125QJB Deep Well Submersible Pump

Frequency conversion winding design, ensure the motor in 1HZ-50HZ long-term stable conversion operation. Energy saving, longer service life.

1, napajanje: trofazni AC 380V (tolerancija +/- 5%), 50HZ (tolerancija +/- 1%).

2, kvaliteta vode:

(1) water temperature is not higher than 20 °C;

(2) sadržaj krutih nečistoća (maseni omjer) nije veći od 0,01%;

(3) PH vrijednost (pH) 6,5-8,5;

(4) sadržaj sumporovodika nije veći od 1,5 mg/L;

(5) sadržaj kloridnih iona nije veći od 400 mg/L.

3, motor je zatvoren ili napunjen vodom mokra struktura, prije upotrebe šupljina potopnog motora mora biti puna čiste vode, kako bi se spriječilo lažno puno, a zatim zategnite ubrizgavanje vode, vijke za oslobađanje zraka, inače nije dopušteno koristiti

4, potopna pumpa mora biti potpuno uronjena u vodu, dubina ronjenja nije veća od 70 m, dno potopne pumpe od dna bunara nije manje od 3 m.

5, protok vode iz bunara trebao bi biti u stanju zadovoljiti izlaz vode potopne pumpe i kontinuirani rad, izlaz vode potopne pumpe treba kontrolirati na 0,7 - 1,2 puta od nazivnog protoka.

6, bunar bi trebao biti ravan, potopna pumpa se ne može koristiti ili baciti, samo okomita uporaba.

7, potopna pumpa mora biti usklađena s kabelom prema zahtjevima i vanjskim uređajem za zaštitu od preopterećenja. 8, pumpa je strogo zabranjena bez vode bez stroja za testiranje

 The well submersible pump is a pump suitable for clear water. It is strictly prohibited to dig new wells and pump out mud and sand. The voltage grade of the well pump is 380V/50HZ, and other voltage grades of the submersible motor need to be customized. Underground cables must be waterproof cables and must be equipped with starting equipment, such as distribution box, etc. The starting equipment should have common motor comprehensive protection functions, such as short circuit overload protection, phase loss protection, undervoltage protection, grounding protection and idling protection, etc. In abnormal cases, the protective device should be tripped in time. When installing and using the pump, it must be firmly grounded. It is prohibited to push and pull the switch when the hands and feet are wet. The power supply must be cut off before installing and maintaining the pump. An obvious "anti-electric shock" sign must be set up where the pump is used. Before going down the well or installing the motor, the inner cavity must be filled with distilled water or non-corrosive clean cold water, and the water injection/drainage bolts must be tightened. Fill the pump with water for ground test to lubricate the rubber bearings. The instant start time shall not exceed one second to check whether the direction is correct and consistent with the direction indication. Be sure to pay attention to safety when placing the pump upright to prevent overturning and causing injury. Strictly in accordance with the provisions of the pump lift and flow range of use, to prevent the pump flow at low lift or excessive pull at high lift, resulting in extreme wear of thrust bearings and other components, resulting in motor overload burn. After the pump into the well, the insulation resistance between the motor and the ground shall be measured, which shall not be less than 100MΩ. After the start, observe the voltage and current regularly, and check the motor winding insulation, to see if it meets the requirements; if the pump storage temperature is below the freezing point, the water in the motor cavity should be discharged, so as to avoid the water in the motor cavity freezing and damaging the motor due to low temperature.

The pump part is mainly composed of pump shaft,impeller,diversion shell,rubber bearing,check valve body(optional)and other components.The motor part is mainly composed of base,pressure regulating diaphragm,thrust bearing,thrust plate,lower guide bearing seat,stator,rotor,upper guide bearing seat,sand ring,water inlet section,lead cable and other components.

