300QJR iMpompa eNgantywila eNzulu Kakuhle

This hot water pump adopts the motor made of 50W400 grade high quality cold rolled silicon steel, which is stamped by high speed punch press. It has the advantages of low stator iron loss and low self-heating. The motor winding is designed for hot water pump, high temperature resistance and anti-aging. The winding has water resistance, and adopts 3CR13 stainless steel blade shaft, high temperature resistant bushing and other high quality accessories to enable it to operate for a long time at high temperature, and can be used with frequency converter, so as to automatically adjust according to the amount of water used. This hot water pump is the ideal choice for your hot water equipment, which can operate stably and efficiently, providing you with a lasting hot water supply.

The product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply submersible pump. With water quality requirements: water temperature is not higher than 20 °C; solid impurities content (mass ratio) is not more than 0.01%; PH value (pH) is 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The electric pump adopts closed or water sealed wet structure, before use must be submersible motor inner cavity filled with clean water to prevent empty, and then tighten the water and air bolts, otherwise not to use. Its work should be completely immersed in water, immersion depth is not more than 70 meters, the distance between the bottom of the pump and the bottom of the well is not less than 3 meters. Well water inflow quantity should be able to meet the electric pump water output and continuous operation, the output water quantity should be controlled at 0.7-1.2 times of the rated flow. The well should be vertical, the electric pump can not be used horizontally or inclined, only vertically placed. The electric pump must be equipped with cables and external overload protection device as required. It is strictly prohibited to conduct no-load test under no water condition.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, ngokungqongqo ngokwemiqathango yokunyuswa kwempompo, uluhlu lokuhamba kokusetyenziswa, ukuthintela ukuhamba okuphantsi okanye amandla okumpompa aphezulu, ukunyanzeliswa kwe-thrust kunye nezinye iindawo zokunxiba, ukugcwala kwemoto kutshiswe.

I-6, emva kwempompo phantsi kwequla, umlinganiselo we-motor ukuya kwi-insulation ye-insulation yomhlaba akufanele ibe ngaphantsi kwe-100M, emva kokuqala ukujonga i-voltage kunye ne-current, khangela i-motor winding insulation, nokuba ihambelana neemfuno; ubushushu bendawo yokugcina impompo ukuba bungaphantsi kwendawo yokukhenkceza, kufuneka yome amanzi kumqolo wemoto, kuthintelwe umngxuma wemoto umonakalo womkhenkce obangelwa bubushushu obuphantsi.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The main characteristic of this product is that the motor is a water-cooled submersible three-phase asynchronous motor, and the motor cavity is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the expansion-contraction pressure difference in the body caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft and the motor shaft are connected together through a coupling, and a thrust bearing is installed at the bottom of the motor. The lubrication of the motor and the pump bearing is realized through water lubrication. The stator winding of the motor is made of high-quality well motor winding wire, with high insulation performance. The pump is designed by computer CAD, with simple structure and good technical performance.

