Caidéal Intumtha Deep Well 300QJR

This hot water pump adopts the motor made of 50W400 grade high quality cold rolled silicon steel, which is stamped by high speed punch press. It has the advantages of low stator iron loss and low self-heating. The motor winding is designed for hot water pump, high temperature resistance and anti-aging. The winding has water resistance, and adopts 3CR13 stainless steel blade shaft, high temperature resistant bushing and other high quality accessories to enable it to operate for a long time at high temperature, and can be used with frequency converter, so as to automatically adjust according to the amount of water used. This hot water pump is the ideal choice for your hot water equipment, which can operate stably and efficiently, providing you with a lasting hot water supply.

The product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply submersible pump. With water quality requirements: water temperature is not higher than 20 °C; solid impurities content (mass ratio) is not more than 0.01%; PH value (pH) is 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The electric pump adopts closed or water sealed wet structure, before use must be submersible motor inner cavity filled with clean water to prevent empty, and then tighten the water and air bolts, otherwise not to use. Its work should be completely immersed in water, immersion depth is not more than 70 meters, the distance between the bottom of the pump and the bottom of the well is not less than 3 meters. Well water inflow quantity should be able to meet the electric pump water output and continuous operation, the output water quantity should be controlled at 0.7-1.2 times of the rated flow. The well should be vertical, the electric pump can not be used horizontally or inclined, only vertically placed. The electric pump must be equipped with cables and external overload protection device as required. It is strictly prohibited to conduct no-load test under no water condition.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, go docht de réir fhorálacha an ardaitheoir caidéil, raon sreafa úsáide, chun cosc ​​a chur ar shreabhadh íseal nó fórsa caidéalaithe ard-ardaitheoir, an t-imthaca sá agus páirteanna eile den chaitheamh, an ró-ualach mótair dóite

6, tar éis an caidéal síos an tobair, níor chóir go mbeadh tomhas an mhótair go dtí an fhriotaíocht inslithe talún níos lú ná 100M, tar éis tús a chur leis an voltas agus an sruth a urramú, seiceáil an insliú foirceannadh mótair, cibé acu de réir na gceanglas; teocht suíomh stórála caidéil más lú ná an reophointe, ba chóir go mbeadh an t-uisce sa chuas mótair tirim, cosc ​​a chur ar an damáiste oighear uisce cuas mótair de bharr teocht íseal.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The main characteristic of this product is that the motor is a water-cooled submersible three-phase asynchronous motor, and the motor cavity is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the expansion-contraction pressure difference in the body caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft and the motor shaft are connected together through a coupling, and a thrust bearing is installed at the bottom of the motor. The lubrication of the motor and the pump bearing is realized through water lubrication. The stator winding of the motor is made of high-quality well motor winding wire, with high insulation performance. The pump is designed by computer CAD, with simple structure and good technical performance.

