175QJP Peep Well Submersible Pump

QJP series fountain pump is a special pump for fountain developed by our factory.The pump motor core is made of high quality cold rolled silicon steel, which makes the pump more efficient, good magnetic conductivity, and frequent start will not fever.Both ends of the motor rotor use water as lubricant alloy copper sleeve.Stainless steel sleeve instead of ball bearings, to avoid the problem of easy rust ball bearings and lack of oil wear and tear the motor.The most suitable for music fountain use, all models can be used.

This product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply system. Applicable water quality conditions include water temperature not exceeding 20 °C, solid impurities content (mass ratio) is not greater than 0.01%, PH value (pH) is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L. The motor is a closed or water-filled wet structure. Before use, it must be filled with clean water to prevent false filling, and then tighten the water injection and exhaust bolts, otherwise it is not allowed to use. The submersible pump must be completely immersed in water, and the penetration depth shall not exceed 70m. The distance between the submersible pump base and the bottom of the well shall not be less than 3m. The well flow shall be able to meet the water output and continuous operation of the submersible pump. The water output of the submersible pump shall be controlled at 0.7-1.2 times of the rated flow. The well shall be vertical, and the submersible pump can not be used horizontally or upside down, but only vertically. The submersible pump shall be equipped with cables and external overload protection devices as required. The pump is strictly prohibited from no-load test without water.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, nruj me ntsis raws li cov kev cai ntawm lub twj tso kua mis nqa, ntws ntau yam ntawm kev siv, los tiv thaiv qis ntws los yog siab nqa twj tso kua mis quab yuam, lub thrust bearing thiab lwm yam ntawm hnav, lub cev muaj zog overload hlawv.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part mainly includes base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand ring, water inlet section, lead cable and other components. The main features of the product include: the motor is a water immersed wet three-phase asynchronous motor, the motor cavity is full of water, used to cool the motor and lubricate the bearing; the pressure regulating film at the bottom of the motor is used to adjust the expansion and contraction pressure difference of the internal water caused by the change of temperature; in order to prevent the sand particles in the well water from entering the motor, two oil seals are installed on the upper end of the motor shaft extension, and a sand control structure is formed by installing the sand ring; in order to prevent the pump shaft from jumping at startup, the pump shaft is connected with the motor shaft through a coupling, and the thrust bearing is installed under the motor; the lubrication of the motor and the pump bearing is water lubrication; the stator winding of the motor is made of high quality submersible motor winding, with high insulation performance; the pump is designed by computer CAD, with simple structure and excellent technical performance.