(1)Ulungiselelo phambi kofakelo:
1. Jonga ukuba impompo engaphantsi kwamanzi iyahlangabezana nemiqathango yokusetyenziswa kunye nobubanzi obuchazwe kwincwadana.
2. Ukusebenzisa i-obiect enzima ene-diameter elingana nobukhulu obungaphandle bedayamitha yempompo engaphantsi kwamanzi, linganisa ukuba i-inneldiameter ye-wellbore ingafanelana nempompo engaphantsi kwamanzi, kwaye ulinganise ukuba ubunzulu bomthombo buhlangabezana neemfuno zokufakela.
3. Jonga ukuba iqula licocekile na kunye nokuba amanzi amgxobhozo na. Ungaze usebenzise impompo yombane engaphantsi kwamanzi ukuhlamba udaka lwempompo ye-welor kunye namanzi esanti ukunqanda umonakalo ophambi kwexesha kwimpompo yombane engaphantsi kwamanzi.
4. Khangela ukuba indawo ye-welhead yokufakela i-clamp ifanelekile kwaye ingaba inokumelana nomgangatho weyunithi yonke.
5. Khangela ukuba izixhobo zempompo eziphantsi kwamanzi zigqityiwe kwaye zifakwe ngokufanelekileyo ngokwedayagram yendibano kwincwadana Susa isikrini sokucoca kwaye ujikelezise ukudibanisa ukuze ubone ukuba ijikeleza ngokuguquguqukayo.
6. Khupha isikrufu samanzi uze ugcwalise umngxuma wemoto ngamanzi acocekileyo, angadlekiyo (qaphela. qiniseka ukuba uyasifafa), uze uqinise isikrufu samanzi. Emva kweeyure ezili-12 zenaliti yamanzi, ukuxhathisa kwe-insulation ye-motor akufanele kube ngaphantsi kwe-150M Q xa kulinganiswa netafile yokungcangcazela ye-500V.
7. Umdibaniso wekheyibhile, unqumle umkhono werabha oyi-120mm kwelinye icala lentambo ephumayo kunye nentambo yokumatanisa enemela yomntu wombane uze ugxadazele ubude beengcingo ezintathu ezingundoqo ngendlela enyathelweyo, krazula umbindi wobhedu oyi-20mm, krazula ioksidi. umaleko ongaphandle kocingo lobhedu ngemela okanye ngelaphu lesanti, kwaye ufake iziphelo zocingo ezimbini eziqhagamshelweyo kwi palirs.Emva kokubopha umaleko ngokuqinileyo ngocingo olucolekileyo lobhedu, i-solder ngokucokisekileyo kwaye ngokuqinileyo, kunye nesanti yayo nayiphi na. amaqhuma phezu komhlaba. Emva koko, kumalungu amathathu, sebenzisa iteyiphu yokugquma i-polyvester ukuyisonga ngendlela epakishwe kabini kwizitya zokuhlambela ezintathu. Songa iziphelo ezibini zomaleko wokusonga ngokuqinileyo ngomsonto we-nyion, kwaye emva koko usebenzise indlela epakishwe kabini ukusonga iteyiphu kwiileya ezintathu. Songa i-outellayer ngetape yoxinzelelo oluphezulu lwe-insulation kwimigangatho emithathu. Ekugqibeleni, phinda udibanise imisonto emithathu kwaye uyibophe ngokuphindaphindiweyo kwi-fivelayers nge-tape yoxinzelelo oluphezulu. Umaleko ngamnye kufuneka ubotshelelwe ngokuqinileyo, kwaye amalungu e-interlayer kufuneka abe ngqongqo kwaye abe fimm ukukhusela amanzi ukuba angangeni kwaye wonakalise isigqubuthelo, Emva kokusonga, faka amanzi kwindawo yobushushu obungama-20 'c iiyure ezili-12, kwaye ulinganise ukuxhathisa ukugquma ngetafile eshukumayo. , ekufuneka ingabi ngaphantsi kwe-100M Ω

Umzobo oqhotyoshelweyo wenkqubo yokufaka iintambo zentambo umi ngolu hlobo lulandelayo:

8. Sebenzisa i-multimeter ukujonga ukuba ngaba iingcingo zesigaba sesithathu zidibaniswe kunye nokuba ukuchasana kwe-DC kuphantse kulinganiswe.
9. Khangela ukuba isekethe kunye nomthamo we-transformer ugcwele kakhulu, kwaye emva koko uqhagamshele i-switch yokukhusela okanye uqalise izixhobo. Jonga iTheyibhile yesi-2 kwiimodeli ezithile, kwaye emva koko galela ibhakethi lamanzi kwimpompo yamanzi ukusuka kwindawo yokupompoza amanzi ukuthambisa iibheringi zerabha kwimpompo, kwaye emva koko ubeke impompo yombane entywilayo ngokuthe tye kwaye izinzile.Qala (ungabi ngaphezu komzuzwana omnye) kwaye ujonge ukuba ngaba ulwalathiso lokuqhuba luyahambelana nophawu lokuqhuba. Ukuba akunjalo, tshintsha naziphi na izihlanganisi ezibini zesigaba sesithathu sentambo. Emva koko faka isihluzo kwaye ulungiselele ukuhla equleni. Ukuba isetyenziswe ngezihlandlo ezikhethekileyo (ezifana nemijelo, imisele, imilambo, amachibi, amachibi, njl. njl.), impompo yombane kufuneka isekelwe ngokuthembekileyo.

(2)Izixhobo zofakelo kunye nezixhobo:
1. Ipere enye yamatyathanga okuphakamisa ngaphezulu kweetoni ezimbini.
2. I-tripod enobude obuthe nkqo obungekho ngaphantsi kweemitha ezine.
3. Iintambo ezimbini ezijingayo (iintambo zocingo) ezinokuthwala ubunzima obungaphezu kwetoni enye (zinokuthwala ubunzima beseti epheleleyo yeempompo zamanzi).
4. Fakela izibini ezimbini zeeclamps (i-splints).
5. Izitshixo, izando, i-screwdrivers, izixhobo zombane kunye nezixhobo, njl.

