175QJR Iphampu Ejulile Ngaphansi Kwamanzi

This product is designed for underground hot water mining and is suitable for water temperatures below 100°C. It has high temperature resistance, corrosion resistance and aging resistance. This product is very suitable for use in underground hot water mining environments, which can effectively deal with high temperatures and corrosion of various chemical substances, while having good aging resistance, ensuring stable operation of equipment for a long time. Whether it is needed to be used in harsh mining environments or in the face of high water temperatures, this product can provide reliable protection, ensuring continuous operation and efficient work of equipment.

 Product introduction: we recommend this product is equipped with three-phase AC 380V (tolerance + / - 1%), 50HZ (tolerance + / - 1%) power supply. Water quality requirements are strict, the water temperature shall not be higher than 20 °C, the content of solid impurities (mass ratio) shall not be greater than 0.01%; PH value (pH) between 6.5-8.5; hydrogen sulfide content shall not be greater than 1.5mg/L; chloride ion content shall not exceed 400mg/L. The product is equipped with a closed or water-cooled wet structure motor. Before use, the inner cavity of the submersible motor shall be filled with clean water to prevent empty. Then tighten the water injection and air exhaust screws, otherwise it is prohibited to use. The submersible pump must be completely immersed in water to operate, the penetration depth shall not exceed 70 meters, and the distance between the bottom of the submersible pump and the bottom of the well shall not be less than 3 meters. The inflow of well water shall meet the water output and continuous operation requirements of the submersible pump, and the water output of the pump shall be controlled between 0.7 and 1.2 times the rated flow. The well must be vertical, and the submersible pump can not be used horizontally or dumped, but only vertically. The submersible pump must be equipped with cables as required, and is equipped with external overload protection device. It is prohibited to test the pump without water and no load.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, ngokuqinile ngokwezinhlinzeko zokuphakanyiswa kwepompo, ububanzi bokugeleza bokusetshenziswa, ukuvimbela ukugeleza okuphansi noma amandla okumpompa aphakeme kakhulu, i-thrust bear nezinye izingxenye zokugqokwa, ukugcwala kwemoto kushisiwe.

6, after the pump down the well, the measurement of the motor to the ground insulation resistance should not be less than 100M, after the start to observe the voltage and current, check the motor winding insulation, whether in line with the requirements; pump storage location temperature if less than freezing point, should be dry the motor cavity water, prevent the motor cavity water ice damage caused by low temperature.

Isethulo esifushane sesakhiwo: ingxenye yepompo yakhiwe ikakhulukazi i-pump shaft, i-impeller, igobolondo lokuphambukisa, i-rubber bear, hlola umzimba we-valve (izingxenye ozikhethela) nezinye izingxenye. , isihlalo esiphethe umhlahlandlela ophansi, i-stator, i-rotor, isihlalo esiphezulu somhlahlandlela, indandatho yesihlabathi, ingxenye yokungena kwamanzi, ikhebula nezinye izingxenye.

Izici eziyinhloko zomkhiqizo zihlanganisa:

 I-1, I-motor iyi-motor egcwele amanzi emanzi e-submersible enezigaba ezintathu ze-asynchronous motor, i-motor cavity igcwele amanzi ahlanzekile, esetshenziselwa ukupholisa i-motor kanye nokugcoba i-bearing, ifilimu elawula ukucindezela phansi kwe-motor isetshenziselwa ukulungisa. ukunwetshwa kanye nomehluko wengcindezi yokufinyela kwamanzi ngaphakathi emzimbeni okubangelwa ukushintsha kokukhuphuka kwezinga lokushisa kwemoto.

 I-2, Ukuze uvimbele isihlabathi esisemanzini omthombo ukuthi singangeni emotweni, indawo engaphezulu ye-motor shaft ifakwe izimpawu ezimbili zamafutha, futhi indandatho yesihlabathi ifakwe ukwakha isakhiwo sokuvimbela isihlabathi.

 I-3, Ukuze uvimbele i-pump shaft ukuthi ingaqhubeki lapho iqala, i-pump shaft kanye ne-motor shaft ixhunywe ngokuhlanganisa, futhi i-top thrust bear ifakwe engxenyeni engezansi ye-motor.

 4, Ukugcotshwa kwenjini kanye nephampu ephethe ukugcotshwa kwamanzi.

 I-5, i-motor stator winding yenziwe ngocingo olusezingeni eliphezulu lwe-submersible motor winding, olusebenza kahle kakhulu.

 6, Iphampu iklanywe yi-CAD yekhompyutha, enesakhiwo esilula nokusebenza okuhle kobuchwepheshe.