(1) Kev npaj ua ntej installation:
1. Xyuas seb lub twj tso kua mis submersible puas ua tau raws li qhov kev siv thiab qhov tshwj xeeb hauv phau ntawv qhia.
2. Siv lub qhov hnyav obiect nrog txoj kab uas hla sib npaug rau qhov siab tshaj plaws sab nraud ntawm lub twj tso kua mis submersible, ntsuas seb qhov inneldiameter ntawm lub qhov dej puas tuaj yeem haum rau lub twj tso kua mis submersible, thiab ntsuas seb qhov dej tob puas ua tau raws li qhov yuav tsum tau ua.
3. Xyuas seb lub qhov dej puas huv si thiab seb cov dej hauv qhov dej puas yog turbid. Tsis txhob siv lub tshuab hluav taws xob submersible los ntxuav lub welor twj av nkos thiab dej xuab zeb kom tsis txhob muaj kev puas tsuaj ntxov rau lub tshuab hluav taws xob submersible.
4. Tshawb xyuas seb txoj haujlwm ntawm lub welhead installation clamp puas haum thiab seb nws puas tuaj yeem tiv taus qhov zoo ntawm tag nrho chav tsev.
5. Tshawb xyuas seb cov twj tso kua dej submersible puas ua tiav thiab teeb tsa kom raug raws li daim duab sib dhos hauv phau ntawv tshem tawm cov ntxaij lim dej thiab tig lub coupling kom pom tias nws tig tau yooj yim.
6. Unscrew cov dej ntsia hlau thiab sau cov kab noj hniav nrog cov dej huv, tsis muaj corrosive (ceeb toom. Nco ntsoov sau nws), tom qab ntawd ceev cov dej screws. Tom qab 12 teev ntawm kev txhaj tshuaj dej, qhov rwb thaiv tsev ntawm lub cev muaj zog yuav tsum tsis txhob tsawg dua 150M Q thaum ntsuas nrog 500V co lub rooj.
7. Cable sib koom tes, txiav tawm lub tes tsho roj hmab 120mm los ntawm ib kawg ntawm cov khoom siv tawm thiab cov khoom sib txuam nrog ib tus neeg siv hluav taws xob riam, stagger qhov ntev ntawm peb cov xov hlau nyob hauv ib kauj ruam, tev tawm 20mm tooj liab tub ntxhais, txhuam cov oxide. txheej nyob rau sab nraud ntawm cov hlau tooj liab nrog ib rab riam los yog cov ntaub xuab zeb, thiab ntxig rau ob txoj hlua txuas rau hauv palir. burrs ntawm qhov chaw. Tom qab ntawd, rau peb lub pob qij txha, siv polyvester rwb thaiv tsev daim kab xev los qhwv lawv nyob rau hauv ib tug semi stacked yam rau peb lavers. Qhwv ob qhov kawg ntawm txheej txheej nruj nreem nrog nyion xov, thiab tom qab ntawd siv cov txheej txheem semi stacked los qhwv daim kab xev rau peb txheej. qhwv lub outellaer nrog high-pressure rwb thaiv tsev daim kab xev rau peb txheej. Thaum kawg, quav peb txoj hlua ua ke thiab rov qhwv lawv rau tsib txheej nrog daim kab xev siab. Txhua txheej yuav tsum tau nruj nreem khi, thiab cov interlayer pob qij txha yuav tsum nruj thiab fimm kom tsis txhob muaj dej los ntawm kev nkag mus thiab ua puas lub rwb thaiv tsev, Tom qab qhwv, tsau nyob rau hauv dej ntawm chav tsev kub ntawm 20 'c rau 12 teev, thiab ntsuas lub rwb thaiv tsev tiv thaiv nrog ib tug co lub rooj. , uas yuav tsum tsis pub tsawg tshaj 100M Ω

Daim duab txuas cable thaiv txheej txheem yog raws li hauv qab no:

8. Siv multimeter los xyuas seb cov xov hlau peb-theem puas txuas thiab seb qhov DC tsis kam yog kwv yees li qhov sib npaug.
9. Xyuas seb puas muaj peev xwm ntawm lub Circuit Court thiab transformer yog overloaded, thiab ces txuas lub overload tiv thaiv hloov los yog pib cov khoom. Saib Table 2 rau cov qauv tshwj xeeb, thiab tom qab ntawd hliv ib lub thoob dej rau hauv lub twj tso kua mis los ntawm lub qhov dej twj tso kua mis kom lubricate cov roj hmab bearings hauv lub twj tso kua mis, thiab tom qab ntawd muab lub twj tso kua mis submersible fais fab tso ncaj thiab khov kho.Start (tsis pub ntau tshaj ib ob) thiab xyuas seb qhov kev taw qhia lub kauj tsheb puas zoo ib yam nrog lub kauj tsheb. Yog tias tsis yog, sib pauv ob qhov txuas ntawm peb-theem cable.Tom qab ntawd nruab lub lim thiab npaj mus rau hauv qhov dej. Yog tias siv rau lub sijhawm tshwj xeeb (xws li kwj dej, kwj dej, dej ntws, pas dej, pas dej, thiab lwm yam), lub twj tso kua mis hluav taws xob yuav tsum muaj kev ntseeg siab.

(2) Kev teeb tsa thiab cov cuab yeej siv:
1. Ib khub nqa cov hlua rau ntau tshaj ob tons.
2. Lub tripod nrog ib txoj kab ntsug qhov siab tsis pub tsawg tshaj plaub meters.
3. Ob txoj hlua dai (xov hlau hlua) uas tuaj yeem nqa tau qhov hnyav ntawm ntau tshaj ib tuj (tuaj yeem lav qhov hnyav ntawm cov twj tso kua dej tiav).
4. Nruab ob khub ntawm clamps (splnts).
5. Wrenches, hammers, ntswj ntsia hlau, cov cuab yeej hluav taws xob thiab cov twj paj nruag, thiab lwm yam.

