175QJR iMpompa eNgantywiliselwa nzulu

This product is designed for underground hot water mining and is suitable for water temperatures below 100°C. It has high temperature resistance, corrosion resistance and aging resistance. This product is very suitable for use in underground hot water mining environments, which can effectively deal with high temperatures and corrosion of various chemical substances, while having good aging resistance, ensuring stable operation of equipment for a long time. Whether it is needed to be used in harsh mining environments or in the face of high water temperatures, this product can provide reliable protection, ensuring continuous operation and efficient work of equipment.

 Product introduction: we recommend this product is equipped with three-phase AC 380V (tolerance + / - 1%), 50HZ (tolerance + / - 1%) power supply. Water quality requirements are strict, the water temperature shall not be higher than 20 °C, the content of solid impurities (mass ratio) shall not be greater than 0.01%; PH value (pH) between 6.5-8.5; hydrogen sulfide content shall not be greater than 1.5mg/L; chloride ion content shall not exceed 400mg/L. The product is equipped with a closed or water-cooled wet structure motor. Before use, the inner cavity of the submersible motor shall be filled with clean water to prevent empty. Then tighten the water injection and air exhaust screws, otherwise it is prohibited to use. The submersible pump must be completely immersed in water to operate, the penetration depth shall not exceed 70 meters, and the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The inflow of well water shall meet the water output and continuous operation requirements of the submersible pump, and the water output of the pump shall be controlled between 0.7 and 1.2 times the rated flow. The well must be vertical, and the submersible pump can not be used horizontally or dumped, but only vertically. The submersible pump must be equipped with cables as required, and is equipped with external overload protection device. It is prohibited to test the pump without water and no load.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, ngokungqongqo ngokwemiqathango yokunyuswa kwempompo, uluhlu lokuhamba kokusetyenziswa, ukuthintela ukuhamba okuphantsi okanye amandla okumpompa aphezulu, ukunyanzeliswa kwe-thrust kunye nezinye iindawo zokunxiba, ukugcwala kwemoto kutshiswe.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Intshayelelo emfutshane yolwakhiwo: inxalenye yempompo yenziwe ikakhulu yimpompo yempompo, i-impeller, igobolondo le-diversion, i-rubber bearing, i-valve yokukhangela umzimba (indawo ezikhethiweyo) kunye nezinye izinto. , isihlalo esisezantsi esiphethe isikhokelo, i-stator, i-rotor, isihlalo esiphezulu sokuhamba kwesikhokelo, isanti yesanti, icandelo lokungena kwamanzi, ikhebula kunye nezinye izinto.

Iimpawu eziphambili zemveliso ziquka:

 I-1, i-motor ngamanzi azaliswe ngamanzi angaphantsi kwamanzi amanqanaba amathathu e-asynchronous motor, i-motor cavity igcwele amanzi acocekileyo, isetyenziselwa ukupholisa i-motor kunye nokuthambisa i-bearing, ifilimu elawula uxinzelelo ezantsi kwe-motor isetyenziselwa ukulungelelanisa. Ukwandiswa kunye nokwahlukana koxinzelelo loxinzelelo lwamanzi ngaphakathi emzimbeni obangelwa utshintsho lokunyuka kobushushu bemoto.

 I-2, Ukuthintela isanti kumanzi omthombo ekungeneni kwi-motor, isiphelo esiphezulu se-motor shaft sixhotywe ngamatywina amabini e-oyile, kunye nendandatho yesanti ifakwe ukwenza isakhiwo sokukhusela isanti.

 I-3, Ukuze uthintele i-shaft yepompo ukuba iqhube xa iqala, i-pump shaft kunye ne-motor shaft idibaniswe ngokudibanisa, kwaye i-top thrust bear ifakwe kwindawo engezantsi yemoto.

 I-4, I-lubrication ye-motor kunye ne-pump ephethe i-lubrication yamanzi.

 I-5, i-motor stator winding yenziwe nge-high-submersible motor winding wire, kunye nokusebenza okuphezulu kwe-insulation.

 I-6, ipompo yenzelwe i-CAD yekhompyutheni, kunye nesakhiwo esilula kunye nokusebenza kakuhle kwezobugcisa.