(1) Ukulungiselela ngaphambi kokufakwa:
1. Hlola ukuthi ingabe iphampu engaphansi kwamanzi iyahlangabezana yini nezimo zokusetshenziswa kanye nobubanzi obushiwo kubhukwana.
2. Usebenzisa i-obiect esindayo enobubanzi obulingana nobukhulu bedayamitha yangaphandle yephampu engaphansi kwamanzi, linganisa ukuthi i-inneldiameter yomthombo ingalingana nephampu engaphansi kwamanzi, futhi ulinganise ukuthi ukujula komthombo kuyahlangabezana yini nezidingo zokufakwa.
3. Hlola ukuthi umthombo uhlanzekile yini nokuthi amanzi omthombo anodaka. Ungalokothi usebenzise iphampu kagesi engaphansi kwamanzi ukugeza udaka lwepompo le-welor namanzi esihlabathi ukuze ugweme ukulimala ngaphambi kwesikhathi kwepompo kagesi engaphansi kwamanzi.
4. Hlola ukuthi indawo ye-welhead yokufaka i-welhead ifanelekile yini nokuthi ingakwazi yini ukumelana nekhwalithi yayo yonke iyunithi.
5. Hlola ukuthi izingxenye zepompo ezingaphansi kwamanzi ziphelele yini futhi zifakwe ngendlela efanele ngokomdwebo womhlangano osebhukwini Susa isikrini sokuhlunga bese uzungezisa ukuhlanganisa ukuze ubone ukuthi siyazungeza yini
6. Khipha isikulufu samanzi bese ugcwalisa imbobo yesithuthuthu ngamanzi ahlanzekile, angagqwali (qaphela. qiniseka ukuthi uyasigcwalisa), bese uqinisa isikrufu samanzi. Ngemuva kwamahora ayi-12 omjovo wamanzi, ukumelana nokufakwa kwenjini akufanele kube ngaphansi kuka-150M Q uma kulinganiswa netafula lokunyakazisa elingu-500V.
7. Ijoyinti lekhebula, sika umkhono wenjoloba ongu-120mm ohlangothini olulodwa lwekhebula ephumayo kanye nekhebuli ehambisanayo ngommese womuntu osebenza ngogesi bese unyakazisa ubude bezintambo ezintathu eziyinhloko ngendlela enyanyisiwe, hlubula inkaba yethusi engu-20mm, klwelwe i-oxide. ungqimba olungaphandle kocingo lwethusi ngommese noma indwangu yesihlabathi, bese ufaka iziphetho zezintambo ezimbili ezixhunyiwe kuma-palirs.Ngemva kokubopha ungqimba ngokuqinile ngocingo lwethusi olucolisekileyo, luthengise kahle futhi luqine, nesihlabathi sanoma iyiphi. ama-burrs ebusweni. Bese, kumajoyinti amathathu, sebenzisa itheyiphu yokufaka i-polyvester ukuze uwasonge ngendlela enqwabelene kancane ezitsheni ezintathu. Goqa iziphetho ezimbili zongqimba olugoqayo luqine ngomucu we-nyion, bese usebenzisa indlela eyisitakikhi esincane ukusonga itheyiphu izendlalelo ezintathu. Gcoba i-outellayer nge-high-pressure insulation tape yezendlalelo ezintathu. Ekugcineni, hlanganisa imicu emithathu bese uyigoqa ngokuphindaphindiwe izendlalelo ezinhlanu nge-tape yokucindezela okuphezulu. Ungqimba ngalunye kufanele luboshwe ngokuqinile, futhi amalunga e-interlayer kufanele aqine futhi aqine ukuvimbela amanzi ukuthi angangeni futhi alimaze ukufakwa, Ngemva kokusonga, cwilisa emanzini ekamelweni lokushisa elingu-20 'c amahora angu-12, futhi ulinganise ukumelana nokushisa ngetafula elinyakazayo. , okungafanele ibe ngaphansi kuka-100M Ω

Umdwebo wenqubo yokufaka izintambo zekhebula umi kanje:

8. Sebenzisa i-multimeter ukuze uhlole ukuthi izintambo zezigaba ezintathu zixhumekile yini nokuthi ukumelana ne-DC cishe kulinganiselwe.
9. Hlola ukuthi umthamo wesekethe kanye ne-transformer ugcwele ngokweqile, bese uxhuma iswishi yokuvikela ukulayisha ngokweqile noma okokusebenza kokuqala. Bheka Ithebula 2 ukuze uthole amamodeli athile, bese uThela ibhakede lamanzi empompini yamanzi usuka endaweni yepompo yamanzi ukuze ugcobe amabheringi erabha epompo, bese ubeka iphampu kagesi engaphansi kwamanzi iqonde futhi inganyakazi.Qala (ingabi ngaphezu komzuzwana owodwa) futhi uhlole ukuthi isiqondiso sokuqondisa siyahambisana yini nophawu lokuqondisa. Uma kungenjalo, shintsha noma yiziphi izixhumi ezimbili zekhebula lezigaba ezintathu.Bese ufaka isihlungi bese ulungiselela ukwehla ngomthombo. Uma isetshenziswa ngezikhathi ezikhethekile (njengemisele, imisele, imifula, amachibi, amachibi, njll.), iphampu kagesi kufanele ibekwe phansi ngendlela enokwethenjelwa.