Glavne značajke proizvoda uključuju:

1.The motor is a water-loaded wet submersible three-phase asynchronous motor,and the motor cavity is filled with clean water for cooling the motor and lubricating the bearing.The regulating diaphragm at the bottom of the motor is used to adjust the expansion and contraction pressure difference inside and outside the body caused by the temperature rise of the motor.
2.In order to prevent the sand particles in the well water from entering the motor,two oil seals are installed at the extension end of the motor shaft,and the sand ring is installed to form a sand prevention structure.
3.In order to prevent the pump shaft from jumping when starting,the pump shaft is connected with the motor shaft through a coupling,and the thrust bearing is installed at the bottom of the motor.
4.The lubrication of the motor and the pump bearing is water lubrication.
5.The stator winding of the motor adopts high-quality submersible motor winding wire,with excellent insulation performance.
6.The pump is designed by computer CAD,with simple structure and excellent technical performance.

(1)Priprema prije instalacije:
1. Provjerite zadovoljava li potopna pumpa uvjete uporabe i opseg navedene u priručniku.
2. Pomoću teškog predmeta promjera jednakog najvećem vanjskom promjeru potopne pumpe, izmjerite može li unutarnji promjer bušotine odgovarati potopnoj pumpi i izmjerite zadovoljava li dubina bunara zahtjeve za ugradnju.

3. Provjerite da li je bušotina čista i da li je bunarska voda mutna. Nikada nemojte koristiti potopnu električnu pumpu za ispiranje blata i pijeska vode pumpe kako biste izbjegli prerano oštećenje potopne električne pumpe.

4. Provjerite je li položaj stezaljke za ugradnju glave bunara prikladan i može li izdržati kvalitetu cijele jedinice

5. Provjerite jesu li komponente potopne crpke dovršene i pravilno postavljene prema dijagramu sastavljanja u priručniku. Uklonite mrežicu filtra i zakrenite spojnicu da vidite okreće li se fleksibilno

6. Odvijte vijak za vodu i ispunite šupljinu motora čistom, ne korozivnom vodom (napomena. obavezno je napunite), zatim zategnite vijak za vodu. Nakon 12 sati ubrizgavanja vode, izolacijski otpor motora ne bi trebao biti manji od 150M Q kada se mjeri s 500V tresećom tablicom.
7. Cable joint, cut off a 120mm rubber sleeve from one end of the outgoing cable and the matching cable with an electrician's knifethen stagger the length of the three core wires in a stepped shape, peel off a 20mm copper core, scrape of the oxide layer on theoutside of the copper wire with a knife or sand cloth, and insert the two connected wire ends in palirs.

After tying the layer tightly with fine copper wire, solder it thoroughly and firmly, and sand of any. burrs on the surface. Then, forthe three joints, use polyvester insulation tape to wrap them in a semi stacked manner for three lavers. Wrap the two ends of thewrapping layer tightywith nyion thread,and then use a semi stacked method to wrap the tape for three layers. Wrap the outellayer with high-pressure insulation tape for three layers. Finally, fold the threestrands together and repeatedly wrap them for fivelayers with high-pressure tape. Each layer must be tightly tied, and the interlayer joints must be tight and fimm to prevent water frompenetrating and damaging the insulation, After wrapping, soak in water at room temperature of 20 ’c for 12 hours, and measurethe insulation resistance with a shaking table, which should not be less than 100M Ω

Priloženi dijagram procesa ožičenja kabela je sljedeći:

8. Multimetrom provjerite jesu li trofazne žice spojene i je li otpor istosmjerne struje približno uravnotežen.
9. Check whether the circuit and transformer capacity are overloaded, and then connect the overload protection switch or starting equipment. See Table 2 for specific models, and then
Pour a bucket of water into the water pump from the water pump outlet to lubricate the rubber bearings in the pump, and then place the submersible electric pump upright and steady.
Start (no more than one second) and check whether the steering direction is consistent with the steering sign. If not, swap any two connectors of the three-phase cable.
Then install the filter and prepare to go down the well. If used in special occasions (such as ditches, ditches, rivers, ponds, ponds, etc.), the electric pump must be reliably grounded.

