300QJR Bamka Hoosta Hoose

This hot water pump adopts the motor made of 50W400 grade high quality cold rolled silicon steel, which is stamped by high speed punch press. It has the advantages of low stator iron loss and low self-heating. The motor winding is designed for hot water pump, high temperature resistance and anti-aging. The winding has water resistance, and adopts 3CR13 stainless steel blade shaft, high temperature resistant bushing and other high quality accessories to enable it to operate for a long time at high temperature, and can be used with frequency converter, so as to automatically adjust according to the amount of water used. This hot water pump is the ideal choice for your hot water equipment, which can operate stably and efficiently, providing you with a lasting hot water supply.

The product is a three-phase AC 380V (tolerance + / - 5%), 50HZ (tolerance + / - 1%) power supply submersible pump. With water quality requirements: water temperature is not higher than 20 °C; solid impurities content (mass ratio) is not more than 0.01%; PH value (pH) is 6.5-8.5; hydrogen sulfide content is not more than 1.5mg/L; chloride ion content is not more than 400mg/L. The electric pump adopts closed or water sealed wet structure, before use must be submersible motor inner cavity filled with clean water to prevent empty, and then tighten the water and air bolts, otherwise not to use. Its work should be completely immersed in water, immersion depth is not more than 70 meters, the distance between the bottom of the pump and the bottom of the well is not less than 3 meters. Well water inflow quantity should be able to meet the electric pump water output and continuous operation, the output water quantity should be controlled at 0.7-1.2 times of the rated flow. The well should be vertical, the electric pump can not be used horizontally or inclined, only vertically placed. The electric pump must be equipped with cables and external overload protection device as required. It is strictly prohibited to conduct no-load test under no water condition.

1, well submersible pump for clean water pump, prohibit the new well, pumping sediment and muddy water,

2, well water pump voltage grade of 380/50HZ, the use of other voltage grades of submersible motors need to be customized. The underground cable must use waterproof cable, must be equipped with starting equipment, such as distribution box, start not ready should have commonly used motor comprehensive protection function, such as short circuit overload protection, phase protection, undervoltage protection, grounding protection, idling protection, in case of abnormal conditions, the protection device should be timely action trip.

3, the installation and use of the pump must be reliably grounded, prohibit the push and pull switch when the hands and feet are wet, the installation and maintenance of the pump must be cut off the power supply, the use of the pump place to set up "to prevent electric shock" obvious signs:

4, down the well or before installation, the motor cavity must be filled with distilled water or non-corrosive clean cold boiling water, tighten the / water bolt, the pump on the ground test run, must be to the pump chamber water lubrication rubber bearings, instant start not more than a second, see whether the steering is the same as the steering instructions. When the pump is upright, pay attention to safety, prevent overturning injury.

5, si adag sida ku xusan qodobbada wiishka bamka, kala duwanaanshaha socodka isticmaalka, si looga hortago socodka hooseeya ama xoogga sare ee wiishka, xajinta iyo qaybaha kale ee xirashada, culeyska matoorka ayaa gubtay

6, ka dib markii bamka hoos ceelka, cabbiraadda motor in ay iska caabin dahaarka dhulka waa in aanay noqon wax ka yar 100M, ka dib markii bilowga si ay u dhawraan danab iyo hadda, hubi dahaarka dabaylaha motor, haddii si waafaqsan shuruudaha; heerkulka meesha lagu kaydiyo bamka haddii uu ka yar yahay barta qaboojinta, waa in lagu qallajiyaa biyaha godka matoorka, ka ilaali godka matoorka biyaha barafka ee uu keeno heerkulka hooseeya.

The pump part is mainly composed of pump shaft, impeller, shunt shell, rubber bearing, check valve body (optional) and other components. The motor part is mainly composed of base, pressure regulating diaphragm, thrust bearing, thrust plate, lower guide bearing seat, stator, rotor, upper guide bearing seat, sand discharging ring, water inlet section, lead cable and other components. The main characteristic of this product is that the motor is a water-cooled submersible three-phase asynchronous motor, and the motor cavity is filled with water to cool the motor and lubricate the bearing. The pressure regulating diaphragm at the bottom is used to adjust the expansion-contraction pressure difference in the body caused by the change of the temperature rise of the motor. In order to prevent the sand particles in the well water from entering the motor, two oil seals are installed at the upper end of the motor shaft extension, and a sand discharging ring is installed to form a sand discharging structure. In order to prevent the pump shaft from jumping when starting, the pump shaft and the motor shaft are connected together through a coupling, and a thrust bearing is installed at the bottom of the motor. The lubrication of the motor and the pump bearing is realized through water lubrication. The stator winding of the motor is made of high-quality well motor winding wire, with high insulation performance. The pump is designed by computer CAD, with simple structure and good technical performance.