(1) Ullmhúchán roimh shuiteáil:
1. Seiceáil an gcomhlíonann an caidéal báite na coinníollacha úsáide agus an raon feidhme a shonraítear sa lámhleabhar.
2. Ag baint úsáide as obiect trom le trastomhas comhionann le trastomhas seachtrach uasta an chaidéil báite, tomhais an féidir le trastomhas inneldiameter an tobair an caidéal báite a fheistiú, agus tomhas an gcomhlíonann doimhneacht an tobair na ceanglais suiteála.
3. Seiceáil an bhfuil tolladh an tobair glan agus an bhfuil uisce an tobair suaite. Ná húsáid caidéal leictreach intumtha riamh chun láib agus gaineamh an chaidéil welor a ní chun damáiste roimh am a sheachaint don chaidéal leictreach intumtha.
4. Seiceáil an bhfuil suíomh an clamp suiteála welhead oiriúnach agus an féidir leis cáilíocht an aonaid iomláin a sheasamh
5. Seiceáil an bhfuil na comhpháirteanna caidéil báite críochnaithe agus suiteáilte i gceart de réir an léaráid tionóil sa lámhleabhar Bain an scáileán scagaire agus rothlaigh an cúpláil féachaint an rothlaíonn sé go solúbtha
6. Díscriú an scriú uisce agus líon an cuas mótair le huisce glan, neamhchreimneach (tabhair faoi deara. Bí cinnte é a chomhdú), ansin déan an scriú uisce níos doichte. Tar éis 12 uair an chloig d'instealladh uisce, níor chóir go mbeadh friotaíocht inslithe an mhótair níos lú ná 150M Q nuair a thomhaistear é le tábla croith 500V.
7. Comhpháirteach cábla, gearrtha as muinchille rubair 120mm ó thaobh amháin den chábla atá ag dul as oifig agus an cábla meaitseála le scian leictreoir ansin tuislithe fad na trí chroí-shreanga i gcruth céimnithe, craiceann croí copair 20mm, scrape an ocsaíd. ciseal ar an taobh amuigh den sreang copair le scian nó éadach gaineamh, agus cuir isteach an dá foircinn sreang ceangailte i palirs.Tar éis ceangail an ciseal go docht le sreang copar fíneáil, sádráil sé go maith agus go daingean, agus gaineamh ar bith. burrs ar an dromchla. Ansin, ar aghaidh chuig na trí alt, bain úsáid as téip inslithe polaistiréire chun iad a chuimilt go leathchruach ar feadh trí lasca. Fillte an dá cheann den chiseal fillte go docht le snáithe nyion, agus ansin úsáid modh leathchruachta chun an téip a chuimilt ar feadh trí shraith. Wrap an outellayer le ard-bhrú téip inslithe ar feadh trí shraith. Ar deireadh, fillte na trí shnáithe le chéile agus fillte arís agus arís eile ar feadh cúig sraitheanna le téip ardbhrú. Ní mór gach ciseal a bheith ceangailte go docht, agus ní mór na hailt interlayer a bheith daingean agus fimm chun uisce a chosc ó treá agus damáiste a dhéanamh don insliú, Tar éis timfhilleadh, soak in uisce ag teocht an tseomra de 20 'c ar feadh 12 uair an chloig, agus friotaíocht inslithe a thomhas le tábla chroitheadh. , nár chóir a bheith níos lú ná 100M Ω

Is é seo a leanas an léaráid próiseas sreangú cábla ceangailte:

8. Bain úsáid as multimeter chun a sheiceáil an bhfuil na sreanga trí chéim ceangailte agus an bhfuil an fhriotaíocht DC cothromaithe thart.
9. Seiceáil an bhfuil an ciorcad agus an cumas claochladáin ró-ualach, agus ansin an lasc cosanta ró-ualach nó an trealamh tosaigh a nascadh. Féach Tábla 2 le haghaidh samhlacha sonracha, agus ansin Doirt buicéad uisce isteach sa chaidéal uisce ón asraon caidéil uisce chun na imthacaí rubair a lubricadh sa chaidéal, agus ansin cuir an caidéal leictreach intumtha ina seasamh agus go seasta.Start (gan níos mó ná soicind amháin) agus seiceáil an bhfuil an treo stiúrtha comhsheasmhach leis an gcomhartha stiúrtha. Mura bhfuil, babhtáil aon dá chónaisc den chábla trí phas. Ansin shuiteáil an scagaire agus ullmhaigh tú chun dul síos ar an tobar. Má úsáidtear é in ócáidí speisialta (cosúil le díoga, díoga, aibhneacha, locháin, locháin, etc.), ní mór an caidéal leictreach a thalamh go hiontaofa.

(2) Trealamh agus uirlisí suiteála:
1. Péire amháin de slabhraí ardaithe ar feadh níos mó ná dhá tonna.
2. Tripod le airde ingearach nach lú ná ceithre mhéadar.
3. Dhá rópa crochta (rópaí sreang) ar féidir leo meáchan níos mó ná tonna amháin a iompróidh (is féidir meáchan sraith iomlán caidéil uisce a iompróidh).
4. Suiteáil dhá phéire teanntáin (splints).
5. Wrenches, casúir, scriúirí, uirlisí leictreacha agus ionstraimí, etc.