(1)Ulungiselelo phambi kofakelo:
1. Jonga ukuba impompo engaphantsi kwamanzi iyahlangabezana nemiqathango yokusetyenziswa kunye nobubanzi obuchazwe kwincwadana.
2. Ukusebenzisa i-obiect enzima ene-diameter elingana nobukhulu obungaphandle bedayamitha yempompo engaphantsi kwamanzi, linganisa ukuba i-inneldiameter ye-wellbore ingafanelana nempompo engaphantsi kwamanzi, kwaye ulinganise ukuba ubunzulu bomthombo buhlangabezana neemfuno zokufakela.
3. Jonga ukuba iqula licocekile na kunye nokuba amanzi amgxobhozo na. Ungaze usebenzise impompo yombane engaphantsi kwamanzi ukuhlamba udaka lwempompo ye-welor kunye namanzi esanti ukunqanda umonakalo ophambi kwexesha kwimpompo yombane engaphantsi kwamanzi.
4. Khangela ukuba indawo ye-welhead yokufakela i-clamp ifanelekile kwaye ingaba inokumelana nomgangatho weyunithi yonke.
5. Khangela ukuba izixhobo zempompo eziphantsi kwamanzi zigqityiwe kwaye zifakwe ngokufanelekileyo ngokwedayagram yendibano kwincwadana Susa isikrini sokucoca kwaye ujikelezise ukudibanisa ukuze ubone ukuba ijikeleza ngokuguquguqukayo.
6. Khupha isikrufu samanzi uze ugcwalise umngxuma wemoto ngamanzi acocekileyo, angadlekiyo (qaphela. qiniseka ukuba uyasifafa), uze uqinise isikrufu samanzi. Emva kweeyure ezili-12 zenaliti yamanzi, ukuxhathisa kwe-insulation ye-motor akufanele kube ngaphantsi kwe-150M Q xa kulinganiswa netafile yokungcangcazela ye-500V.
7. Umdibaniso wekheyibhile, unqumle umkhono werabha oyi-120mm kwelinye icala lentambo ephumayo kunye nentambo yokumatanisa enemela yomntu wombane uze ugxadazele ubude beengcingo ezintathu ezingundoqo ngendlela enyathelweyo, krazula umbindi wobhedu oyi-20mm, krazula ioksidi. umaleko ongaphandle kocingo lobhedu ngemela okanye ngelaphu lesanti, kwaye ufake iziphelo zocingo ezimbini eziqhagamshelweyo kwi palirs.Emva kokubopha umaleko ngokuqinileyo ngocingo olucolekileyo lobhedu, i-solder ngokucokisekileyo kwaye ngokuqinileyo, kunye nesanti yayo nayiphi na. amaqhuma phezu komhlaba. Emva koko, kumalungu amathathu, sebenzisa iteyiphu yokugquma i-polyvester ukuyisonga ngendlela epakishwe kabini kwizitya zokuhlambela ezintathu. Songa iziphelo ezibini zomaleko wokusonga ngokuqinileyo ngomsonto we-nyion, kwaye emva koko usebenzise indlela epakishwe kabini ukusonga iteyiphu kwiileya ezintathu. Songa i-outellayer ngetape yoxinzelelo oluphezulu lwe-insulation kwimigangatho emithathu. Ekugqibeleni, phinda udibanise imisonto emithathu kwaye uyibophe ngokuphindaphindiweyo kwi-fivelayers nge-tape yoxinzelelo oluphezulu. Umaleko ngamnye kufuneka ubotshelelwe ngokuqinileyo, kwaye amalungu e-interlayer kufuneka abe ngqongqo kwaye abe fimm ukukhusela amanzi ukuba angangeni kwaye wonakalise isigqubuthelo, Emva kokusonga, faka amanzi kwindawo yobushushu obungama-20 'c iiyure ezili-12, kwaye ulinganise ukuxhathisa ukugquma ngetafile eshukumayo. , ekufuneka ingabi ngaphantsi kwe-100M Ω

Umzobo oqhotyoshelweyo wenkqubo yokufaka iintambo zentambo umi ngolu hlobo lulandelayo:

8. Sebenzisa i-multimeter ukujonga ukuba ngaba iingcingo zesigaba sesithathu zidibaniswe kunye nokuba ukuchasana kwe-DC kuphantse kulinganiswe.
9. Khangela ukuba isekethe kunye nomthamo we-transformer ugcwele kakhulu, kwaye emva koko uqhagamshele i-switch yokukhusela okanye uqalise izixhobo. Jonga iTheyibhile yesi-2 kwiimodeli ezithile, kwaye emva koko galela ibhakethi lamanzi kwimpompo yamanzi ukusuka kwindawo yokupompoza amanzi ukuthambisa iibheringi zerabha kwimpompo, kwaye emva koko ubeke impompo yombane entywilayo ngokuthe tye kwaye izinzile.Qala (ungabi ngaphezu komzuzwana omnye) kwaye ujonge ukuba ngaba ulwalathiso lokuqhuba luyahambelana nophawu lokuqhuba. Ukuba akunjalo, tshintsha naziphi na izihlanganisi ezibini zesigaba sesithathu sentambo. Emva koko faka isihluzo kwaye ulungiselele ukuhla equleni. Ukuba isetyenziswe ngezihlandlo ezikhethekileyo (ezifana nemijelo, imisele, imilambo, amachibi, amachibi, njl. njl.), impompo yombane kufuneka isekelwe ngokuthembekileyo.

