskim trakom za tri plasti. Na koncu zložite tri pramene skupaj in jih večkrat ovijte v pet plasti z visokotlačnim trakom. Vsaka plast mora biti tesno povezana, vmesni spoji pa morajo biti tesni in čvrsti, da preprečite, da bi voda prodrla in poškodovala izolacijo. Po ovijanju namočite v vodi pri sobni temperaturi 20 °C za 12 ur in izmerite izolacijski upor s stresalno mizo , ki ne sme biti manjši od 100M Ω

Priloženi diagram postopka ožičenja kabla je naslednji:

8. Z multimetrom preverite, ali so trifazne žice priključene in ali je upor DC približno uravnotežen.
9. Preverite, ali sta vezje in zmogljivost transformatorja preobremenjena, nato priključite stikalo za zaščito pred preobremenitvijo ali opremo za zagon. Glejte tabelo 2 za določene modele in nato vlijte vedro vode v vodno črpalko iz izhoda vodne črpalke, da namažete gumijaste ležaje v črpalki, nato pa postavite potopno električno črpalko pokonci in mirno. Zaženite (ne več kot ena sekunda) in preverite, ali je smer krmiljenja skladna z znakom za krmiljenje. Če ne, zamenjajte poljubna dva konektorja trifaznega kabla. Nato namestite filter in se pripravite na spust v vodnjak. Če se uporablja v posebnih priložnostih (kot so jarki, jarki, reke, ribniki, ribniki itd.), mora biti električna črpalka zanesljivo ozemljena.

(2) Oprema in orodje za namestitev:
1. En par dvižnih verig za več kot dve toni.
2. Stativ z navpično višino najmanj štiri metre.
3. Dve viseči vrvi (žični vrvi), ki lahko preneseta težo več kot eno tono (lahko preneseta težo celotnega kompleta vodnih črpalk).
4. Namestite dva para sponk (splintov).
5. Ključi, kladiva, izvijači, električna orodja in instrumenti itd.

(3) Namestitev električne črpalke:
1. Namestitveni diagram potopne električne črpalke je prikazan na sliki 2. Posebne namestitvene mere so prikazane v tabeli 3 "Seznam namestitvenih mer potopne električne črpalke".

2. Potopne električne črpalke z višino manj kot 30 metrov je mogoče dvigniti neposredno v vodnjak s pomočjo cevi in ​​žičnih vrvi ali drugih vrvi iz konoplje, ki lahko prenesejo polno težo celotnega stroja, vodovodnih cevi in ​​vode v ceveh.

3. Črpalke z višino nad 30 metrov uporabljajo jeklene cevi, zaporedje namestitve pa je naslednje:
①Uporabite objemko, da vpnete zgornji konec dela vodne črpalke (motor in vodna črpalka sta bila trenutno povezana), jo dvignite z visečo verigo in počasi privežite v vodnjak, dokler ne namestite objemke na glavo vodnjaka in odstranite viseča veriga.
② Uporabite drug par sponk, da vpnete cev, jo dvignite z visečo verigo 15 cm stran od prirobnice in jo počasi spustite. Med prirobnico cevi in ​​prirobnico črpalke Namestite gumijasto podlogo in enakomerno zategnite cev in črpalko z vijaki, maticami in vzmetnimi podložkami.
③ Rahlo privzdignite potopno črpalko, odstranite objemko na zgornjem koncu vodne črpalke, kabel trdno privežite na vodno cev s plastičnim trakom in ga počasi privežite, dokler objemka ni nameščena na ustju vodnjaka.
④Uporabite isto metodo za pritrditev vseh vodovodnih cevi v vodnjak.
⑤Ko je izhodni kabel priključen na krmilno stikalo, je priključen na trifazno napajanje.