(3)Ufakelo lwempompo yombane:
1. Umzobo wofakelo lwempompo yombane engaphantsi kwamanzi iboniswe kuMzobo 2. Imilinganiselo ethile yokufakela iboniswe kwiThebhile 3 "Uluhlu lweMilinganiselo yokuFakela iPump yoMbane ongaphantsi kwamanzi".

2. Iimpompo zombane ezingaphantsi kwamanzi ezinentloko engaphantsi kweemitha ezingama-30 zinokunyuswa ngokuthe ngqo equleni kusetyenziswa imibhobho kunye neentambo zocingo okanye ezinye iintambo zehemp ezinokuthwala ubunzima obupheleleyo bomatshini wonke, imibhobho yamanzi, kunye namanzi kwimibhobho.

3. Iipompo ezinentloko yeemitha ezingaphezu kwe-30 zisebenzisa iipayipi zensimbi, kwaye ulandelelwano lofakelo lulandelayo:
①Sebenzisa ibamba ukucinezela isiphelo esiphezulu sempompo yamanzi (injini kunye nempompo yamanzi sele idityanisiwe ngeli xesha), yiphakamise ngetsheyini ejingayo, kwaye uyibophe ngokukhawuleza equleni de ubeke isibambiso entloko kwaye uyisuse. ikhonkco elijingayo.
② Sebenzisa enye ipere yeziqhoboshi ukuqhobosha umbhobho, uwuphakamise ngetyathanga elijingayo 15 cm kude neflange, kwaye uwuhlise kancinane. Phakathi kweflange yombhobho kunye neflange yepompoFaka ipadi yerabha endaweni kwaye uqinise umbhobho kwaye umpompe ngokulinganayo ngeebholiti, iinati kunye newasher zasentwasahlobo.
③ Phakamisa kancinane impompo entywilayo emanzini, susa isithinteli esikwisiphelo esiphezulu sempompo yamanzi, qhina intambo ngokuqinileyo kumbhobho wamanzi ngeteyiphu yeplastiki, kwaye uyibophe kancinane de Ibamba libekwe emthonjeni.
④Sebenzisa indlela efanayo ukubopha yonke imibhobho yamanzi equleni.
⑤Emva kokuba ikhebula elikhokelayo liqhagamshelwe kwisitshixo solawulo, liqhagamshelwe kunikezelo lwamandla amanqanaba amathathu.

(4)Izinto ekufuneka uziqwalasele ngexesha lofakelo:
1. Ukuba i-jamming phenomenon ifunyenwe ngexesha lenkqubo yokupompa, jika okanye utsale umbhobho wamanzi ukuze unqobe i-jamming point. Ukuba imilinganiselo eyahlukeneyo ayisebenzi, nceda unganyanzeli impompo phantsi ukunqanda umonakalo kwimpompo yombane engaphantsi kwamanzi kunye nequla.
2. Ngethuba lofakelo, i-rubber pad kufuneka ifakwe kwi-flange yombhobho ngamnye kwaye iqiniswe ngokulinganayo.
3. Xa impompo yamanzi ithotywa equleni, kufuneka ibekwe embindini wombhobho wequla ukuthintela ukuba impompo ihambe ngaphaya kodonga lwequla ixesha elide, nto leyo ebangela ukuba impompo ingcangcazele kwaye imotor itshayele kwaye itshise. .
4. Qinisekisa ubunzulu bempompo yamanzi ukuya ezantsi kwequla ngokwesanti equkuqelayo kunye neemeko zentlenge equleni. Musa ukungcwaba impompo eludakeni. Umgama ukusuka kumpompo wamanzi ukuya ezantsi kwequla awukho ngaphantsi kweemitha ezi-3 (jonga umfanekiso 2).
5. Ubunzulu bokungena kwamanzi kwimpompo yamanzi kufuneka bungabi ngaphantsi kwe-1-1.5 yeemitha ukusuka kwinqanaba lamanzi aguquguqukayo ukuya kwindawo yokungena kwamanzi (jonga uMfanekiso 2). Ngaphandle koko, iibheringi zempompo zamanzi zinokonakala lula.
6. Ukunyuswa kwempompo yamanzi akunakuba phantsi kakhulu. Kungenjalo, ivalve yesango kufuneka ifakwe kumbhobho wamanzi osentloko yomthombo ukulawula ukuhamba kwempompo kwindawo yokuqukuqela ehleliweyo ukuthintela ukugcwala okugqithisileyo kwemoto kwaye itshiswe ngenxa yamazinga amakhulu okuhamba.
7. Xa umpompo wamanzi usebenza, ukukhutshwa kwamanzi kufuneka kuqhubeke kwaye nokuba, okwangoku kufuneka kuzinzile (phantsi kweemeko zokusebenza ezilinganisiweyo, ngokuqhelekileyo akukho ngaphezu kwe-10% ye-current rated current), kwaye akufanele kubekho ukungcangcazela okanye ingxolo. Ukuba kukho nakuphi na ukungaqhelekanga, umatshini kufuneka umiswe ukufumanisa unobangela kwaye upheliswe.
8. Xa ufaka, qwa lasela ukusetwa kwe-motor grounding wire (jonga umfanekiso 2). Xa umbhobho wamanzi ungumbhobho wentsimbi, yiholele kwi-clamp ye-wellhead clamp; xa umbhobho wamanzi ungumbhobho weplastiki, ukhokele ukusuka kwindawo yokubeka ipompo yombane.