(2)Izixhobo zofakelo kunye nezixhobo:
1. Ipere enye yamatyathanga okuphakamisa ngaphezulu kweetoni ezimbini.
2. I-tripod enobude obuthe nkqo obungekho ngaphantsi kweemitha ezine.
3. Iintambo ezimbini ezijingayo (iintambo zocingo) ezinokuthwala ubunzima obungaphezu kwetoni enye (zinokuthwala ubunzima beseti epheleleyo yeempompo zamanzi).
4. Fakela izibini ezimbini zeeclamps (i-splints).
5. Izitshixo, izando, i-screwdrivers, izixhobo zombane kunye nezixhobo, njl.

(3)Ufakelo lwempompo yombane:
1. Umzobo wofakelo lwempompo yombane engaphantsi kwamanzi iboniswe kuMzobo 2. Imilinganiselo ethile yokufakela iboniswe kwiThebhile 3 "Uluhlu lweMilinganiselo yokuFakela iPump yoMbane ongaphantsi kwamanzi".

2. Iimpompo zombane ezingaphantsi kwamanzi ezinentloko engaphantsi kweemitha ezingama-30 zinokunyuswa ngokuthe ngqo equleni kusetyenziswa imibhobho kunye neentambo zocingo okanye ezinye iintambo zehemp ezinokuthwala ubunzima obupheleleyo bomatshini wonke, imibhobho yamanzi, kunye namanzi kwimibhobho.

3. Iipompo ezinentloko yeemitha ezingaphezu kwe-30 zisebenzisa iipayipi zensimbi, kwaye ulandelelwano lofakelo lulandelayo:
①Sebenzisa ibamba ukucinezela isiphelo esiphezulu sempompo yamanzi (injini kunye nempompo yamanzi sele idityanisiwe ngeli xesha), yiphakamise ngetsheyini ejingayo, kwaye uyibophe ngokukhawuleza equleni de ubeke isibambiso entloko kwaye uyisuse. ikhonkco elijingayo.
② Sebenzisa enye ipere yeziqhoboshi ukuqhobosha umbhobho, uwuphakamise ngetyathanga elijingayo 15 cm kude neflange, kwaye uwuhlise kancinane. Phakathi kweflange yombhobho kunye neflange yepompoFaka ipadi yerabha endaweni kwaye uqinise umbhobho kwaye umpompe ngokulinganayo ngeebholiti, iinati kunye newasher zasentwasahlobo.
③ Phakamisa kancinane impompo entywilayo emanzini, susa isithinteli esikwisiphelo esiphezulu sempompo yamanzi, qhina intambo ngokuqinileyo kumbhobho wamanzi ngeteyiphu yeplastiki, kwaye uyibophe kancinane de Ibamba libekwe emthonjeni.
④Sebenzisa indlela efanayo ukubopha yonke imibhobho yamanzi equleni.
⑤Emva kokuba ikhebula elikhokelayo liqhagamshelwe kwisitshixo solawulo, liqhagamshelwe kunikezelo lwamandla amanqanaba amathathu.

(4)Izinto ekufuneka uziqwalasele ngexesha lofakelo:
1. Ukuba i-jamming phenomenon ifunyenwe ngexesha lenkqubo yokupompa, jika okanye utsale umbhobho wamanzi ukuze unqobe i-jamming point. Ukuba imilinganiselo eyahlukeneyo ayisebenzi, nceda unganyanzeli impompo phantsi ukunqanda umonakalo kwimpompo yombane engaphantsi kwamanzi kunye nequla.
2. Ngethuba lofakelo, i-rubber pad kufuneka ifakwe kwi-flange yombhobho ngamnye kwaye iqiniswe ngokulinganayo.
3. Xa impompo yamanzi ithotywa equleni, kufuneka ibekwe embindini wombhobho wequla ukuthintela ukuba impompo ihambe ngaphaya kodonga lwequla ixesha elide, nto leyo ebangela ukuba impompo ingcangcazele kwaye imotor itshayele kwaye itshise. .
4. Qinisekisa ubunzulu bempompo yamanzi ukuya ezantsi kwequla ngokwesanti equkuqelayo kunye neemeko zentlenge equleni. Musa ukungcwaba impompo eludakeni. Umgama ukusuka kumpompo wamanzi ukuya ezantsi kwequla awukho ngaphantsi kweemitha ezi-3 (jonga umfanekiso 2).
5. Ubunzulu bokungena kwamanzi kwimpompo yamanzi kufuneka bungabi ngaphantsi kwe-1-1.5 yeemitha ukusuka kwinqanaba lamanzi aguquguqukayo ukuya kwindawo yokungena kwamanzi (jonga uMfanekiso 2). Ngaphandle koko, iibheringi zempompo zamanzi zinokonakala lula.
6. Ukunyuswa kwempompo yamanzi akunakuba phantsi kakhulu. Kungenjalo, ivalve yesango kufuneka ifakwe kumbhobho wamanzi osentloko yomthombo ukulawula ukuhamba kwempompo kwindawo yokuqukuqela ehleliweyo ukuthintela ukugcwala okugqithisileyo kwemoto kwaye itshiswe ngenxa yamazinga amakhulu okuhamba.
7. Xa umpompo wamanzi usebenza, ukukhutshwa kwamanzi kufuneka kuqhubeke kwaye nokuba, okwangoku kufuneka kuzinzile (phantsi kweemeko zokusebenza ezilinganisiweyo, ngokuqhelekileyo akukho ngaphezu kwe-10% ye-current rated current), kwaye akufanele kubekho ukungcangcazela okanye ingxolo. Ukuba kukho nakuphi na ukungaqhelekanga, umatshini kufuneka umiswe ukufumanisa unobangela kwaye upheliswe.
8. Xa ufaka, qwa lasela ukusetwa kwe-motor grounding wire (jonga umfanekiso 2). Xa umbhobho wamanzi ungumbhobho wentsimbi, yiholele kwi-clamp ye-wellhead clamp; xa umbhobho wamanzi ungumbhobho weplastiki, ukhokele ukusuka kwindawo yokubeka ipompo yombane.