(1) Diyaarinta ka hor inta aan la rakibin:
1. Hubi in bamka hoos mara uu buuxiyo shuruudaha isticmaalka iyo baaxadda lagu sheegay buug-gacmeedka.
2. Adigoo isticmaalaya dhexroor culus oo leh dhexroor la mid ah dhexroorka dibadda ee ugu sarreeya ee bamka hoos mara, cabbir haddii dhexroorka ceelka ceelka uu ku habboon yahay bamka hoos mara, cabbirna haddii qoto-dheeraanta ceelku buuxinayo shuruudaha rakibidda.
3. Hubi in ceelka ceelku uu nadiif yahay iyo in biyuhu ceelku yihiin kuwo gurracan. Weligaa ha isticmaalin bam koronto oo hoos iman kara si aad u dhaqdo bamka weriyaha dhoobada iyo biyaha ciidda si aad uga fogaato dhaawac degdeg ah oo soo gaadha bamka korontadu hoos u dhigto.
4. Hubi in booska xajinaha welhead ku habboon yahay iyo haddii ay u adkeysan karto tayada unugga oo dhan
5. Hubi in qaybaha matoorka hoos u dhigi karaan ay dhammaystiran yihiin oo si sax ah loo rakibay si waafaqsan jaantuska kulanka ee buug-gacmeedka, ka saar shaashadda oo beddel isku-xidhka si aad u aragto inay si dabacsan u wareegayso.
6. Ka fur furka biyaha oo ka buuxi godka matoorka biyo nadiif ah oo aan daxalaysan (xusuusnow in aad buuxiso), ka bacdina adkee xadhigga biyaha. Ka dib 12 saacadood oo duritaanka biyaha ah, caabbinta dahaarka ee matoorku waa in aanu ka yarayn 150M Q marka lagu cabbiro miis gariir 500V ah.
7. Isku-xidhka fiilada, ka jar caag 120mm ah oo ka mid ah daraf ka mid ah fiilada baxaysa iyo fiilada ku habboon ee leh mindi koronto-yaqaanka ka dibna ku rogrogmadaa dhererka saddexda fiilooyinka xudunta ah ee qaab go'an, ka saar xudunta 20mm naxaas ah, xoqin oksaydhka lakabka dibadda ee fiilada naxaasta leh mindi ama maro ciid, oo geli labada silig ee isku xidhan ee ku dhammaanaya palirs. Ka dib markaad lakabka si adag ugu xidho silig naxaas ah, si fiican oo adag u iibi, iyo ciid kasta. oogada dushiisa. Dabadeed, saddexda qaybood ee kala-goysyada, isticmaal cajaladda daboolka polyvester-ka si aad ugu duubto qaab nus ah oo isku xiran oo ah saddex berkedood. Ku duub labada daraf ee lakabka wax lagu duubo si adag adigoo isticmaalaya dunta nyion, ka dibna isticmaal qaab nus ah oo la tumay si aad ugu duubto cajaladda saddex lakab. Ku duub daboolka dibadda cajaladda daboolka cadaadiska sare ee saddex lakab. Ugu dambeyntii, isku laab saddexda xargo oo si isdaba joog ah ugu duub shan lakab oo leh cajalad cadaadis sare leh. Lakab kasta waa in si adag loo xidhaa, kala-goysyada is-dhexyaaca waa inay ahaadaan kuwo adag oo fim ah si ay uga hortagaan in biyuhu soo galaan oo waxyeello u geystaan ​​dahaarka. , kaas oo aan ka yarayn 100M Ω

Jaantuska habka fiilooyinka fiilooyinka ee ku lifaaqan waa sida soo socota:

8. Isticmaal multimeter-ka si aad u hubiso in xadhkaha saddexda weji ay isku xidhan yihiin iyo in iska caabbinta DC-ku ay qiyaas ahaan dheelli tiran yihiin.
9. Hubi in awoodda wareegga iyo beddelka ay si xad dhaaf ah u raran yihiin, ka dibna ku xidh furaha ilaalinta culayska ama qalabka bilowga. Ka eeg Shaxda 2 noocyo gaar ah, ka dibna ku shub baaldi biyo ah bamka biyaha ee ka soo baxa bamka biyaha si aad u saliidayn xadhkaha caagga ah ee bamka, ka dibna bamka korontadu hoos u dhigto dhig mid toosan oo joogto ah. Bilow (wax aan ka badnayn hal ilbiriqsi) oo hubi in jihada isteerinka ay waafaqsan tahay calaamadda isteerinka. Haddaysan ahayn, ku beddel laba xidhiidhiye oo ka mid ah fiilada saddexda weji leh. Kaddib rakib shaandhada una diyaari inaad ceelka dhaadhacdo. Haddii loo isticmaalo waqtiyo gaar ah (sida godadka, godadka, webiyada, balliyada, balliyada, iwm.), bamka korontadu waa in si la isku halleyn karo loo dejiyo.