 After installation of the underwater pump, it is necessary to recheck the insulation resistance and three-phase continuity of the switch, and check whether the connection between the instrument and the starting equipment is wrong. If there is no problem, you can start the test machine. After starting, observe whether the indication reading of each instrument is correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. Four hours after the first operation of the pump, it should be turned off and the thermal insulation resistance of the motor should be quickly tested, and its value should not be less than 0.5 megaohm. After stopping the pump, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to excessive current. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to eliminate the fault:

1 the current exceeds 20% under the rated working condition.

2 the dynamic water level drops to the inlet section, resulting in intermittent drainage.

3 the underwater pump vibrates violently or emits huge noise.

4 the supply voltage is lower than 340 volts.

5 a fuse is burned.

6 the water pipe is damaged.

7 the thermal insulation resistance of the motor to the ground is less than 0.5 megaohm.

When disassembling the device, it is necessary to untie the cable bundle and remove the pipeline part and the line protection plate. Remove the drain bolt and exclude all water in the motor chamber. Remove the filter element and loosen the screw on the coupling fixed to the motor shaft. Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to placing the device horizontally when separating to prevent the bending of the pump shaft). The sequence of disassembling the pump is as follows: (see Figure 1) water inlet section, impeller, water inlet shell, impeller. Check the valve body, and use a special tool to loosen the cone sleeve fixed to the impeller when removing the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various components. The disassembly process of the motor is as follows: (see Figure 1) put the motor on the platform, and remove the nuts on the screw (pull rod bolt), base, shaft head lock nut, thrust plate, key and lower guide rail - bearing seat, bolt, and then remove the rotor (be careful not to damage the wiring harness), and finally remove the connecting parts and upper guide bearing seat. Unit assembly: before assembly, the rust and dirt of each component should be cleaned, and the sealant should be coated on each mating surface and fastener, and then assembled in the opposite order of disassembly (the movement of the motor shaft after assembly is about one millimeter), after the assembly is completed, the coupling should be flexibly rotated, and then the filter element should be placed for testing. Each time the underwater electric pump has been used for one year, or less than one year but has been immersed for two years, it must be disassembled and inspected in accordance with Article 5 and replace the worn parts.

 1, khupha amanzi kwi-motor cavity (ingakumbi ebusika ukukhusela i-motor ekukhenkceni), kwaye ubophe intambo kakuhle.

 2, gcina kwigumbi elingaphakathi elingenazo izinto ezonakalisayo kunye neegesi, ezinobushushu obungaphantsi kwama-40 °C.

 I-3, ukusetyenziswa kwexesha elide kufuneka kuhlawule ingqalelo ekuthinteleni umhlwa kweempompo ezingaphantsi kwamanzi.

01 Ukusela amanzi kwiqula elinzulu

02 Ubonelelo lwamanzi olukwizinga eliphezulu

03 unikezelo lwamanzi entabeni 

04 amanzi enqaba

05 Ukunkcenkceshela kwezolimo

06 ukunkcenkceshela egadini

07 amanzi omlambo

08 amanzi asekhaya