Potopna črpalka za globok vodnjak 300QJR

This hot water pump adopts the motor made of 50W400 grade high quality cold rolled silicon steel, which is stamped by high speed punch press. It has the advantages of low stator iron loss and low self-heating. The motor winding is designed for hot water pump, high temperature resistance and anti-aging. The winding has water resistance, and adopts 3CR13 stainless steel blade shaft, high temperature resistant bushing and other high quality accessories to enable it to operate for a long time at high temperature, and can be used with frequency converter, so as to automatically adjust according to the amount of water used. This hot water pump is the ideal choice for your hot water equipment, which can operate stably and efficiently, providing you with a lasting hot water supply.

The product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply submersible pump. With water quality requirements: water temperature is not higher than 20 °C; solid impurities content (mass ratio) is not more than 0.01%; PH value (pH) is 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The electric pump adopts closed or water sealed wet structure, before use must be submersible motor inner cavity filled with clean water to prevent empty, and then tighten the water and air bolts, otherwise not to use. Its work should be completely immersed in water, immersion depth is not more than 70 meters, the distance between the bottom of the pump and the bottom of the well is not less than 3 meters. Well water inflow quantity should be able to meet the electric pump water output and continuous operation, the output water quantity should be controlled at 0.7-1.2 times of the rated flow. The well should be vertical, the electric pump can not be used horizontally or inclined, only vertically placed. The electric pump must be equipped with cables and external overload protection device as required. It is strictly prohibited to conduct no-load test under no water condition.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, strogo v skladu z določbami dvigala črpalke, obseg uporabe pretoka, za preprečevanje nizkega pretoka ali visokega dviga črpalne sile, potisni ležaj in drugi deli obrabe, preobremenitev motorja zgorela

6, po črpalki po vodnjaku meritev izolacijske upornosti motorja do tal ne sme biti manjša od 100M, po začetku opazovanja napetosti in toka preverite izolacijo navitja motorja, ali je v skladu z zahtevami; Če je temperatura na mestu shranjevanja črpalke nižja od ledišča, je treba vodo v votlini motorja posušiti, preprečiti poškodbe vodnega ledu v votlini motorja zaradi nizke temperature.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The main characteristic of this product is that the motor is a water-cooled submersible three-phase asynchronous motor, and the motor cavity is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the expansion-contraction pressure difference in the body caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft and the motor shaft are connected together through a coupling, and a thrust bearing is installed at the bottom of the motor. The lubrication of the motor and the pump bearing is realized through water lubrication. The stator winding of the motor is made of high-quality well motor winding wire, with high insulation performance. The pump is designed by computer CAD, with simple structure and good technical performance.

(1) Priprava pred namestitvijo:
1. Preverite, ali potopna črpalka ustreza pogojem uporabe in obsegu, navedenim v priročniku.
2. Z uporabo težkega predmeta s premerom, ki je enak največjemu zunanjemu premeru potopne črpalke, izmerite, ali notranji premer vrtine ustreza potopni črpalki, in izmerite, ali globina vrtine ustreza zahtevam za namestitev.
3. Preverite, ali je vrtina čista in ali je voda v vodnjaku motna. Nikoli ne uporabljajte potopne električne črpalke za izpiranje blata in peska črpalke welor, da preprečite prezgodnje poškodbe potopne električne črpalke.
4. Preverite, ali je položaj namestitvene objemke glave valja primeren in ali lahko prenese kakovost celotne enote
5. Preverite, ali so komponente potopne črpalke dokončane in pravilno nameščene v skladu s shemo sestavljanja v priročniku. Odstranite mrežico filtra in zavrtite sklopko, da vidite, ali se vrti prožno
6. Odvijte vodni vijak in napolnite votlino motorja s čisto, nejedko vodo (upoštevajte, da ste jo napolnili), nato privijte vodni vijak. Po 12 urah vbrizgavanja vode izolacijska upornost motorja ne sme biti manjša od 150 M Q, merjena s stresalno mizo 500 V.
7. Kabelski spoj, z električarskim nožem odrežite 120-milimetrski gumijasti tulec z enega konca izhodnega kabla in ustreznega kabla, nato stopničasto razporedite dolžino treh žilnih žic, odlepite 20-milimetrsko bakreno jedro, postrgajte oksid plast na zunanji strani bakrene žice z nožem ali krpo za peskanje in dva povezana konca žice vstavite v palirje. Ko plast tesno povežete s fino bakreno žico, jo temeljito in trdno spajkajte ter pobrusite poljubno. neravnine na površini. Nato za tri spoje uporabite izolacijski trak iz polivestra, da jih ovijete na pol naložen način za tri umivalnike. Oba konca ovojne plasti tesno ovijte z nyion nitjo in nato uporabite metodo pol zlaganja, da ovijete trak za tri plasti. Ovijte zunanji sloj z visokotlačnim izolacijskim trakom za tri plasti. Na koncu zložite tri pramene skupaj in jih večkrat ovijte v pet plasti z visokotlačnim trakom. Vsaka plast mora biti tesno povezana, vmesni spoji pa morajo biti tesni in čvrsti, da preprečite, da bi voda prodrla in poškodovala izolacijo. Po ovijanju namočite v vodi pri sobni temperaturi 20 °C za 12 ur in izmerite izolacijski upor s stresalno mizo , ki ne sme biti manjši od 100M Ω