(3) Hluav taws xob twj tso kua mis installation:
1. Daim duab qhia kev teeb tsa ntawm lub tshuab hluav taws xob submersible yog pom nyob rau hauv daim duab 2. Qhov tshwj xeeb installation qhov ntev yog qhia nyob rau hauv Table 3 "Daim Ntawv Teev Tseg Qhov Loj ntawm Submersible Electric Pump".

2. Cov twj siv hluav taws xob submersible nrog lub taub hau tsawg dua 30 meters tuaj yeem nqa ncaj qha mus rau hauv lub qhov dej siv cov hoses thiab cov hlua hlau lossis lwm cov hlua hemp uas tuaj yeem nqa tau qhov hnyav tag nrho ntawm lub tshuab, cov kav dej, thiab dej hauv cov kav dej.

3. Cov twj tso kua mis nrog lub taub hau ntau dua 30 meters siv cov kav dej steel, thiab cov txheej txheem kev teeb tsa yog raws li hauv qab no:
①Siv lub clamp los tuav lub siab kawg ntawm lub twj tso kua mis (lub cev muaj zog thiab lub twj tso kua dej tau txuas rau lub sijhawm no), nqa nws nrog cov hlua khi, thiab maj mam khi nws mus rau hauv lub qhov dej kom txog thaum muab lub clamp rau ntawm lub qhov dej thiab tshem tawm qhov saw caj dab.
② Siv lwm ob lub clamps los tuav cov yeeb nkab, nqa nrog ib txoj hlua dai 15 cm deb ntawm lub flange, thiab maj mam txo qis. Nruab nrab ntawm cov yeeb nkab flange thiab lub twj tso kua mis flange Muab cov roj hmab tso rau hauv qhov chaw thiab nruj cov yeeb nkab thiab twj tso kua mis sib npaug nrog bolts, ceev thiab lub caij nplooj ntoos hlav ntxhua.
③ Nqa lub twj tso kua mis submersible me ntsis, tshem lub clamp ntawm lub taub dej kawg ntawm lub twj tso kua mis, khi lub cable kom ruaj khov rau hauv cov kav dej nrog ib daim kab xev yas, thiab maj mam khi nws kom txog thaum lub clamp muab tso rau ntawm lub qhov dej.
④ Siv tib txoj kev los khi tag nrho cov kav dej rau hauv qhov dej.
⑤ Tom qab cov hlau lead-tawm txuas nrog rau kev tswj kev hloov, nws txuas nrog peb-theem fais fab mov.