(2) Qalabka iyo qalabka lagu rakibo:
1. Hal ka mid ah silsiladaha wax-qaadista ee ka badan laba tan.
2. Sadex geesood ah oo leh joog toosan oo aan ka yarayn afar mitir.
3. Laba xadhig oo ka laadlaad ah oo qaadi kara miisaan ka badan hal tan (waxay qaadi karaan culayska bambooyin biyo ah oo dhammaystiran).
4. Ku rakib laba-labo oo xajin ah (kabyo).
5. Biraha, dubbaha, kaashawiito, qalabka korontada iyo qalabka, iwm.

(3) Ku rakibida bamka korontada
1. Jaantuska rakibaadda ee bamka korontada hoostiisa ayaa lagu muujiyay Jaantuska 2. Cabbirrada rakibidda gaarka ah ayaa lagu muujiyay shaxda 3 "Liiska Cabbirrada Rakibaadda ee Bamka Korontada ee Submersible".

2. Bambooyin koronto oo hoos yimaada oo madax ka yar 30 mitir ayaa si toos ah loogu shubi karaa ceelka iyadoo la isticmaalayo tubooyinka iyo xargaha ama xargaha kale ee hemp kuwaas oo qaadi kara miisaanka buuxa ee dhammaan mishiinka, tuubooyinka biyaha, iyo biyaha tuubooyinka.

3. Bambooyin leh madax ka badan 30 mitir ayaa isticmaala tubooyinka birta, nidaamka rakibiddana waa sida soo socota.
①Isticmaal xajin si aad ugu xidho cidhifka sare ee qaybta matoorka biyaha (matoorka iyo bamka biyaha ayaa ku xidhan wakhtigan), ku qaad silsilad ka laadlaadsan, oo si tartiib ah ugu xidh ceelka ilaa aad xajinayso madaxa ceelka oo ka saar silsilad laadlaadsan.
② Isticmaal labo xajin oo kale si aad tuubada ugu xajiso, ku qaad silsilad laadlaad ah oo 15 cm ka fog garabka, oo si tartiib ah hoos ugu dhig. Inta u dhaxaysa flange tuubada iyo bamka bamka, dhig suufka caagga ah meesha oo adkee tuubada oo si siman ugu bamgareyso boolal, lawska iyo weelasha guga.
③ Xoogaa kor u qaad bamka hoos mara, ka saar xajinta cidhifka sare ee bamka biyaha, si adag ugu xidh fiilada tuubada biyaha cajalad balaastik ah, oo si tartiib ah hoos ugu xidh ilaa xajinta la dhigo madaxa ceelka.
④ Isticmaal isku qaab si aad ugu xidhid dhammaan tuubooyinka biyaha ceelka.
⑤Kadib markii fiilada macdanta "lead-out" lagu xiro furaha kantaroolka, waxay ku xiran tahay sahayda korontada ee saddexda weji.

(4) Waxyaabaha la xuso marka la rakibayo:
1. Haddi dhacdo isku buuqid ah la helo inta lagu jiro habka bamgareynta, leexi ama jiid tuubada biyaha si aad uga gudubto meesha saxmada leh. Haddii tillaabooyin kala duwani aanay weli shaqayn, fadlan ha ku qasbin bamka si aad uga fogaato burbur ku yimaadda bamka korontada ee hoos u dhigi kara iyo ceelka.
2. Inta lagu jiro rakibidda, suufka caagga ah waa in lagu dhejiyaa gees ka gees kasta oo tuubo ah oo la adkeeyo si siman.
3. Marka bamka biyaha lagu shubo ceelka waa in la dhex dhigaa dhuunta ceelka badhtankeeda si aanay bamku ugu socon darbiga ceelka muddo dheer, taasina ay keento in bamku gariiro oo matoorku xaaqo oo gubato. .
4. Go'aami qoto dheeraanta bamka biyaha ilaa gunta ceelka iyadoo loo eegayo ciidda qulqulaya iyo xaaladaha ciidda ee ceelka. Ha ku aasin bamka dhoobada. Masaafada u jirta bamka biyaha ilaa gunta ceelka guud ahaan waa mid aan ka yarayn 3 mitir (eeg sawirka 2).
5. Moolka gelitaanka biyaha ee bamka biyuhu waa in aanu ka yarayn 1-1.5 mitir heerka biyaha firfircoon ilaa marinka biyaha gelitaanka (eeg sawirka 2). Haddii kale, xadhkaha matoorka biyaha ayaa si fudud u dhaawacmi kara.
6. Wiishka bamka biyuhu ma noqon karo mid aad u hooseeya. Haddii kale, waxaa loo baahan yahay in lagu rakibo tuubada biyaha ee albaabka ceelka si loo xakameeyo socodka bamka ee barta socodka lagu qiimeeyay si looga hortago in matoorku uu si xad dhaaf ah u raro oo uu u gubto heerka socodka badan ee socodka awgeed.
7. Marka bamka biyuhu socdo, wax-soo-saarka biyuhu waa inuu ahaado mid joogto ah oo xitaa, hadda waa inuu ahaado mid deggan (marka la qiimeeyo xaaladaha shaqada, guud ahaan wax aan ka badnayn 10% ee hadda la qiimeeyay), waana inaysan jirin gariir ama buuq. Haddii ay jiraan wax aan caadi ahayn, mashiinka waa in la joojiyaa si loo ogaado sababta oo loo tirtiro.
8. Markaad rakibayso, fiiro gaar ah u yeelo goobta siliga goynta matoorka (eeg sawirka 2). Marka dhuumaha biyuhu ay yihiin tuubo bir ah, ka soo hoggaami xajinta madaxa ceelka; marka tuubada biyuhu ay tahay tuubo caag ah, ka soo jiid calaamadda dhulka ee bamka korontada.