Priloženi diagram postopka ožičenja kabla je naslednji:

8. Z multimetrom preverite, ali so trifazne žice priključene in ali je upor DC približno uravnotežen.
9. Preverite, ali sta vezje in zmogljivost transformatorja preobremenjena, nato priključite stikalo za zaščito pred preobremenitvijo ali opremo za zagon. Glejte tabelo 2 za določene modele in nato vlijte vedro vode v vodno črpalko iz izhoda vodne črpalke, da namažete gumijaste ležaje v črpalki, nato pa postavite potopno električno črpalko pokonci in mirno. Zaženite (ne več kot ena sekunda) in preverite, ali je smer krmiljenja skladna z znakom za krmiljenje. Če ne, zamenjajte poljubna dva konektorja trifaznega kabla. Nato namestite filter in se pripravite na spust v vodnjak. Če se uporablja v posebnih priložnostih (kot so jarki, jarki, reke, ribniki, ribniki itd.), mora biti električna črpalka zanesljivo ozemljena.

(2) Oprema in orodje za namestitev:
1. En par dvižnih verig za več kot dve toni.
2. Stativ z navpično višino najmanj štiri metre.
3. Dve viseči vrvi (žični vrvi), ki lahko preneseta težo več kot eno tono (lahko preneseta težo celotnega kompleta vodnih črpalk).
4. Namestite dva para sponk (splintov).
5. Ključi, kladiva, izvijači, električna orodja in instrumenti itd.

(3) Namestitev električne črpalke:
1. Namestitveni diagram potopne električne črpalke je prikazan na sliki 2. Posebne namestitvene mere so prikazane v tabeli 3 "Seznam namestitvenih mer potopne električne črpalke".

2. Potopne električne črpalke z višino manj kot 30 metrov je mogoče dvigniti neposredno v vodnjak s pomočjo cevi in ​​žičnih vrvi ali drugih vrvi iz konoplje, ki lahko prenesejo polno težo celotnega stroja, vodovodnih cevi in ​​vode v ceveh.

3. Črpalke z višino nad 30 metrov uporabljajo jeklene cevi, zaporedje namestitve pa je naslednje:
①Uporabite objemko, da vpnete zgornji konec dela vodne črpalke (motor in vodna črpalka sta bila trenutno povezana), jo dvignite z visečo verigo in počasi privežite v vodnjak, dokler ne namestite objemke na glavo vodnjaka in odstranite viseča veriga.
② Uporabite drug par sponk, da vpnete cev, jo dvignite z visečo verigo 15 cm stran od prirobnice in jo počasi spustite. Med prirobnico cevi in ​​prirobnico črpalke Namestite gumijasto podlogo in enakomerno zategnite cev in črpalko z vijaki, maticami in vzmetnimi podložkami.
③ Rahlo privzdignite potopno črpalko, odstranite objemko na zgornjem koncu vodne črpalke, kabel trdno privežite na vodno cev s plastičnim trakom in ga počasi privežite, dokler objemka ni nameščena na ustju vodnjaka.
④Uporabite isto metodo za pritrditev vseh vodovodnih cevi v vodnjak.
⑤Ko je izhodni kabel priključen na krmilno stikalo, je priključen na trifazno napajanje.