(3) Suiteáil caidéil leictreacha:
1. Taispeántar léaráid suiteála an chaidéil leictreacha intumtha i bhFíor 2. Taispeántar na toisí suiteála sonracha i dTábla 3 "Liosta Toisí Suiteála an Chaidéil Leictreach Intumtha".

2. Is féidir caidéil leictreacha báite le ceann níos lú ná 30 méadar a ardú go díreach isteach sa tobar ag baint úsáide as píobáin agus rópaí sreang nó rópaí cnáib eile ar féidir leo meáchan iomlán an mheaisín iomláin, píopaí uisce, agus uisce sna píopaí a iompar.

3. Úsáideann caidéil le ceann níos mó ná 30 méadar píopaí cruach, agus is é seo a leanas an t-ord suiteála:
① Bain úsáid as clamp chun ceann uachtarach an chaidéil uisce a chlampáil (tá an mótar agus an caidéal uisce ceangailte ag an am seo), ardaigh sé le slabhra crochta, agus ceangail go mall isteach sa tobar é go dtí go gcuirfidh tú an clamp ar cheann an tobair agus bain an slabhra crochta.
② Bain úsáid as péire teanntáin eile chun píopa a chlampáil, é a ardú le slabhra crochta 15 cm ar shiúl ón flange, agus é a ísliú go mall. Idir flange píopa agus flange caidéil Cuir an ceap rubair in áit agus déan an píopa agus an caidéal a dhéanamh níos doichte go cothrom le boltaí, cnónna agus leicneáin earraigh.
③ Ardaigh an caidéal báite beagán, bain an clamp ar thaobh uachtarach an chaidéil uisce, ceangail an cábla go daingean leis an bpíobán uisce le téip plaisteach, agus é a cheangal go mall síos go dtí go gcuirtear an clamp ag ceann an tobair.
④ Bain úsáid as an modh céanna chun na píopaí uisce go léir a cheangal isteach sa tobar.
⑤ Tar éis an cábla luaidhe-amach a bheith ceangailte leis an lasc rialaithe, tá sé ceangailte leis an soláthar cumhachta trí phas.

(4) Rudaí le tabhairt faoi deara le linn na suiteála:
1. Má aimsítear feiniméan jamming le linn an phróisis caidéalaithe, cas nó tarraing an píopa uisce chun an pointe jamming a shárú. Mura n-oibríonn bearta éagsúla fós, le do thoil Ná cuir an caidéal síos chun damáiste a sheachaint don chaidéal leictreach intumtha agus don tobar.
2. Le linn na suiteála, ba chóir eochaircheap rubair a chur ar flange gach píopa agus é a cheangal go cothrom.
3. Nuair a íslítear an caidéal uisce isteach sa tobar, ba chóir é a chur i lár an phíobáin tobair chun an caidéal a chosc ó bheith ag rith i gcoinne bhalla an tobair ar feadh i bhfad, rud a fhágann go mbeidh an caidéal ag creathadh agus an mótar a scuabadh agus a dhó. .
4. Déan doimhneacht an chaidéil uisce go bun an tobair a chinneadh de réir coinníollacha sreafa gaineamh agus siolta an tobair. Ná cuir an caidéal sa láib. De ghnáth ní lú ná 3 mhéadar an fad ón gcaidéal uisce go bun an tobair (féach Fíor 2).
5. Níor cheart go mbeadh doimhneacht iontrála uisce an chaidéil uisce níos lú ná 1-1.5 méadar ón leibhéal uisce dinimiciúil go dtí an nód inlet uisce (féach Fíor 2). Seachas sin, féadfar damáiste a dhéanamh go héasca ar imthacaí an chaidéil uisce.
6. Ní féidir le hardaitheoir an chaidéil uisce a bheith ró-íseal. Seachas sin, is gá comhla geata a shuiteáil ar phíblíne uisce an tobair chun sreabhadh an chaidéil ag an bpointe sreafa rátáilte a rialú chun an mótar a chosc ó ró-ualach agus a dhó mar gheall ar rátaí sreafa móra.
7. Nuair a bhíonn an caidéal uisce ag rith, ba cheart go mbeadh an t-aschur uisce leanúnach agus fiú, ba cheart go mbeadh an sruth cobhsaí (faoi choinníollacha oibre rátáilte, go ginearálta gan níos mó ná 10% den sruth rátáilte), agus níor cheart go mbeadh aon chreathadh nó torann ann. Má tá aon neamhghnáchaíocht ann, ba chóir an meaisín a stopadh chun an chúis a fháil amach agus é a dhíchur.
8. Nuair a shuiteáil tú, tabhair aird ar shocrú na sreinge talún mótair (féach Fíor 2). Nuair is píopa cruach é an píopa uisce, déan é a threorú as clamp an tobair; nuair is píopa plaisteach an píopa uisce, é a threorú ó mharc talún an chaidéil leictreach.

