125QJR iMpompa eNgantywiliselwa nzulu

Suitable for underground hot water mining with water temperature below 100°C, with heat resistance, corrosion resistance, aging resistance and other characteristics

This product is a powerful three-phase AC 380V (tolerance ± 5%), 50HZ (tolerance ± 1%) electric pump, suitable for all kinds of occasions need high-power pump. Its design considers a variety of water quality factors, including water temperature not higher than 20 °C, solid impurities content is not greater than 0.01%, PH value is 6.5-8.5, hydrogen sulfide content is not greater than 1.5mg/L, chloride ion content is not greater than 400mg/L, etc. The product adopts a closed or water immersion wet structure of the motor, before use in the submersible motor chamber filled with clean water to prevent empty fill. Requirements in strict accordance with the requirements of the matching cable and equipped with external overload protection device. To ensure stable operation, the submersible pump must be completely immersed in water operation, the insertion depth shall not exceed 70 meters, and the distance from the bottom of the well shall not be less than 3 meters. In addition, the pump shall not be a no-load test before start. In general, this product has the characteristics of high efficiency and stability, suitable for a variety of pump tasks in harsh environment.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, strictly according to the provisions of the pump lift, flow range of use, to prevent low flow or high lift pumping force, the thrust bearing and other parts of the wear, the motor overload burned 6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the water in the motor cavity, prevent the motor cavity water ice damage caused by low temperature.

The pump parts are mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The motor is a water-filled submersible three-phase asynchronous motor, which is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the difference in internal water expansion and contraction pressure caused by the temperature rise of the motor. In order to prevent the sand in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft is connected with the motor shaft through a coupling, and a thrust bearing is installed at the lower part of the motor. The lubrication of the motor and the pump bearing is water lubrication. The stator winding of the motor adopts high quality submersible motor winding wire, with high insulation performance. The pump adopts computer CAD design, with simple structure and excellent technical performance.

(1)Ulungiselelo phambi kofakelo:
1. Jonga ukuba impompo engaphantsi kwamanzi iyahlangabezana nemiqathango yokusetyenziswa kunye nobubanzi obuchazwe kwincwadana.
2. Ukusebenzisa i-obiect enzima ene-diameter elingana nobukhulu obungaphandle bedayamitha yempompo engaphantsi kwamanzi, linganisa ukuba i-inneldiameter ye-wellbore ingafanelana nempompo engaphantsi kwamanzi, kwaye ulinganise ukuba ubunzulu bomthombo buhlangabezana neemfuno zokufakela.
3. Jonga ukuba iqula licocekile na kunye nokuba amanzi amgxobhozo na. Ungaze usebenzise impompo yombane engaphantsi kwamanzi ukuhlamba udaka lwempompo ye-welor kunye namanzi esanti ukunqanda umonakalo ophambi kwexesha kwimpompo yombane engaphantsi kwamanzi.
4. Khangela ukuba indawo ye-welhead yokufakela i-clamp ifanelekile kwaye ingaba inokumelana nomgangatho weyunithi yonke.
5. Khangela ukuba izixhobo zempompo eziphantsi kwamanzi zigqityiwe kwaye zifakwe ngokufanelekileyo ngokwedayagram yendibano kwincwadana Susa isikrini sokucoca kwaye ujikelezise ukudibanisa ukuze ubone ukuba ijikeleza ngokuguquguqukayo.
6. Khupha isikrufu samanzi uze ugcwalise umngxuma wemoto ngamanzi acocekileyo, angadlekiyo (qaphela. qiniseka ukuba uyasifafa), uze uqinise isikrufu samanzi. Emva kweeyure ezili-12 zenaliti yamanzi, ukuxhathisa kwe-insulation ye-motor akufanele kube ngaphantsi kwe-150M Q xa kulinganiswa netafile yokungcangcazela ye-500V.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Umzobo oqhotyoshelweyo wenkqubo yokufaka iintambo zentambo umi ngolu hlobo lulandelayo:

8. Sebenzisa i-multimeter ukujonga ukuba ngaba iingcingo zesigaba sesithathu zidibaniswe kunye nokuba ukuchasana kwe-DC kuphantse kulinganiswe.
9. Khangela ukuba isekethe kunye nomthamo we-transformer ugcwele kakhulu, kwaye emva koko uqhagamshele i-switch yokukhusela okanye uqalise izixhobo. Jonga iTheyibhile yesi-2 kwiimodeli ezithile, kwaye emva koko galela ibhakethi lamanzi kwimpompo yamanzi ukusuka kwindawo yokupompoza amanzi ukuthambisa iibheringi zerabha kwimpompo, kwaye emva koko ubeke impompo yombane entywilayo ngokuthe tye kwaye izinzile.Qala (ungabi ngaphezu komzuzwana omnye) kwaye ujonge ukuba ngaba ulwalathiso lokuqhuba luyahambelana nophawu lokuqhuba. Ukuba akunjalo, tshintsha naziphi na izihlanganisi ezibini zesigaba sesithathu sentambo. Emva koko faka isihluzo kwaye ulungiselele ukuhla equleni. Ukuba isetyenziswe ngezihlandlo ezikhethekileyo (ezifana nemijelo, imisele, imilambo, amachibi, amachibi, njl. njl.), impompo yombane kufuneka isekelwe ngokuthembekileyo.