(4) Tej yam yuav tsum nco ntsoov thaum lub installation:
1. Yog tias pom muaj qhov tshwm sim jamming thaum lub sij hawm siv cov txheej txheem, tig los yog rub cov yeeb nkab dej kom kov yeej qhov jamming point. Yog tias ntau yam kev ntsuas tseem tsis ua haujlwm, thov tsis txhob yuam lub twj tso kua mis kom tsis txhob muaj kev puas tsuaj rau lub tshuab hluav taws xob submersible thiab lub qhov dej.
2. Thaum lub sij hawm installation, yuav tsum tau muab tso rau ntawm ib tug roj hmab ncoo nyob rau hauv lub flange ntawm txhua lub yeeb nkab thiab nruj nreem sib npaug zos rau.
3. Thaum lub twj tso kua dej qis rau hauv lub qhov dej, nws yuav tsum tau muab tso rau hauv nruab nrab ntawm lub qhov dej kom tsis txhob lub twj tso kua mis khiav tawm ntawm lub qhov dej mus ntev, ua rau lub twj tso kua mis vibrate thiab lub cev muaj zog cheb thiab hlawv. .
4. Txiav txim siab qhov tob ntawm lub twj tso kua mis dej mus rau hauv qab ntawm lub qhov dej raws li cov xuab zeb ntws thiab cov av ntawm lub qhov dej. Tsis txhob faus lub twj tso kua mis hauv av nkos. Qhov kev ncua deb ntawm lub twj tso kua dej mus rau hauv qab ntawm lub qhov dej yog feem ntau tsis pub tsawg tshaj 3 meters (saib daim duab 2).
5. Qhov dej nkag qhov tob ntawm lub twj tso kua mis dej yuav tsum tsis pub tsawg tshaj 1-1.5 meters los ntawm cov dej dynamic mus rau qhov dej nkag ntawm qhov dej (saib daim duab 2). Txwv tsis pub, cov dej twj tso kua mis bearings yuav yooj yim puas.
6. Lub nqa ntawm lub twj tso kua dej tsis tuaj yeem qis dhau. Txwv tsis pub, lub rooj vag valve yuav tsum tau muab tso rau ntawm lub qhov dej hauv qhov dej los tswj lub twj tso kua mis ntawm qhov ntsuas qhov taw tes kom tsis txhob muaj lub cev muaj zog los ntawm overloaded thiab hlawv tawm vim qhov txaus txaus.
7. Thaum lub twj tso kua dej ua haujlwm, cov dej tso tawm yuav tsum tsis tu ncua thiab txawm tias, qhov tam sim no yuav tsum ruaj khov (raws li kev ntsuas kev ua haujlwm, feem ntau tsis pub tshaj 10% ntawm cov ntsuas tam sim no), thiab yuav tsum tsis muaj kev vibration lossis suab nrov. Yog tias muaj qhov txawv txav, lub tshuab yuav tsum tau nres kom paub qhov ua rau thiab tshem tawm nws.
8. Thaum txhim kho, xyuam xim rau qhov chaw ntawm lub cev muaj zog grounding hlau (saib daim duab 2). Thaum cov yeeb nkab dej yog cov yeeb nkab steel, coj nws los ntawm lub qhov dej zoo clamp; thaum cov yeeb nkab dej yog cov yeeb nkab yas, coj nws los ntawm cov cim hauv av ntawm lub tshuab hluav taws xob.

• 1.After installing the submersible pump, recheck the insulation resistance and the three-phase continuity at the switch, and check whether there are errors in the connection of the instrument and the starting equipment.If there are no problems, you can start to test the machine. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump emits any noise or vibration. If everything is normal, it can be put into operation.
• 2. After the pump runs for the first four hours, the thermal insulation resistance of the motor should be closed and tested quickly.Its value should not be less than 0.5 megaohm.After the pump stops, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing and burning the motor due to excessive current.
• 3. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to troubleshoot.
•  
• 1 Hauv kev ntsuas kev ua haujlwm, qhov tam sim no tshaj 20%.
• 2 Lub dynamic dej theem poob mus rau hauv cov dej inlet seem, ua rau cov dej tsis sib xws.
• 3 Lub twj tso kua mis submersible muaj kev vibration loj lossis suab nrov.
• 4 Cov khoom siv hluav taws xob qis dua 340 volts.
• 5 Ib lub fuse raug hlawv.
• 6 Lub raj xa dej puas lawm.
• 7 Lub cev muaj zog lub rwb thaiv tsev tsis kam rau lub xeev geothermal yog qis dua 0.5 megaohm.
•  
• Unit disassembly:
• 1.untie cable rope, remove the pipeline part, remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the inlet junction with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) inlet junction, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising of the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the reverse order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product adopts advanced design and provides advanced storage suggestions to ensure long-term use effect.First of all, in winter, it is necessary to exhaust all the water to prevent freezing. In addition, the wire rolls should be placed well and tied up.Secondly, when storing, the environment without corrosive action and gas should be selected and the temperature should be kept below 40 °C. Finally, when not used for a long time, attention should be paid to prevent rust of submersible pump.These storage requirements will ensure that the product can maintain its performance status and prolong its service life for a long time.

01 Lub qhov dej tob tob

02 High-rise water supply

03 roob dej 

04 dej

05 Agricultural irrigation

06 vaj irrigation

07 dej haus

08 dej hauv tsev