(2) Oprema i alati za ugradnju:
1. Jedan par lanaca za podizanje više od dvije tone.
2. Stativ s okomitom visinom ne manjom od četiri metra.
3. Dva viseća užeta (žičana užad) koja mogu podnijeti težinu veću od jedne tone (mogu podnijeti težinu kompletnog seta pumpi za vodu).
4. Ugradite dva para stezaljki (udlaga).
5. Ključevi, čekići, odvijači, električni alati i instrumenti itd.

(3) Instalacija električne pumpe:
1. Dijagram ugradnje potopne električne crpke prikazan je na slici 2. Specifične ugradbene dimenzije prikazane su u tablici 3 "Popis ugradbenih dimenzija potopne električne pumpe".

2. Potopne električne pumpe s visinom manjom od 30 metara mogu se podići izravno u bunar pomoću crijeva i žičane užadi ili druge užadi od konoplje koja može podnijeti punu težinu cijelog stroja, cijevi za vodu i vode u cijevima.

3. Crpke s visinom većom od 30 metara koriste čelične cijevi, a redoslijed ugradnje je sljedeći:
①Use a clamp to clamp the upper end of the water pump part (the motor and water pump have been connected at this time), lift it with a hanging chain, and slowly tie it into the well until
Put the clamp on the wellhead and remove the hanging chain.
② Use another pair of clamps to clamp a pipe, lift it with a hanging chain 15 cm away from the flange, and lower it slowly. Between pipe flange and pump flange
Put the rubber pad in place and tighten the pipe and pump evenly with bolts, nuts and spring washers.
③ Lagano podignite potopnu pumpu, uklonite stezaljku na gornjem kraju pumpe za vodu, čvrsto zavežite kabel za cijev za vodu plastičnom trakom i polako je pričvrstite dok se stezaljka ne postavi na ušće bunara.
④Upotrijebite istu metodu za vezivanje svih cijevi za vodu u bunar.
⑤ Nakon što je izlazni kabel spojen na upravljačku sklopku, spaja se na trofazno napajanje.

(4) Stvari koje treba imati na umu tijekom instalacije:
1. If a jamming phenomenon is found during the pumping process, turn or pull the water pipe to overcome the jamming point. If various measures still do not work, please
Do not force the pump down to avoid damage to the submersible electric pump and the well.
2. Tijekom instalacije, gumeni jastučić treba postaviti na prirubnicu svake cijevi i ravnomjerno ga zategnuti.
3. Kada se pumpa za vodu spusti u bunar, treba je postaviti na sredinu cijevi bunara kako bi se spriječilo da pumpa dugo radi uz zid bunara, uzrokujući vibriranje pumpe, a motor brisanje i paljenje .
4. Odredite dubinu pumpe za vodu do dna bušotine prema uvjetima protoka pijeska i mulja u bušotini. Ne zakopavajte pumpu u blato. Udaljenost od pumpe za vodu do dna bunara općenito nije manja od 3 metra (vidi sliku 2).
5. Dubina ulaza vode u pumpu za vodu ne smije biti manja od 1-1,5 metara od dinamičke razine vode do čvora za dovod vode (vidi sliku 2). Inače se ležajevi vodene pumpe mogu lako oštetiti.
6. Podizanje vodene pumpe ne smije biti prenisko. U suprotnom, na cjevovod za vodu na ušću bušotine potrebno je instalirati zasunski ventil za kontrolu protoka crpke na nazivnoj točki protoka kako bi se spriječilo preopterećenje motora i njegovo sagorijevanje zbog velikih protoka.
7. Kada pumpa za vodu radi, izlaz vode treba biti kontinuiran i ravnomjeran, struja bi trebala biti stabilna (pod nazivnim radnim uvjetima, općenito ne više od 10% nazivne struje), i ne bi trebalo biti vibracija ili buke. Ako postoji bilo kakva nepravilnost, stroj treba zaustaviti kako bi se otkrio uzrok i otklonio ga.
8. Prilikom postavljanja obratite pozornost na postavku žice za uzemljenje motora (vidi sliku 2). Kada je cijev za vodu čelična cijev, vodite je od stezaljke na ušću bušotine; kada je cijev za vodu plastična, vodite je od oznake za uzemljenje električne pumpe.