1. 1.After the submersible pump is installed, check the insulation resistance and three-phase conduction from the switch again, check whether the instrument and the connection of the start equipment are wrong, if there is no problem, the trial machine can be started, and observe whether the indicator readings of the instrument exceed the rated voltage and current specified on the nameplate after the start, and observe whether the pump has noise and vibration phenomenon. If everything is normal, it can be put into operation.
2. 2. After the first operation of the pump for four hours, the motor should be shut down to test the thermal insulation resistance quickly, and its value should not be less than 0.5 megaohm.
3. 3. After the pump is shut down, it should be started after five minutes to prevent the water column in the pipe from burning due to excessive motor current.
4. 4. After the pump is running normally, in order to prolong its service life, it is necessary to check whether the power supply voltage, running current and insulation resistance are normal on a regular basis.If the following conditions are found, the equipment should be shut down immediately to eliminate the fault:
5. - Under the rated working conditions, the current exceeds 20%.
6. - The dynamic water level drops to the inlet section, resulting in intermittent drainage.
7. - The submersible pump vibrates violently or emits noisy sounds.
8. - The power supply voltage is lower than 340 volts.
9. - There is a phase blown out in the fuse.
10. - The water pipe is damaged.
11. - The thermal insulation resistance between the motor and the ground is less than 0.5 megaohm.

1. 5. Disassembly device:
2. - Untie the cable, take off the pipe part and remove the line protection plate.
3. - Unscrew the drain screw and exclude all water in the motor chamber.
4. - Take out the filter and loosen the fixing screw on the coupling fixed to the motor shaft.
5. - Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to the level of the device to prevent the bending of the pump shaft when separating).
6. - The disassembly sequence of the pump is as follows: (see Figure 1) water inlet section, impeller, shunt shell, impeller, check valve body. When removing the impeller, use special tools to loosen the cone sleeve fixed to the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various parts.
7. - The disassembly process of the motor is as follows: (see Figure 1) place the motor on the platform, and remove the nuts, base, shaft head lock nut, thrust plate, key, lower guide bearing. seat, and tie rod bolts from the bottom of the motor in order (see Figure 1), and then take out the rotor (be careful not to damage the wiring harness) and finally take out the connector and upper guide bearing seat.
8. - Assembly unit: before assembly, all parts should be cleaned of rust and dirt, and smear sealant on all the surfaces and fasteners, and then assemble in the opposite order of disassembly (the movement of the motor shaft after assembly is about 1 mm). After assembly, the coupling should be flexible, and then wear the filter for machine test. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 1, khupha amanzi kwi-motor cavity (ingakumbi ebusika ukukhusela i-motor ekukhenkceni), kwaye ubophe intambo kakuhle.

 2, gcina kwigumbi elingaphakathi elingenazo izinto ezonakalisayo kunye neegesi, ezinobushushu obungaphantsi kwama-40 °C.

 I-3, ukusetyenziswa kwexesha elide kufuneka kuhlawule ingqalelo ekuthinteleni umhlwa kweempompo ezingaphantsi kwamanzi.

01 Ukusela amanzi kwiqula elinzulu

02 Ubonelelo lwamanzi olukwizinga eliphezulu

03 unikezelo lwamanzi entabeni 

04 amanzi enqaba

05 Ukunkcenkceshela kwezolimo

06 ukunkcenkceshela egadini

07 amanzi omlambo

08 amanzi asekhaya