(2)Imishini yokufaka namathuluzi:
1. Ipheya elilodwa lamaketango okuphakamisa amathani angaphezu kwamabili.
2. I-tripod enobude obuqondile obungekho ngaphansi kwamamitha amane.
3. Izintambo ezimbili ezilengayo (izintambo zocingo) ezingathwala isisindo esingaphezu kwethani elilodwa (zingathwala isisindo sesethi ephelele yamaphampu amanzi).
4. Faka amapheya amabili ezinsimbi (ama-splint).
5. Izikele, izando, izikulufu, amathuluzi kagesi nezinsimbi, njll.

(3)Ukufakwa kwephampu kagesi:
1. Umdwebo wokufakwa kwephampu kagesi engaphansi kwamanzi uboniswa kuMfanekiso 2. Ubukhulu obuthile bokufaka buboniswa kuThebula lesi-3 "Uhlu Lobukhulu Bokufakwa Kwephampu Kagesi Engaphansi".

2. Amaphampu kagesi angaphansi kwamanzi anekhanda elingaphansi kwamamitha angu-30 angaphakanyiselwa ngqo emthonjeni kusetshenziswa amapayipi nezintambo zocingo noma ezinye izintambo ze-hemp ezingathwala isisindo esigcwele sawo wonke umshini, amapayipi amanzi, namanzi emapayipini.

3. Amaphampu anekhanda elingaphezu kwamamitha angu-30 asebenzisa amapayipi ensimbi, futhi ukulandelana kokufakwayo kungokulandelayo:
①Sebenzisa i-clamp ukuze ubambe ingxenye engenhla yengxenye yepompo yamanzi (injini nepompo yamanzi kuxhunyiwe ngalesi sikhathi), yiphakamise ngeketango elilengayo, bese uyibopha kancane kancane emthonjeni uze ufake i-clamp ekhanda lomthombo bese ukhipha iketango elilengayo.
② Sebenzisa amanye ama-clamp ukuze ubambe ipayipi, uliphakamise ngeketango elilengayo eliqhele ngamasentimitha angu-15 ukusuka ku-flange, bese ulehlisa kancane. Phakathi kwe-flange yepayipi ne-pump flangeFaka iphedi yenjoloba endaweni bese uqinisa ipayipi bese umpompa ngokulinganayo ngamabhawodi, amantongomane namawasha asentwasahlobo.
③ Phakamisa iphampu engaphansi kwamanzi kancane, khipha intambo engxenyeni engenhla yepompo yamanzi, bopha intambo ngokuqinile epayipini lamanzi ngetheyiphu yepulasitiki, bese uyibopha kancane kancane kuze kube yilapho I-clamp ibekwe emthonjeni.
④Sebenzisa indlela efanayo ukubopha wonke amapayipi amanzi emthonjeni.
⑤Ngemva kokuthi ikhebuli ephumayo ixhunywe kusiwishi sokulawula, ixhunywa ekunikezeni amandla kwezigaba ezintathu.