(2)Izixhobo zofakelo kunye nezixhobo:
1. Ipere enye yamatyathanga okuphakamisa ngaphezulu kweetoni ezimbini.
2. I-tripod enobude obuthe nkqo obungekho ngaphantsi kweemitha ezine.
3. Iintambo ezimbini ezijingayo (iintambo zocingo) ezinokuthwala ubunzima obungaphezu kwetoni enye (zinokuthwala ubunzima beseti epheleleyo yeempompo zamanzi).
4. Fakela izibini ezimbini zeeclamps (i-splints).
5. Izitshixo, izando, i-screwdrivers, izixhobo zombane kunye nezixhobo, njl.

(3)Ufakelo lwempompo yombane:
1. Umzobo wofakelo lwempompo yombane engaphantsi kwamanzi iboniswe kuMzobo 2. Imilinganiselo ethile yokufakela iboniswe kwiThebhile 3 "Uluhlu lweMilinganiselo yokuFakela iPump yoMbane ongaphantsi kwamanzi".

2. Iimpompo zombane ezingaphantsi kwamanzi ezinentloko engaphantsi kweemitha ezingama-30 zinokunyuswa ngokuthe ngqo equleni kusetyenziswa imibhobho kunye neentambo zocingo okanye ezinye iintambo zehemp ezinokuthwala ubunzima obupheleleyo bomatshini wonke, imibhobho yamanzi, kunye namanzi kwimibhobho.

3. Iipompo ezinentloko yeemitha ezingaphezu kwe-30 zisebenzisa iipayipi zensimbi, kwaye ulandelelwano lofakelo lulandelayo:
①Sebenzisa ibamba ukucinezela isiphelo esiphezulu sempompo yamanzi (injini kunye nempompo yamanzi sele idityanisiwe ngeli xesha), yiphakamise ngetsheyini ejingayo, kwaye uyibophe ngokukhawuleza equleni de ubeke isibambiso entloko kwaye uyisuse. ikhonkco elijingayo.
② Sebenzisa enye ipere yeziqhoboshi ukuqhobosha umbhobho, uwuphakamise ngetyathanga elijingayo 15 cm kude neflange, kwaye uwuhlise kancinane. Phakathi kweflange yombhobho kunye neflange yepompoFaka ipadi yerabha endaweni kwaye uqinise umbhobho kwaye umpompe ngokulinganayo ngeebholiti, iinati kunye newasher zasentwasahlobo.
③ Phakamisa kancinane impompo entywilayo emanzini, susa isithinteli esikwisiphelo esiphezulu sempompo yamanzi, qhina intambo ngokuqinileyo kumbhobho wamanzi ngeteyiphu yeplastiki, kwaye uyibophe kancinane de Ibamba libekwe emthonjeni.
④Sebenzisa indlela efanayo ukubopha yonke imibhobho yamanzi equleni.
⑤Emva kokuba ikhebula elikhokelayo liqhagamshelwe kwisitshixo solawulo, liqhagamshelwe kunikezelo lwamandla amanqanaba amathathu.