(4) Stvari, ki jih morate upoštevati med namestitvijo:
1. Če med postopkom črpanja odkrijete pojav zagozditve, obrnite ali povlecite cev za vodo, da premagate točko zagozdenja. Če različni ukrepi še vedno ne delujejo, vas prosimo, da črpalke ne spustite na silo, da preprečite poškodbe potopne električne črpalke in vodnjaka.
2. Med namestitvijo je treba na prirobnico vsake cevi namestiti gumijasto blazinico in jo enakomerno zategniti.
3. Ko vodno črpalko spustite v vodnjak, jo postavite na sredino cevi vodnjaka, da preprečite, da bi črpalka dlje časa delovala ob steni vodnjaka, zaradi česar bi črpalka vibrirala, motor pa pometal in gorel .
4. Določite globino vodne črpalke do dna vodnjaka glede na razmere tekočega peska in mulja v vodnjaku. Ne zakopajte črpalke v blato. Razdalja od vodne črpalke do dna vodnjaka običajno ni manjša od 3 metrov (glej sliko 2).
5. Globina vstopa vode vodne črpalke ne sme biti manjša od 1-1,5 metra od dinamičnega nivoja vode do vozlišča vstopa vode (glej sliko 2). V nasprotnem primeru se lahko ležaji vodne črpalke zlahka poškodujejo.
6. Dvig vodne črpalke ne sme biti prenizek. V nasprotnem primeru je treba na cevovod za vodo na ustju vrtine namestiti zaporni ventil za nadzor pretoka črpalke pri nazivni točki pretoka, da se prepreči preobremenitev in izgorevanje motorja zaradi velikih pretokov.
7. Ko vodna črpalka deluje, mora biti izhod vode neprekinjen in enakomeren, tok mora biti stabilen (pri nazivnih delovnih pogojih običajno ne več kot 10 % nazivnega toka) in ne sme biti vibracij ali hrupa. Če pride do kakršnih koli nepravilnosti, je treba stroj ustaviti, da ugotovite vzrok in ga odpravite.
8. Pri namestitvi bodite pozorni na nastavitev ozemljitvene žice motorja (glejte sliko 2). Če je cev za vodo jeklena cev, jo speljite od objemke na ustju vodnjaka; če je cev za vodo plastična cev, jo speljite od oznake za ozemljitev električne črpalke.

• 1.After installing the submersible pump, recheck the insulation resistance and the three-phase continuity at the switch, and check whether there are errors in the connection of the instrument and the starting equipment.If there are no problems, you can start to test the machine. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump emits any noise or vibration. If everything is normal, it can be put into operation.
• 2. After the pump runs for the first four hours, the thermal insulation resistance of the motor should be closed and tested quickly.Its value should not be less than 0.5 megaohm.After the pump stops, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing and burning the motor due to excessive current.
• 3. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to troubleshoot.
•  
• 1 V nazivnem delovnem stanju tok presega 20 %.
• 2 Dinamični nivo vode pade do odseka za dovod vode, kar povzroči občasno nastajanje vode.
• 3 Potopna črpalka povzroča močne vibracije ali hrup.
• 4 Napajalna napetost je nižja od 340 voltov.
• 5 Varovalka je pregorela.
• 6 Cev za dovod vode je poškodovana.
• 7 Izolacijska upornost motorja glede na geotermalno stanje je manjša od 0,5 megaohma.
•  
• Unit disassembly:
• 1.untie cable rope, remove the pipeline part, remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the inlet junction with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) inlet junction, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising of the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the reverse order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product adopts advanced design and provides advanced storage suggestions to ensure long-term use effect.First of all, in winter, it is necessary to exhaust all the water to prevent freezing. In addition, the wire rolls should be placed well and tied up.Secondly, when storing, the environment without corrosive action and gas should be selected and the temperature should be kept below 40 °C. Finally, when not used for a long time, attention should be paid to prevent rust of submersible pump.These storage requirements will ensure that the product can maintain its performance status and prolong its service life for a long time.

01 Zajem vode iz globokega vodnjaka

02 Visoka oskrba z vodo

03 gorski vodovod 

04 stolpna voda

05 Namakanje v kmetijstvu

06 namakanje vrta

07 zajetje rečne vode

08 gospodinjska voda