• 1. Nakon što je potopljena crpka instalirana, ponovno provjerite izolacijski otpor i trofazni vod od prekidača, provjerite jesu li instrument i priključak opreme za pokretanje pogrešni, ako nema problema, probni stroj se može pokrenuti, i promatrajte da li očitanja indikatora instrumenta premašuju nazivni napon i struju navedene na natpisnoj pločici nakon pokretanja, i promatrajte ima li pumpa buku i vibracije i pustite je u rad ako je sve normalno.
• 2. Nakon prvog rada crpke tijekom četiri sata, motor treba isključiti kako bi se brzo ispitao otpor toplinske izolacije, a njegova vrijednost ne smije biti manja od 0,5 megaohma.
• 3. Nakon što se pumpa isključi, treba je pokrenuti nakon pet minuta kako bi se spriječilo da se vodeni stupac u cijevi potpuno pretače i izazove pretjeranu struju motora i pregorevanje.
• 4. Nakon što je crpka puštena u normalan rad, kako bi se produžio njezin radni vijek, potrebno je redovito provjeravati jesu li napon napajanja, radna struja i otpor izolacije normalni. Ako se pronađu sljedeća stanja, crpku treba odmah isključiti radi otklanjanja problema.
•  
• 1 In the rated condition, the current exceeds 20%.
• 2 Dinamička razina vode pada do dijela za dovod vode, uzrokujući povremenu vodu.
• 3 Potopna pumpa ima jake vibracije ili buku.
• 4 Napon napajanja je manji od 340 volti.
• 5 Osigurač je pregorio.
• 6 Cijev za dovod vode je oštećena.
• 7 The motor's thermal insulation resistance is lower than 0.5 megaohm.
•  
• Unit disassembly:
• 1.Untie the cable tie, remove the pipeline part, and remove the wire plate.
• 2.screw down the water bolt, put the water in the motor chamber.
• 3.remove the filter, loose the fixed screw on the coupling to fix the motor shaft.
• 4.screw down the bolt connecting the water inlet section with the motor, and separate the pump from the motor (pay attention to the unit cushion when separating, to prevent the bending of the pump shaft)
• 5.the disassembly sequence of the pump is: (see figure 1) water inlet section, impeller, diversion shell, impeller...... check valve body, when removing the impeller, use special tools to loosen the conical sleeve of the fixed impeller first, and avoid bending and bruising the pump shaft in the process of disassembly.
• 6.the disassembly process of the motor is: (see figure 1) place the motor on the platform, and remove the nuts, base, shaft head locking nut, thrust plate, key, lower guide bearing seat and double head bolt from the bottom of the motor in turn, and then take out the rotor (pay attention not to damage the wire package) and finally remove the connecting section and upper guide bearing seat.
• 7.unit assembly: before assembly, the rust and dirt of the parts should be cleaned, and the mating surface and fasteners coated with sealant, and then assembled in the opposite order of disassembly (the motor shaft moves up and down after assembly for about one millimeter), after assembly, the coupling should be flexible, and then the filter screen test machine. Submersible pumps shall be taken out of the well for dismantling and maintenance according to Article 5 after a year of operation, or less than a year of operation but two years of diving time, and the worn parts shall be replaced.

This product is an efficient and durable submersible electric pump, suitable for a variety of environments and applications.In order to ensure the long-term use and stable performance of the product, we suggest that users pay special attention to drying the water in the motor cavity in winter to avoid freezing; in addition, the cable is coiled and tied, and properly stored in an environment without corrosive substances and gases, with a temperature below 40 °C. If the product is not used for a long time, attention should be paid to rust prevention treatment to ensure the life cycle and performance of the product.Whether for industrial use or for home use, this submersible electric pump can provide you with reliable pump service.

1. • impeler
   • Čahura osovine
   • Gumeni rukavac osovine

   •  Brtveni prsten

01 Zahvat dubokih bunara

02 Visokoprizemni vodovod

03 planinski vodovod 

04 toranj voda

05 Poljoprivredno navodnjavanje

06 navodnjavanje vrta

07 riječni vodozahvat

08 domaća voda