(4)Izinto ekufuneka uziqwalasele ngexesha lofakelo:
1. Ukuba i-jamming phenomenon ifunyenwe ngexesha lenkqubo yokupompa, jika okanye utsale umbhobho wamanzi ukuze unqobe i-jamming point. Ukuba imilinganiselo eyahlukeneyo ayisebenzi, nceda unganyanzeli impompo phantsi ukunqanda umonakalo kwimpompo yombane engaphantsi kwamanzi kunye nequla.
2. Ngethuba lofakelo, i-rubber pad kufuneka ifakwe kwi-flange yombhobho ngamnye kwaye iqiniswe ngokulinganayo.
3. Xa impompo yamanzi ithotywa equleni, kufuneka ibekwe embindini wombhobho wequla ukuthintela ukuba impompo ihambe ngaphaya kodonga lwequla ixesha elide, nto leyo ebangela ukuba impompo ingcangcazele kwaye imotor itshayele kwaye itshise. .
4. Qinisekisa ubunzulu bempompo yamanzi ukuya ezantsi kwequla ngokwesanti equkuqelayo kunye neemeko zentlenge equleni. Musa ukungcwaba impompo eludakeni. Umgama ukusuka kumpompo wamanzi ukuya ezantsi kwequla awukho ngaphantsi kweemitha ezi-3 (jonga umfanekiso 2).
5. Ubunzulu bokungena kwamanzi kwimpompo yamanzi kufuneka bungabi ngaphantsi kwe-1-1.5 yeemitha ukusuka kwinqanaba lamanzi aguquguqukayo ukuya kwindawo yokungena kwamanzi (jonga uMfanekiso 2). Ngaphandle koko, iibheringi zempompo zamanzi zinokonakala lula.
6. Ukunyuswa kwempompo yamanzi akunakuba phantsi kakhulu. Kungenjalo, ivalve yesango kufuneka ifakwe kumbhobho wamanzi osentloko yomthombo ukulawula ukuhamba kwempompo kwindawo yokuqukuqela ehleliweyo ukuthintela ukugcwala okugqithisileyo kwemoto kwaye itshiswe ngenxa yamazinga amakhulu okuhamba.
7. Xa umpompo wamanzi usebenza, ukukhutshwa kwamanzi kufuneka kuqhubeke kwaye nokuba, okwangoku kufuneka kuzinzile (phantsi kweemeko zokusebenza ezilinganisiweyo, ngokuqhelekileyo akukho ngaphezu kwe-10% ye-current rated current), kwaye akufanele kubekho ukungcangcazela okanye ingxolo. Ukuba kukho nakuphi na ukungaqhelekanga, umatshini kufuneka umiswe ukufumanisa unobangela kwaye upheliswe.
8. Xa ufaka, qwa lasela ukusetwa kwe-motor grounding wire (jonga umfanekiso 2). Xa umbhobho wamanzi ungumbhobho wentsimbi, yiholele kwi-clamp ye-wellhead clamp; xa umbhobho wamanzi ungumbhobho weplastiki, ukhokele ukusuka kwindawo yokubeka ipompo yombane.

• （1）With the continuous development of modern technology, submersible pumps play a crucial role in the field of pumps. After installing the submersible pump, check the insulation resistance and three-phase continuity repeatedly to ensure that there are no errors in the connection between the instrument and the starting equipment. If everything is normal, the test equipment can be started. After starting, observe whether the indication readings of each instrument are correct. If the rated voltage and current specified on the nameplate are exceeded, pay attention to observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. After the pump runs for four hours for the first time, it should be closed and the thermal insulation resistance of the motor should be tested quickly, and its value should not be less than 0.5 megaohms. After stopping the pump, restart it after five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to overcurrent. After the pump is running normally, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the equipment should be shut down immediately to troubleshoot. The current exceeds 20% under the rated working conditions; the dynamic water level drops to the inlet section, resulting in intermittent drainage; the submersible pump vibrates violently or makes noisy sounds; the supply voltage is lower than 340 volts; any fuse is broken; the water pipe is damaged; The thermal insulation resistance between the motor and the ground is less than 0.5 megaohm.These recommended operating procedures and safety measures ensure the safe operation of the submersible pump, prolong the service life of the equipment, and provide users with a reliable pump choice.
•  
• （2）Unit disassembly:
• 1 untie the cable tie, remove the pipeline part, remove the wire plate.
• 2 unscrew the water release bolt, put the water in the motor chamber.
• 3 remove the filter, loose the fixing screw of the motor shaft on the coupling.
• 4 unscrew the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5 the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending the pump shaft and various bumps in the disassembly process.
• 6 the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nut, base, shaft head lock nut, thrust plate, key, lower guide bearing seat, double head bolt from the bottom of the motor in turn. Then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7 unit assembly: Before assembly, the rust and dirt of the parts should be cleaned, and the mating surfaces and fasteners should be coated with sealant. Then they should be assembled in the reverse order of disassembly (the up and down momentum of the motor shaft is about 1 mm after assembly). After assembly, the coupling should be flexible, and then the filter screen test machine.
•  
• （3）The submersible pump should be dismantled and repaired according to Article 5 for each operation year, or less than one year, but the submersible time has reached two years, and the worn parts should be replaced.

 1, khupha amanzi kwi-motor cavity (ingakumbi ebusika ukukhusela i-motor ekukhenkceni), kwaye ubophe intambo kakuhle.

 2, store in an indoor room without corrosive substances and gases, with a temperature below 40 °C.

 I-3, ukusetyenziswa kwexesha elide kufuneka kuhlawule ingqalelo ekuthinteleni umhlwa kweempompo ezingaphantsi kwamanzi.

01 Ukusela amanzi kwiqula elinzulu

02 Ubonelelo lwamanzi olukwizinga eliphezulu

03 unikezelo lwamanzi entabeni 

04 amanzi enqaba

05 Ukunkcenkceshela kwezolimo

06 ukunkcenkceshela egadini

07 amanzi omlambo

08 amanzi asekhaya