(4) Stvari, ki jih morate upoštevati med namestitvijo:
1. Če med postopkom črpanja odkrijete pojav zagozditve, obrnite ali povlecite cev za vodo, da premagate točko zagozdenja. Če različni ukrepi še vedno ne delujejo, vas prosimo, da črpalke ne spustite na silo, da preprečite poškodbe potopne električne črpalke in vodnjaka.
2. Med namestitvijo je treba na prirobnico vsake cevi namestiti gumijasto blazinico in jo enakomerno zategniti.
3. Ko vodno črpalko spustite v vodnjak, jo postavite na sredino cevi vodnjaka, da preprečite, da bi črpalka dlje časa delovala ob steni vodnjaka, zaradi česar bi črpalka vibrirala, motor pa pometal in gorel .
4. Določite globino vodne črpalke do dna vodnjaka glede na razmere tekočega peska in mulja v vodnjaku. Ne zakopajte črpalke v blato. Razdalja od vodne črpalke do dna vodnjaka običajno ni manjša od 3 metrov (glej sliko 2).
5. Globina vstopa vode vodne črpalke ne sme biti manjša od 1-1,5 metra od dinamičnega nivoja vode do vozlišča vstopa vode (glej sliko 2). V nasprotnem primeru se lahko ležaji vodne črpalke zlahka poškodujejo.
6. Dvig vodne črpalke ne sme biti prenizek. V nasprotnem primeru je treba na cevovod za vodo na ustju vrtine namestiti zaporni ventil za nadzor pretoka črpalke pri nazivni točki pretoka, da se prepreči preobremenitev in izgorevanje motorja zaradi velikih pretokov.
7. Ko vodna črpalka deluje, mora biti izhod vode neprekinjen in enakomeren, tok mora biti stabilen (pri nazivnih delovnih pogojih običajno ne več kot 10 % nazivnega toka) in ne sme biti vibracij ali hrupa. Če pride do kakršnih koli nepravilnosti, je treba stroj ustaviti, da ugotovite vzrok in ga odpravite.
8. Pri namestitvi bodite pozorni na nastavitev ozemljitvene žice motorja (glejte sliko 2). Če je cev za vodo jeklena cev, jo speljite od objemke na ustju vodnjaka; če je cev za vodo plastična cev, jo speljite od oznake za ozemljitev električne črpalke.

 After installation of the underwater pump, it is necessary to recheck the insulation resistance and three-phase continuity of the switch, and check whether the connection between the instrument and the starting equipment is wrong. If there is no problem, you can start the test machine. After starting, observe whether the indication reading of each instrument is correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. Four hours after the first operation of the pump, it should be turned off and the thermal insulation resistance of the motor should be quickly tested, and its value should not be less than 0.5 megaohm. After stopping the pump, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to excessive current. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to eliminate the fault:

1 the current exceeds 20% under the rated working condition.

2 the dynamic water level drops to the inlet section, resulting in intermittent drainage.

3 the underwater pump vibrates violently or emits huge noise.

4 the supply voltage is lower than 340 volts.

5 a fuse is burned.

6 the water pipe is damaged.

7 the thermal insulation resistance of the motor to the ground is less than 0.5 megaohm.

When disassembling the device, it is necessary to untie the cable bundle and remove the pipeline part and the line protection plate. Remove the drain bolt and exclude all water in the motor chamber. Remove the filter element and loosen the screw on the coupling fixed to the motor shaft. Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to placing the device horizontally when separating to prevent the bending of the pump shaft). The sequence of disassembling the pump is as follows: (see Figure 1) water inlet section, impeller, water inlet shell, impeller. Check the valve body, and use a special tool to loosen the cone sleeve fixed to the impeller when removing the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various components. The disassembly process of the motor is as follows: (see Figure 1) put the motor on the platform, and remove the nuts on the screw (pull rod bolt), base, shaft head lock nut, thrust plate, key and lower guide rail - bearing seat, bolt, and then remove the rotor (be careful not to damage the wiring harness), and finally remove the connecting parts and upper guide bearing seat. Unit assembly: before assembly, the rust and dirt of each component should be cleaned, and the sealant should be coated on each mating surface and fastener, and then assembled in the opposite order of disassembly (the movement of the motor shaft after assembly is about one millimeter), after the assembly is completed, the coupling should be flexibly rotated, and then the filter element should be placed for testing. Each time the underwater electric pump has been used for one year, or less than one year but has been immersed for two years, it must be disassembled and inspected in accordance with Article 5 and replace the worn parts.

 1, izpustite vodo iz votline motorja (zlasti pozimi, da preprečite zmrzovanje motorja) in dobro zavežite kabel.

 2, hranite v zaprtem prostoru brez jedkih snovi in ​​plinov, pri temperaturi pod 40 °C.

 3, dolgotrajna uporaba mora biti pozorna na preprečevanje rje potopnih črpalk.

01 Zajem vode iz globokega vodnjaka

02 Visoka oskrba z vodo

03 gorski vodovod 

04 stolpna voda

05 Namakanje v kmetijstvu

06 namakanje vrta

07 zajetje rečne vode

08 gospodinjska voda