 After installation of the underwater pump, it is necessary to recheck the insulation resistance and three-phase continuity of the switch, and check whether the connection between the instrument and the starting equipment is wrong. If there is no problem, you can start the test machine. After starting, observe whether the indication reading of each instrument is correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. Four hours after the first operation of the pump, it should be turned off and the thermal insulation resistance of the motor should be quickly tested, and its value should not be less than 0.5 megaohm. After stopping the pump, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to excessive current. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to eliminate the fault:

1 the current exceeds 20% under the rated working condition.

2 the dynamic water level drops to the inlet section, resulting in intermittent drainage.

3 the underwater pump vibrates violently or emits huge noise.

4 the supply voltage is lower than 340 volts.

5 a fuse is burned.

6 the water pipe is damaged.

7 the thermal insulation resistance of the motor to the ground is less than 0.5 megaohm.

When disassembling the device, it is necessary to untie the cable bundle and remove the pipeline part and the line protection plate. Remove the drain bolt and exclude all water in the motor chamber. Remove the filter element and loosen the screw on the coupling fixed to the motor shaft. Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to placing the device horizontally when separating to prevent the bending of the pump shaft). The sequence of disassembling the pump is as follows: (see Figure 1) water inlet section, impeller, water inlet shell, impeller. Check the valve body, and use a special tool to loosen the cone sleeve fixed to the impeller when removing the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various components. The disassembly process of the motor is as follows: (see Figure 1) put the motor on the platform, and remove the nuts on the screw (pull rod bolt), base, shaft head lock nut, thrust plate, key and lower guide rail - bearing seat, bolt, and then remove the rotor (be careful not to damage the wiring harness), and finally remove the connecting parts and upper guide bearing seat. Unit assembly: before assembly, the rust and dirt of each component should be cleaned, and the sealant should be coated on each mating surface and fastener, and then assembled in the opposite order of disassembly (the movement of the motor shaft after assembly is about one millimeter), after the assembly is completed, the coupling should be flexibly rotated, and then the filter element should be placed for testing. Each time the underwater electric pump has been used for one year, or less than one year but has been immersed for two years, it must be disassembled and inspected in accordance with Article 5 and replace the worn parts.

 1, cuir an t-uisce amach sa chuas mótair (go háirithe sa gheimhreadh chun an mótar a chosc ó reo), agus an cábla a cheangal go maith.

 2, stóráil i seomra faoi dhíon gan substaintí agus gáis creimneach, ag teocht faoi bhun 40 ° C.

 3, ba chóir go fadtéarmach aird a thabhairt ar chosc meirge na caidéil báite.

01 Iontógáil uisce domhain tobair

02 Soláthar uisce ard-ardú

03 soláthar uisce sléibhe 

04 túr uisce

05 Uisciúcháin talmhaíochta

06 uisciúcháin gairdín

07 iontógáil uisce abhann

08 uisce tí