(4) Izinto okufanele uziqaphele ngesikhathi sokufakwa:
1. Uma i-jamming itholakala phakathi nenqubo yokumpompa, vula noma udonse ipayipi lamanzi ukuze unqobe indawo yokuma. Uma izinyathelo ezihlukahlukene zingasebenzi, sicelaUngaphoqeleli iphampu phansi ukuze ugweme ukulimala kwepompo kagesi engaphansi kwamanzi kanye nomthombo.
2. Ngesikhathi sokufakwa, i-rubber pad kufanele ibekwe ku-flange yepayipi ngayinye futhi iqiniswe ngokulinganayo.
3. Lapho iphampu yamanzi yehliselwa emthonjeni, kufanele ibekwe phakathi nepayipi lomthombo ukuze ivimbele ukuthi iphampu ingagijimi odongeni lomthombo isikhathi eside, okubangela ukuba iphampu inyakaze futhi injini ishanele futhi ishise. .
4. Thola ukujula kwepompo yamanzi ukuya phansi komthombo ngokwesihlabathi esigelezayo kanye nezimo zodaka lomthombo. Ungangcwabi iphampu odakeni. Ibanga ukusuka empompini ukuya phansi komthombo ngokuvamile alikho ngaphansi kwamamitha amathathu (bheka uMdwebo 2).
5. Ukujula kokungena kwamanzi kwephampu yamanzi kufanele kungabi ngaphansi kwamamitha angu-1-1.5 ukusuka ezingeni lamanzi aguquguqukayo kuya endaweni yokungena kwamanzi (bheka uMdwebo 2). Uma kungenjalo, ama-bearings epompo yamanzi angase alimale kalula.
6. Ukuphakanyiswa kwepompo yamanzi angeke kube phansi kakhulu. Uma kungenjalo, i-valve yesango idinga ukufakwa epayipini lamanzi elisemthonjeni ukuze kulawulwe ukugeleza kwepompo endaweni elinganiselwe yokugeleza ukuze kuvinjwe injini ukuthi ingagcwali kakhulu futhi ishiswe ngenxa yamazinga amakhulu okugeleza.
7. Lapho ipompo yamanzi isebenza, ukuphuma kwamanzi kufanele kuqhubeke futhi ngisho, okwamanje kufanele kuzinzile (ngaphansi kwezimo zokusebenza ezilinganiselwe, ngokuvamile kungabi ngaphezu kuka-10% wamanje olinganiselwe), futhi akufanele kube nokudlidliza noma umsindo. Uma kukhona okungahambi kahle, umshini kufanele umiswe ukuze kutholwe imbangela futhi kuqedwe.
8. Lapho ufaka, naka ukumiswa kocingo lwe-motor grounding wire (bheka Umfanekiso 2). Uma ipayipi lamanzi liyipayipi lensimbi, lihole kusukela ku-wellhead clamp; lapho ipayipi lamanzi liyipayipi lepulasitiki, lihole ukusuka endaweni yokubeka phansi yepompo kagesi.

1. 1.After the submersible pump is installed, check the insulation resistance and three-phase conduction from the switch again, check whether the instrument and the connection of the start equipment are wrong, if there is no problem, the trial machine can be started, and observe whether the indicator readings of the instrument exceed the rated voltage and current specified on the nameplate after the start, and observe whether the pump has noise and vibration phenomenon. If everything is normal, it can be put into operation.
2. 2. After the first operation of the pump for four hours, the motor should be shut down to test the thermal insulation resistance quickly, and its value should not be less than 0.5 megaohm.
3. 3. After the pump is shut down, it should be started after five minutes to prevent the water column in the pipe from burning due to excessive motor current.
4. 4. After the pump is running normally, in order to prolong its service life, it is necessary to check whether the power supply voltage, running current and insulation resistance are normal on a regular basis.If the following conditions are found, the equipment should be shut down immediately to eliminate the fault:
5. - Under the rated working conditions, the current exceeds 20%.
6. - The dynamic water level drops to the inlet section, resulting in intermittent drainage.
7. - The submersible pump vibrates violently or emits noisy sounds.
8. - The power supply voltage is lower than 340 volts.
9. - There is a phase blown out in the fuse.
10. - The water pipe is damaged.
11. - The thermal insulation resistance between the motor and the ground is less than 0.5 megaohm.

1. 5. Disassembly device:
2. - Untie the cable, take off the pipe part and remove the line protection plate.
3. - Unscrew the drain screw and exclude all water in the motor chamber.
4. - Take out the filter and loosen the fixing screw on the coupling fixed to the motor shaft.
5. - Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to the level of the device to prevent the bending of the pump shaft when separating).
6. - The disassembly sequence of the pump is as follows: (see Figure 1) water inlet section, impeller, shunt shell, impeller, check valve body. When removing the impeller, use special tools to loosen the cone sleeve fixed to the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various parts.
7. - The disassembly process of the motor is as follows: (see Figure 1) place the motor on the platform, and remove the nuts, base, shaft head lock nut, thrust plate, key, lower guide bearing. seat, and tie rod bolts from the bottom of the motor in order (see Figure 1), and then take out the rotor (be careful not to damage the wiring harness) and finally take out the connector and upper guide bearing seat.
8. - Assembly unit: before assembly, all parts should be cleaned of rust and dirt, and smear sealant on all the surfaces and fasteners, and then assemble in the opposite order of disassembly (the movement of the motor shaft after assembly is about 1 mm). After assembly, the coupling should be flexible, and then wear the filter for machine test. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

 1, khipha amanzi ku-motor cavity (ikakhulukazi ebusika ukuvimbela injini ukuba ingaqhwa), futhi ubophe ikhebula kahle.

 2, gcina endlini engaphakathi engenazo izinto ezonakalisayo namagesi, nezinga lokushisa elingaphansi kuka-40 °C.

 3, ukusetshenziswa isikhathi eside kufanele sinake ukuvimbela nokugqwala amaphampu submersible.

01 Ukuphuza amanzi omthombo ojulile

02 Ukuhlinzekwa kwamanzi asezingeni eliphezulu

03 amanzi asezintabeni 

04 amanzi ombhoshongo

05 Ukuchelela kwezolimo

06 ukuchelela engadini

07 amanzi omfula

08 amanzi asekhaya