 After installation of the underwater pump, it is necessary to recheck the insulation resistance and three-phase continuity of the switch, and check whether the connection between the instrument and the starting equipment is wrong. If there is no problem, you can start the test machine. After starting, observe whether the indication reading of each instrument is correct. If the rated voltage and current specified on the nameplate are exceeded, observe whether the pump has any noise or vibration. If everything is normal, it can be put into operation. Four hours after the first operation of the pump, it should be turned off and the thermal insulation resistance of the motor should be quickly tested, and its value should not be less than 0.5 megaohm. After stopping the pump, it should be restarted after an interval of five minutes to prevent the water column in the pipeline from completely reversing, resulting in the motor burning due to excessive current. After the pump is put into normal operation, in order to prolong its service life, it is necessary to check regularly whether the supply voltage, working current and insulation resistance are normal. If the following conditions are found, the machine should be stopped immediately to eliminate the fault:

1 the current exceeds 20% under the rated working condition.

2 the dynamic water level drops to the inlet section, resulting in intermittent drainage.

3 the underwater pump vibrates violently or emits huge noise.

4 the supply voltage is lower than 340 volts.

5 a fuse is burned.

6 the water pipe is damaged.

7 the thermal insulation resistance of the motor to the ground is less than 0.5 megaohm.

When disassembling the device, it is necessary to untie the cable bundle and remove the pipeline part and the line protection plate. Remove the drain bolt and exclude all water in the motor chamber. Remove the filter element and loosen the screw on the coupling fixed to the motor shaft. Unscrew the bolt connecting the water inlet section and the motor, and separate the pump and the motor (pay attention to placing the device horizontally when separating to prevent the bending of the pump shaft). The sequence of disassembling the pump is as follows: (see Figure 1) water inlet section, impeller, water inlet shell, impeller. Check the valve body, and use a special tool to loosen the cone sleeve fixed to the impeller when removing the impeller. In the process of disassembly, avoid bending the pump shaft and damaging various components. The disassembly process of the motor is as follows: (see Figure 1) put the motor on the platform, and remove the nuts on the screw (pull rod bolt), base, shaft head lock nut, thrust plate, key and lower guide rail - bearing seat, bolt, and then remove the rotor (be careful not to damage the wiring harness), and finally remove the connecting parts and upper guide bearing seat. Unit assembly: before assembly, the rust and dirt of each component should be cleaned, and the sealant should be coated on each mating surface and fastener, and then assembled in the opposite order of disassembly (the movement of the motor shaft after assembly is about one millimeter), after the assembly is completed, the coupling should be flexibly rotated, and then the filter element should be placed for testing. Each time the underwater electric pump has been used for one year, or less than one year but has been immersed for two years, it must be disassembled and inspected in accordance with Article 5 and replace the worn parts.

 1, dami biyaha godka matoorka (gaar ahaan xilliga jiilaalka si aad uga hortagto matoorku baraf), oo si fiican u xidh fiilada.

 2, ku kaydi qol gudaha ah oo aan lahayn walxo daxalaystay iyo gaas, kulaylkiisuna ka hooseeyo 40 °C.

 3, isticmaalka muddada dheer waa in fiiro gaar ah u leh ka hortagga miridhku ee matoorada submersible.

01 Qaadashada biyaha ceelka qoto dheer

02 Biyo-helid-sare

03 biyaha buuraha 

04 munaaradaha biyaha

05 waraabka beeraha

06 waraabka beerta

07 qaadashada biyaha webiga

08 biyaha guriga